TABLE OF CONTENTS Topic Page Inventory of Contents/ Additional Equipment 3 About WWVB Quick Set-Up Guide Detailed Set-Up Guide Battery Installation Program Mode Function Buttons Time Zone Setting DST (Daylight Saving Time) Setting Language Selection Time Setting Calendar Setting 12/24-Hour Setting Selecting °F or °C Features &...
2) Wait 15 minutes for WWVB reception. 3) If there is no WWVB reception, manually set the time and date (instructions in the Program Mode). 4) Program the settings. 5) Mount the WS-6002U in a suitable location, where WWVB signals can be received.
DETAILED SET-UP GUIDE I) BATTERY INSTALLATION Note: To avoid start-up problems make sure that the batteries do not spring free. Battery Compartment Battery Cover A) ATOMIC CLOCK 1) Remove the battery cover, located on the backside of the function buttons. 2) Observe the correct polarity, and install 2 AA batteries.
search after 10 minutes if the time is not found. When the search is cancelled “-:--”will appear in the time LCD. The Atomic Clock will conduct a WWVB search every hour until the first signal is found. Once the WWVB time is found, a search is automatically conducted nightly at midnight.
II) TIME ZONE SETTING 1) Hold down the “SET” button for 2 seconds, the default setting “-5EST” will flash in the Date LCD. 2) Press and release the “+” button to select the appropriate time zone. There are 13 time zones to choose from: -5EST Eastern Time (default setting) -6CST...
2) Press and release the “+” button to turn the DST off, as will be indicated by the display of “OFF” in the time LCD. 3) Press and release the “SET” button to confirm the DST setting, and to advance to select the language for the weekday. IV) LANGUAGE SELECTION FOR THE WEEKDAY 1) Hold down the “SET”...
VI) CALENDAR SETTING Note: When the WWVB signal is found, that date will over-ride the manually set date. 1) Hold down the “SET” button for 2 seconds (the selected time zone will flash), press the “SET” button 5 more times, until the default year “00”...
VIII) SELECTING °F OR °C 1) Hold down the “SET” button for 2 seconds (the selected time zone will flash), press the “SET” button 10 more times, until the default “°F” flashes in the time LCD. 2) Press and release the “+” button to toggle between °F and °C. 3) Press and release the “SET”...
MOUNTING Hanging Holes Function Buttons Foldout Table Stand There are two possible ways to mount the atomic clock: • use of the foldout table stand, or • wall mounting. I) FOLDOUT TABLE STAND The foldout table stand leg is located on the backside of the atomic clock.
Replace with new batteries only, and of recommended size. Opening the casings invalidates the warranty. Do not try to • repair the units. Contact La Crosse Technology for Repairs. TROUBLESHOOTING Problem: The LCD is faint. Solution: 1) Replace the batteries.
Problem: Hour is incorrect (minute and date are correct). Solution: 1) Be sure correct time zone and daylight saving time are selected. Note: For any questions not answered, contact La Crosse Technology with the contact information found at the end of this instructional manual. SPECIFICATIONS...
Warranty service can only be performed by a La Crosse Technology, Ltd authorized service center. The original dated bill of sale must be presented upon request as proof of purchase to La Crosse Technology, Ltd or La Crosse Technology, Ltd’s authorized service center.
Page 14
For warranty work, technical support, or information contact: La Crosse Technology, Ltd 2809 Losey Blvd. S. La Crosse, WI 54601 Phone: 608.782.1610 Fax: 608.796.1020 e-mail: support@lacrossetechnology.com (warranty work) sales@lacrossetechnology.com (information on other products) web: www.lacrossetechnology.com All rights reserved. This handbook must not be reproduced in any form, even in excerpts, or duplicated or processed using electronic, mechanical or chemical procedures without written permission of the publisher.