Download  Print this page

Makita 9020L Instruction Manual

Angle sander
Hide thumbs

Advertisement

INSTRUCTION MANUAL
No load speed
(RPM)
6,000
DOUBLE
INSULATION
Overall length
Net weight
Spindle thread
5 / 8 - 1 1 UNC
4.7 kg (10.4 lbsl
462 mm ( 1 8-3/16")

Advertisement

Table of Contents
loading

  Related Manuals for Makita 9020L

  Summary of Contents for Makita 9020L

  • Page 1 INSTRUCTION MANUAL DOUBLE INSULATION No load speed Overall length Net weight Spindle thread (RPM) 6,000 462 mm ( 1 8-3/16") 4.7 kg (10.4 lbsl 5 / 8 - 1 1 UNC...
  • Page 2: Important Safety Instructions

    IMPORTANT SAFETY INSTRUCTIONS (For All Tools) WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PERSONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries. CONSIDER WORK AREA ENVIRONMENT.
  • Page 3 14. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that keys and adjusting wrenches are removed from tool before turning 15. AVOID UNINTENTIONAL STARTING. Don't carry tool with finger on switch. Be sure switch is OFF when plugging in. 16.
  • Page 4 VOLTAGE WARNING: Before connecting the tool to a power source (receptacle. outlet, etc.) be sure the voltage supplied is the same as that specified on the nameplate of the tool. A power source with voltage greater than that specified for the tool can result in SERIOUS INJURY to the user as well as damage to the tool.
  • Page 5 ADDITIONAL SAFETY RULES FOR GRINDER 1. Keep guards in place. 2. Use only wheels having a maximum operating speed at least as high as "No Load RPM" marked on the tool's nameplate. When using depressed center wheels, be sure to use only fiberglass-reinforced wheels. 3.
  • Page 6 Installing side grip (auxiliary handle) Always install the side grip on the machine securely before operation. The side grip can be installed in any of three positions on the sides of the machine, whichever is con- venient and keeps the guard properly posi- Side grip tioned.
  • Page 7 Installing or removing abrasive disc CAUTION: Always be sure that the tool is switched off and unplugged before installing or removing the disc. NOTE: Use sander accessories specified in this manual. These must be purchased by separate. Mount the rubber pad onto the spindle. Fit the disc over the rubber pad and screw Lock nut...
  • Page 8 IF USED AS A GRINDER NOTE: Use grinder accessories specified in this manual. These must be purchased separately. WARNING: Always use guard assembly or accessory kit, noted below, for type 27 depressed center wheel. Guard assembly Part 192413-0 For 180 mm (7") 19") Part No.
  • Page 9 Installing or removing depressed center wheel CAUTION: Always be sure that the machine is switched Lock nut off and unplugged before installing or remov- ing the wheel. Depressed Mount the inner flange onto the spindle. Fit center whee the wheel over the inner flange and screw the lock nut onto the spindle.
  • Page 10 Switch action To start the tool, simply pull the trigger. Release the trigger to stop. For continuous operation, pull the trigger and then push in the lock lever. To stop the tool form the locked position, pull the trigger fully, then release Lock lever...
  • Page 11 Brush holder To maintain product SAFETY and RELIABILITY, repairs, any other maintenance or adjust- ment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts.
  • Page 12 ACCESSORIES CAUTION These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. The accessories or attachments should be used only in the proper and intended manner.
  • Page 13 743206-A 741413-3 (7,, 114, 718,,) 16') 743206-8 741 421-4 1/4" 7 / 6 7 (9" x @Flexible grinding wheel per pkg) (B) Makita zirconate per pkg) (mml Part N a Grit Size 741445-0 Part No. Grit Size (mml 741313-7A ,7,, (7"...
  • Page 14 ANGLE SANDER Model 9020L Note: The switch, noise suppressor and other part configurations may differ from country to country.
  • Page 15 MODEL 9020L Feb-03-'94 ITEM ITEM USED USED DEscWPTIDN DEsCRIPTON MACHINE Ball Bsannp 62MK)DW Ball Bserinp 6203DDW I"."l.tlgn w..her Bssnng Box Field Spmdle Baffle Plate Wwdruff Key 4 Pan Head Screw M S x l 6 IWith Washer1 ARMATURE ASSEMBCY (With Item 1, 2 h...
  • Page 16 MAKITA LIMrrED O N E YEAR WARRAECTY Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted be free of defects from worlananship and materials for the period of ONE YEAR from the date of original purchase.