Chapter 6 Controlling the Multi-Projectors Chapter 7 Use of Serial Port Chapter 9 Appendix This PJ-Net Organizer is an optional network product for the projector. Mount this product to the projector and connect a network cable. It enables a projector to display the image data stored in the file server and the screen image of the computer via the network.
Model Numbers : POA-PN02 Trade Name : Sanyo Responsible party : SANYO FISHER COMPANY Address : 21605 Plummer Street, Chatsworth, California 91300 Telephone No. : (818)998-7322 - When you receive an alert e-mail from the projector, you must check the projector immediately.
Contents Chapter 1 Preparation ....... . .5 Features ..........6 Operating Environment .
Contents Load an image mode ........46 Screen .
Chapter 1 Preparation Network Unit OWNER’S MANUAL...
Chapter 1 Preparation Features Network Capture function It enables a projector to project the screen image of the computer on the screen via the network by using an exclusive utility software . Network Viewer function The projector receives the image data stored in the file severs in the network and dis- plays images automatically.
Web Management function With this function, you can monitor projector functions such as power status, lamp status, input mode, signal condition, lamp-use time, etc. through the network by using the web browser installed on your computer. Turn on PJ2. E-Mail Alert function The projector (Network Unit) sends messages to the registered e-mail addresses when a lamp abnormality or power failure occurs with the projector.
Chapter 1 Preparation Multi-control function A single computer can control and set up the multiple computers at the same time. Automatic On/Off using Clock function Automatically turn on or off the projectors at specified date/day and time by using the clock function.
128 MB of RAM or higher recommended (64 MB minimum supported) 100 MB of available hard-disk space VGA or higher-resolution video adapter and monitor CD-ROM drive 10Base-T or 100Base-TX network card Web browser application* Microsoft Internet Explorer version 5.0, 5.5 or 6.0. Netscape Navigator version 6.1, 6.2 or 7.0.
Chapter 1 Preparation The limitation of connection between this product and Hub or Computer Suitable LAN cables are limited by length and type as follows; Connection Network Unit - Hub Network Unit - Computer *1 There may be other limitations depending on your network environment or LAN specifica- tion.
Trademarks PJ-Net Organizer is a registered trademark of SANYO Electric Co., Ltd. Ethernet is a registered trademark of Xerox Corporation. Microsoft, Windows, Windows NT are registered trademarks of Microsoft Corporation. Internet Explorer is a registered trademark of Microsoft Corporation.
Chapter 1 Preparation Software License Agreement Before using Network Viewer & Capture Software CD-ROM, thoroughly read the following software license agreement to fully understand its contents. Use this CD-ROM only when you agree to the terms of this agreement. If you do not agree to the terms, do not use this CD-ROM. Software License Agreement This is a legal agreement between the customer (hereafter referred to as "user") and Sanyo Electric.
Chapter 2 Installation Network Unit OWNER’S MANUAL...
Chapter 2 Installation Flow of installation The following are instructions for attaching this product to the projector and connect- ing it to the network. Please review the entire procedure to become familiar with it. Function of the Network Unit Explains the name and functions of each part of the network unit. Installation and network configuration Mount this product onto the projector.
z Name and function of each part Power indicator This lights up red when the net- work function is set ON in the projector menu. Serial port This is used when controlling the external equipment via the network. ( p.85) LAN port Connecting the LAN cable.
Chapter 2 Installation x Installation and Network configuration Mounting Disconnect the AC plug from the projector. Remove the connector cover and screw covers from the pro- jector and insert plug on this product to the option connector. Tighten two screws by using a coin etc.
Connection of LAN cable To connect to the network, it is required to use the UTP (Unshielded Twisted Pair) strait cable with RJ-45 plug. There are two different types of cables depending on whether the network is constructed with 10Base-T or 100Base-TX. Prepare the Hub (10Base-T or 100Base-TX) to distribute the network cable if required.
Chapter 2 Installation Network configuration Confirmation of the network menu When installing this product to the projector, the network on-screen menu items for this product are activated automatically. If not activated, the product may not have been installed correctly. Please check item “Mounting” ( Configure the network When you connect the projector to the network, the network number of projector must be the same as the network you intend to connect.
Configuration for IP Address/ Sub net/ Gateway*/DNS* Press SELECT button again, the following network setting menu appears on the screen. Enter the specified network address. Restart the Network Unit Select Set with 7 8 keys and press SELECT button again. The network configu- ration display disappears and the network unit begins restarting.
Chapter 2 Installation Password setting A password can be set to restrict access to the setting pages of the projector using the web browser. The default password is set “0000” as no password. Use the projector’s menu and select the Network setting icon on the menu. Select the Network setting sub icon from the submenu, and then press SELECT button once.
How to enter the numbers with the screen 10-key pallet Select a column with a red frame by using the point buttons 7 8 . Press SELECT button. The screen 10-key pallet appears on the screen. By using the point buttons(d e 7 8), select numbers 0 to 9 and press SELECT button.
Chapter 2 Installation c Installing the software It is required to install the software into your computer to use the Network Capture function and Network Viewer function. Please install the following procedure. Note: To install the software into the computer with Windows 2000, Windows XP or Windows NT, you should login with administrator rights.
Installed software The following 3 software are installed on your computer. Network Capture: Capture the displayed image of the computer and serve it to the projector via the network. This software is registered into “startup folder” of the computer and the capture icon stays on the task bar after booting the com- puter.
Chapter 2 Installation File Converter 2 Installation Set the supplied Network Viewer & Capture CD-ROM into the CD-ROM drive your computer. SetupDrv.exe icon in the “Driver” folder in the CD-ROM. Select “English [United States]”from the pull-down menu on the language selec- tion window and then click Install button to start installing.
Chapter 3 Basic Setting and Operation Network Unit OWNER’S MANUAL...
Chapter 3 Basic Setting and Operation This chapter describes basic operations and settings for controlling the projector via a network using this product. It is required that computer and projector be connected to the network and the network address be properly configured. Login the setting page of the projector Enter the IP address Launch the web browser installed in...
Display of main setting page The following main setting page will be displayed according to your display mode selection. Perform the various kinds of setting through this page. Click on the menus to display the control and setting pages. Main setting page in the Graphic Mode display Main menu For selection of control and set- ting items of the projector.
Chapter 3 Basic Setting and Operation Main setting page in the Text Mode display Returns to the display mode selection page. The network viewer function in the text mode has following limitation; - Cannot select the program or folder for the display ( - Cannot perform the registration, check or change of the program ( Main menu For selection of control...
Initial Settings After installing this product to the projector, perform the following basic ini- tial setting. Click Initial Setting on the main menu to display the initial setting page. The Languages, Date/Time, Password and Temperature unit can be set in this page. The model name of the projector on which this product is mounted is displayed on the page.
Chapter 3 Basic Setting and Operation Password Setting This page is to set the password to restrict the access from an unauthorized per- son through the network. Enter the password onto the text box and click Set button. The Network Unit begins restarting and it takes about 40 seconds. Close (Quit) the web browser and access to the login page again in 40 seconds.
Date/Time Setting Click on the page number “2” to display the Time Setting page. Type present date onto the date text area (Year/Month/Date) format and type present time onto the time text area (Hour:Minute) format in 24 hours indication. Click Set but- ton and confirm that the data and time are set correctly.
Chapter 3 Basic Setting and Operation Network Configuration Click Network on the main menu. The following setting page is displayed. This page is to set the IP Address, Subnet Mask, Default Gateway, DNS (Domain Name Server) and projector name. Configure the network The IP address and Subnet Mask have been configured already in chapter “Installation”.
E-mail Setting This product has an E-mail function which can send an alert message to users or an administrator if it detects an abnormality on the projector or run out of the life span of the lamp. Click E-Mail Setting on the main menu and follow the below steps.
Chapter 3 Basic Setting and Operation Registering and deleting E-mail addresses Type the E-mail address onto the Mail Address text area and click Set button. To check the registered addresses, click on the Mail Address Check & Delete linked text. addresses are listed as the fig- ure on the right.
Condition selection for sending alert message Check the condition items under which alert messages will be sent and click Set button. A free message can be sent when the lamp use time reach- es the preselected lamp use time. Check this condition and enter a setting time.
Chapter 3 Basic Setting and Operation When the internal power circuit is failed: TITLE: Message from projector 01-03-2003 00:59 Projector Model Name: XP50/55 TCP/IP: 192.168.1.201 Projector Name: myProjector It sends you following message. *The Projector lamp was turned off, because projector power circuit failed. Unplug the projector from AC outlet and ask servicing to qualified service personnel.
Chapter 4 Controlling the Projector Network Unit OWNER’S MANUAL...
Chapter 4 Controlling the Projector This chapter describes controlling the projector via a network using this product. Display the main menu following to the login procedure described on page 26. Power on/off the projector Click Power & Status on the main menu. The control page will be displayed. By clicking On or Standby button on the page, the power of the projector can be controlled.
Check the status of projector In the “Power & Status” page, you can control the projector power, and also you can check the status of the projector as follows. To change the page, click on the page number linked text. Items Description Accumulated...
Chapter 4 Controlling the Projector Control the projector The sub control menu appears on the lower side of the page when clicking Control on the main menu. When you click each control icon, the control page is displayed according to the control menu you selected. The setting method differs depending on the contents of the page.
Input This function is to select the input mode and source mode of the projector. Select the input mode with the radio button, and input source mode with the pull-down menu button. Then set the selected input mode and source mode by clicking Set button.
Chapter 4 Controlling the Projector PC Adjustment This function is to adjust the signal from the computer connected to the projector to obtain the proper picture image on the screen. Click on the page number linked texts to change the setting pages. These parameters will appear only when the RGB(Analog) or Network input mode is selected.
Save a Set Decide your desired PC adjustment val- ues through the PC Adjustment pages “1”to “2”. Display the page “3” and select a mode number with the pull-down menu button of the Save to. Type a memo into the Memo text area for simply description of your selected number.
Chapter 4 Controlling the Projector System Adjustment This function is to select the color system of video signal or scanning sys- tem of component signal input to the projector. Select a system with the radio buttons to match the color system or scanning system of input source, and then click Set button.
Image Adjustment This function is to adjust the projected picture image and set the image mode. For selection of image mode, select a desired image mode with the Image pull-down menu button and then click Set button. The setting items are switched automatically according to selected input mode, computer or video input.
Chapter 4 Controlling the Projector Save an image adjustment value Decide your desired image adjustment value through the image adjustment pages “1” to “3”. Display the page “3” and select the desired image number with the pull- down menu of the Save Adjustment. Register by clicking Set button.
Screen This function is to adjust the screen mode of the projector. The setting items are switched automatically according to selected input mode, com- puter or video input. Sound This function is to adjust the sound of the projector. The values in the text box represent the current control value or status.
Chapter 4 Controlling the Projector Setting This function is to set up the projector. Click on the page number “1” to “6” linked texts to change the setting pages. * The displayed items may differ from the actual depending on the functions of the projector you use.
Chapter 4 Controlling the Projector How to set the Timer This function is used to turn the projector off or on at a programmed day/date and time. Follow the below steps for setting. Set a day or date To set the timer event at same time everyday, select “day”...
Set a time Type the time with (Hour:Minute) and 24 hours format. Ex.: Type [18:25] if you specify [PM 6 o’clock and 25 minutes]. Select an event “ON” or “OFF”. Select an event ON or OFF with the pull-down menu button to turn on or off the projector.
Chapter 4 Controlling the Projector Notes on timer setting Up to 10 timer events can be registered. Timer events always operate according to the next valid event depending on the projector's power status. In the example below, event 3 turns on the projector so next event 4 (also turning on projector) will not be effective because the projector is already turned on.
Control the projector Service This function sets the cooling fan speed of the projector. Set proper fan speed depending on the installation environment. Select “Normal” or “Maximum” with the pull-down menu button and click Set button. Network Unit OWNER’S MANUAL...
Chapter 4 Controlling the Projector Save Actual Adjustment This function is to save and load the control values of the projector. The storable control items are Input, PC, System, Image and Screen controls, and these control items differ from each selected input mode and functions of the projector you use.
Control the projector Check the Save items Browse pages by clicking on the page numbers and check each setting status. The pages for the saving items are constructed by 8 pages. The contents of the pages may differ from the actual depending on the selected input mode and the function of the projector.
Chapter 4 Controlling the Projector Load a control set Select your desired set number with the pull-down menu button of the Load Setting No. and then click Set button. The setting values of the selected set number are applied to the current settings. Example of setting...
Control the projector's menu Click Menu on the main menu. The following menu control page is dis- played. This page is to control the on-screen display menu of the projector. Item Description Display Menu ...To switch the on-screen display menu on or off by clicking ON or OFF button. The same operation with the MENU button on the projector and remote control handset.
Chapter 4 Controlling the Projector Make a memo Select the Memo setting page by clicking Memo on the main menu. The following setting page is displayed. It is convenient to use as a memo for the simple description where the projector is placed in. This note will be displayed on the login page.
Chapter 5 Network Viewer & Capture Network Unit OWNER’S MANUAL...
Chapter 5 Network Viewer & Capture Using the Network Capture function The Network Capture is a function to project the screen images of the computer by the projector via the network by using the Network Viewer software. Up to 10 com- puters can be registered and the capture images of the computer projected by the projector can be selected by the Network Capture software in the computer, web browser and projector.
Click Search button to list up the available IP address assign to the projector and select desired IP address you use, or you can enter the IP address manually if you know that IP address. Set the quality of the image. Quality: Selects from High, Mid, Low Image Magnification: If checked, the screen image size of the computer is automatically adjusted to the projector’s screen size.
Chapter 5 Network Viewer & Capture  Control by the web browser * PC privided with the Network Capture. Select input mode to the “Network” previously. Access to the control page on the projector by using the web browser. From the main menu, click Network Capture to display the setting page ( Select the computer number to connect from the pull-down menu button of “Connecting PC”...
Registering the computers Up to 10 computers can be registered. To register a computer, on the Network Capture setting page, click the page num- ber “2” or “3” linked text to change to “Connection Setting” page and enter the IP address of the computer to the PC number, and then click Set button.
Chapter 5 Network Viewer & Capture Advanced using example Displays the presentation data stored in the computer by using the wireless mouse function from the projector. Start capturing of the computer PC1 by using the projector. Select “Network Capture” icon from the menu and select “PC1” and then select “Connect” p.63).
Create the available data [File Converter] The image available with this projector is the JPEG format. There are several types of JPEG data. Before using the images with the Network Viewer function, it should be converted to the optimized JPEG data for this projector.  How to use the Network Viewer (File Converter 1) The File Converter 1 is a software to convert from the JPEG data or bitmap data to the optimized JPEG data for the projector.
Chapter 5 Network Viewer & Capture Converting procedure Select a folder in which the image files are stored by the explorer window. The preview images of the available image data (JPEG file, BMP file) in the select- ed folder are displayed on the preview window. * On the preview window, the preview displayed with the red frame represents a file not optimized JPEG file or BMP file for the projection.
Setting of conversion mode When clicking Change button on the confirmation window in the step 3 on the previ- ous page, following option setting window appears. Conversion type: Fit ...Converts as either width or height of the image sets to be the maximum screen width or height.
Chapter 5 Network Viewer & Capture  How to use the Network Viewer (File Converter 2) The File Converter 2 is a kind of the printer driver software to convert to the opti- mized JPEG data for the projection from the any documents created by the other software such as text editor, spreadsheet or presentation software.
Making a program file [Program Editor] Network Viewer (Program Editor) is a tool to make a program file specify the stored information of the JPEG images in the file server (ftp server) and the order of the dis- play images. Program Editor makes a folder “DispParam” at the login root directory in the file server and makes files as each program name into this folder.
Chapter 5 Network Viewer & Capture The setting window disappears and then the programs are listed on the window if there are program files at the login directory in the connected ftp server. Click New button. Enter a program name and click Add button. The folder selection window appears and select a folder in which the JPEG data are stored and then click Add button to register into the folder lists.
Use the web browser to access to the control page of the projector. Click Network Viewer on the main menu on the web page, then connect to the file server and select the program name which was made at previous section. The projector starts display- ing the images along the program.
Chapter 5 Network Viewer & Capture Using the Network Viewer function The Network Viewer is a function to acquire and project the JPEG image data on the screen from the file servers placed in the network. The projected image data are specified with the folder unit.
Select input mode to “Network” previously. Access to the control page on the projector by using the web browser. From the main menu, click Network Viewer to display the setting page. Setup the setting page  of the Visual Display. Host name ...Enter the name of ftp server, yourftp.server etc.
Chapter 5 Network Viewer & Capture Auto Display setting and control page  Auto Control ...Displays period (3 to 240 sec.), Repeating times (1 to 999 times) * 0 times represents endless dis- play The display status is indicated on the text area. Start...Starts automatic-image displaying End ...Quits automatic-image displaying Stop ...Stops automatic-image displaying...
Program New Registration  Click on “New Registration” linked text. Enter a program name and click Select button. On the Folder Selection window, click a folder and click Add button. Repeat the above for adding some another fold- ers. After finishing, click Close button. Check that the folder paths you added are listed on the text area.
Chapter 5 Network Viewer & Capture Program Confirmation & Change  Click on “Confirmation & Change” linked text. From “Program Name” pull-down menu button, select the program name you want to confirm or change. * Click Delete button to delete. * Click Select button to confirm or change the program.
 Control by the projector Select input mode to “Network” previously. Display the menu bar on the projected screen by pressing the MENU button on the projector or the remote control handset. Select “Network setting” icon by using the point but- tons (7/8) and press SELECT button once.
Chapter 5 Network Viewer & Capture...
Chapter 6 Controlling the Multi-Projectors Network Unit OWNER’S MANUAL...
Chapter 6 Controlling the Multi-Projectors Display the main menu following to the login procedure described on page 26. Multi-Control This function enables to control the multiple projectors equipped with the Network Units that are connected to the network at the same time. Click Multi Control on the main menu to display the control page.
Register IP address and projector name Click on Projector Registration to display the registration page. Type the IP address and projector name* and the click Register button. Check IP address and projector name To check the registered information, click on Confirmation & Change. The regis- tered information of the projector is listed as the right.
Chapter 6 Controlling the Multi-Projectors Exclude/Add/Delete a projector To change the mode of the registered pro- jectors, select a mode with the pull-down menu button under the IP address of the target projector and then click Set button. Mode Operation Control ...
Control Control Display the control page by clicking on Multi Control on the multi-control page. The setting pages are construct- ed from 1 to 6 page and each item is indicated on the next page. Load and apply the setting value The control sets saved for each projector ( p.54) can be used while the multi-con- trolled projectors function is being used.
Chapter 6 Controlling the Multi-Projectors Control multi-projectors at the same time The valid controls are shown below. Please refer to item “Control the Projector” p.40) for further control and description. When the control button or setting button is clicked, the registered projectors for the multi-control are controlled at the same time.
Chapter 7 Use of Serial Port Network Unit OWNER’S MANUAL...
Chapter 7 Use of Serial Port This product provides a serial control port (RS-232C) to control the external equipment which has an RC-232C port. This function allows external equip- ment to be controlled by the computer through the network and the projec- tor can be controlled by the external serial controller.
Setting for controlling the equipment connected to the serial port from the computer Serial Control :Selects “External” :Sets according to the com- Port puter specified port no. Do not use port no. 10000* :Sets according to the com- Other Settings munication condition of the equipment Setting for controlling the projector from the serial controller connect-...
Chapter 7 Use of Serial Port Control Examples Example 1 Controlling AV equipment through network Example 2 Controlling a projector which is not on the network function through network. Turn on the projector PJ1. Internet Intranet Turn on the DVD player and start playing.
Example 3 Controlling the projector with the serial controller through the serial port (RS-232C). Internet Intranet Use proper serial cable depending on the connected equipment port specification. Please refer to “Port Specification” of the serial port specification of this product ( Control Examples Serial controller RS-232C serial cable...
Chapter 7 Use of Serial Port Use of Telnet You can control the equipment connected to the serial port on the network unit and the projector itself by using the telnet application* following is a control example of external equipment. The telnet application is needed to use commands* which controls the external equipment.
When communication is established, the word “PASSWORD:” appears on the window. Type the login password* for the projector and then press “Enter” key on the keyboard. If you do not register the login password, just press “Enter” key. When the word “Hello” is replied, login has been succeeded. Type the commands from the key board to control the external equipment and then enter “Enter”...
Chapter 7 Use of Serial Port Control the projector with Telnet This product allows you to control the projector by using the Telnet application. Normally, it is used for controlling the external equipment connected to the serial port and also control the projector itself by specifying the telnet port no.10000. * It is not affected by the serial port setting of the projector when using the telnet appli- cation.
Chapter 8 Appendix:A Connection examples Web browser setting Technical data Network Unit OWNER’S MANUAL...
Chapter 8 Appendix Examples of Connection Peer-To-Peer connection Connecting the projector (PJ01) to the control computer (PC05) directly Projector Name: PJ01 IP Address : 192.168.0.2 Subnet Mask : 255.255.255.0 Default Gateway : 0.0.0.0 : 0.0.0.0 Connecting the projector (PJ01) to the control computer (PC05) via the hub. Projector Name: PJ01 IP Address : 192.168.0.2...
The gateway (Router) installed in the network Connecting the projector (PJ01) to the control computer (PC05) via the gateway. Meeting Room Projector Name: PJ01 IP Address : 192.168.200.15 Subnet Mask : 255.255.255.0 Default Gateway : 192.168.200.1 : 184.108.40.206 Network Group: 192.168.200.0 To another network Office Computer Name: PC05...
Chapter 8 Appendix Web browser setting This product is designed to enable the projector to be set up and controlled from an Internet web browser. Depending on the preference settings of the web browser, some control functions may not be available. Please make sure that the following functions are set up properly in the web browser.
Web browser setting Examples: OS/Browsers Windows XP Professional Internet Explorer v.6.0 ActiveScript setting Select the Internet Options menu from the Tool menu on the web browser and then select Security tab and click Customize Level… button. On the security setting win- dow, scroll down and find the Scripting item, make sure that “Enable”...
Chapter 8 Appendix Proxy setting Select the Internet Options menu from the Tool menu on the web browser and then select Connection tab and click LAN Settings button. Properly set up your web browser's the proxy server settings according to the local area network environment to which the projector is connected.
Chapter 8 Appendix Proxy setting Select the Preference menu from the Edit menu on the web browser and then select the item Advanced/Proxies in the Category column. Properly set up your web brows- er's the proxy server settings according to the local area network environment to which the projector is connected.
Product specification Type ...PJ-Net Organizer (Network Unit) LAN interface ...Applicant regulation IEEE802.3 (10Base-T) Network protocol ...TCP/IP specification Serial interface ...RS-232C Baud rate Flow control Parity check Terminal Power source ...Supplied from the projector Power consumption ...3.0 watts Dimensions (W x H x D)...5.39” x 1.18” x 4.33” (137 x 30 x 110mm) Weight ...0.34 lbs (155 g)
Chapter 8 Appendix Port Specification LAN port specification 8-pin modular connector (RJ-45) 1 2 3 4 5 6 7 8 pin No. Serial port specification D sub 9-pin connector (RS-232C) Pin No. Signal (not used) (not used) (not used) (not used) Signal Ground (not used)
Appendix:B Network Unit OWNER’S MANUAL...
Chapter 8 Appendix Installation/Access Why doesn’t the setting page appear in my web browser? Following causes are possible. Please check them. 1. The projector does not connect to the network. Check LED indicators status ( - Check the connection of LAN cable if the LINK indicator does not illuminate orange.
3. Enter the projector’s IP address [192.168.0.2] at “Address” column on the Web browser. [Note] Make sure that the proxy setting of your web browser is set “Not use a proxy server” ( 4. If the login page appears, this product is operating properly. The problems may be in the network configuration of the computer or in the network.
Chapter 8 Appendix How can I install several projectors equipped with the Network Unit? Install and configure network one by one to avoid the IP address collision each other ( p.21). To configure the IP address please see item “Network configuration” p.18).
Operation Why can't I change the controls in the setting page with web browser? Please make sure the projector is turned on. If it is in the standby mode, the setting is not effective to the projector. To control the projector with a web browser, the projector must be in the powered-on condition.
Chapter 8 Appendix Why am I not receiving E-mail alert messages? Make sure that the registered E-mail address and SMTP server address are cor- rect. If the SMTP server is located in your LAN (Local Area network), the address should be set to the SMTP server in your LAN. The SMTP server locat- ed outside of your LAN may not be available for security reason.
Can I update the firmware of the Network Unit. It is possible to update the firmware through the network. It is required to have a special tool for the updat- ing. For further information please consult your local dealer. The ver- sion number of the firmware is indi- cated on the lower part of the“Initial Setting”...
Chapter 8 Appendix What are the rules for IP address assignment? If the network is constructed with TCP/IP protocol, a unique IP address is required for each piece of network equipment. The following are basic rules of the assignment. Rule1 Do not configure the same IP address to the network equipment in the same network group.
Network Capture Why doesn’t the computer screen appear on the projected screen? 1. Make sure that the input mode of the projector is “Network”. 2. Make sure that the Network Capture icon on the task bar of the computer is active ( p.60).
Chapter 8 Appendix File Converter 1 What kind of image formats can I convert? The File Converter 1 enables to convert to the JPEG format from the following image format. Bitmap format (.bmp) JPEG format (.jpeg .jpg) File Converter 2 Sometime I have the white frame images converted by the File Converter 2.
Network Unit OWNER’S MANUAL...
Printed in Japan SANYO Electric Co. Ltd. 1AA6P1P3994-- (IDJW)