COOLING UNIT .............................................................................................................................................. 25
REPLACEMENT PARTS LIST ....................................................................................................................... 27
SERVICE MANUAL
REFRIGERATOR-FREEZER
MODELS
In the interests of user-safety (Required by safety regulations in some
countries) the set should be restored to its original condition and only
parts identical to those specified should be used.
SJ-P43N/43N SJ-P47N/47N SERVICE MANUAL S6516SE47ATUFT REFRIGERATOR-FREEZER MODELS SJ-P43N-SL SJ-43N-BE SJ-P47N-SL SJ-47N-BE In the interests of user-safety (Required by safety regulations in some countries) the set should be restored to its original condition and only parts identical to those specified should be used.
SJ-P43N/43N SJ-P47N/47N CAUTIONS AND INFORMATIONS In case of following troubles, the cause is not related with the failure of refrigerator. Please mention the correct way to the customer for the use of refrigerator when the repairing. 1. Some foods froze in the refrigerator compartment. Do not place food directly in front of cold air outlet.
SJ-P43N/43N SJ-P47N/47N DESIGNATION OF VARIOUS PARTS The names in parenthesis are the denominations used in the REPLACEMENT PARTS LIST. 1. Freezer temp. control knob 2. Freezer shelf(Freezer tray) 3. Ice cube maker 4. Ice cube box(Ice storage box) 5. Deodorizing unit 6.
SJ-P43N/43N SJ-P47N/47N DIMENSIONS OUTER DIMENSIONS AND CLEARANCE more than more than more than more than 1210 1: Not include the handle (Unit : mm) Fig. E-1(SJ-P43N,SJ-43N) more than more than more than more than 1210 1: Not include the handle (Unit : mm) Fig.
SJ-P43N/43N SJ-P47N/47N INNER DIMENSIONS The dimensions between shelves can be changed by setting the shelves on the other rails. (Unit: mm) Fig. E-3(SJ-P43N) (Unit: mm) Fig. E-4(SJ-43N)
SJ-P43N/43N SJ-P47N/47N WIRING DIAGRAM Be sure to replace the electrical parts with specified ones for maintaining the safety and performance of the set. Figure W-1. Wiring Diagram (SJ-P43N,P47N) Figure W-2. Wiring Diagram (SJ-43N,47N)
SJ-P43N/43N SJ-P47N/47N FUNCTIONS 1. ADJUSTABLE TEMPERATURE CONTROL (1) Temperature control of freezer Thermostat (senses freezer temperature) operates on ON/OFF switchover to control the compressor and cool air circulating fan , and allows the freezer temperature to keep at a suitable temperature. However adjust the freezer temp.
Page 15
SJ-P43N/43N SJ-P47N/47N 2. DEFROSTING (1) No defrosting operation is necessary (2) Where is melted frost brought No defrosting operation is necessary. 1. Melted frost is brought into the evaporating As this machine is so designed that a built-in pan at the back of the set and is evaporated evaporator cools air and a fan circulates cooled here by the heat of compressor.
Page 16
SJ-P43N/43N SJ-P47N/47N (4) As a reference to determine the causes of trouble, malfunction and phenomena are described below. Refer to the following when repairing. 1. Disconnection of defrost heater As off-cycle defrosting is performed, the defrosting time is extremely prolonged. Each time defrosting is started, the freezer temperature rises and a portion of ice and stored foods are melted.
Page 17
SJ-P43N/43N SJ-P47N/47N 5. PLASMACLUSTER (Only for SJ-P43N,P47N) (1) Plasmacluster is what thing. The ionizer inside the refrigerator will release cluster ions, which are collective mass of positive and negative ions, into the the freezer and refrigertor compartments. The cluster ions inactivate airborne fungus. Plasmacluster panel (2) Plasmacluster Panel 1.When the refrigerator will be operated, the Plasmacluster lamp of the...
SJ-P43N/43N SJ-P47N/47N ASSEMBLING PROCEDURES OF MAIN PARTS AND CAUTIONS CAUTION: DISCONNECT THE UNIT FROM THE POWER SUPPLY BEFORE ANY REPAIRING. 1. R-AIR GUIDER ASSEMBLY A-sealer ag1 Damper thermo. R air guider S Plasma holder A-sealer ag3 (Only for SJ-43N,47N) Ionizer-K A-sealer ag2 Dial sealer Plasma harness...
Page 19
SJ-P43N/43N SJ-P47N/47N (3) Fixing of the Ionizer-K.(Only for SJ-P43N,P47N) (3)-1 Connect Ionizer-K and connector of the lead wire. (3)-2 Insert Ionizer-K to Plasma holder. (3)-3 Insert the (3)-2 assembly to R air guider A. R air guider A Plasma harness Ionizer-K Connector should insert surely.
Page 20
SJ-P43N/43N SJ-P47N/47N 2. FAN LOUVER AND E.V COVER ASSEMBLY 2-1. How to remove the Fan louver Fan louver (1) Take out 2 screws. Claw (2) Insert the screwdriver into the air hole of the Fan Claw louver. (3) Press the Fan louver to the left side with the Screw screwdriver,and pull it toward yourself to take off the Fan louver.
Page 21
SJ-P43N/43N SJ-P47N/47N (2)-2 Insert the terminals of Lead EV-cover ass'y to (2)-4 Set Fan clamp to Propeller fan 100 and insert Fan motor. it to the shaft of Fan motor. (2)-3 Fix two Motor cushions to Fan motor, and set it at Fan motor holder A and B.
Page 22
SJ-P43N/43N SJ-P47N/47N (4) Inserting of pins After inserting, fix with vinyl tape. F-thermostat 2 (RED, inserted) Fan motor 1 , 5 Vinyl tape Defrost thermo. 3 (PINK) WIRE COLOR FOR FAN MOTOR Fuse 8 (WHITE) 100-110V : WHITE 127V : YELLOW 220-240V : BLUE Fuse 8 (BLACK) F-thermostat 6...
Page 23
SJ-P43N/43N SJ-P47N/47N (2) Replacement of Def. heater ass'y. 3. DEFROST HEATER (2)-1 Remove the center screw of Drain support al to take it off from the food liner. (1) Taking-out Evaporator (1)-1. Take out E.v cover ass'y (Fig. A-16). Drain support al Evaporator Screw Food liner convex part...
Page 24
SJ-P43N/43N SJ-P47N/47N (2)-4. Replace Def. heater ass'y with new one. (2)-7. Stick the longer wire to the Drain support by aluminum tape (2 pieces), and wind vinyl tape (2 pieces) to lead wires of Def. heater ass'y by aluminum tape as shown in Fig. A-25. Heater cover Note: Glass cloth tape part shall be both side of Drain support to protect the lead wire from damaged.
SJ-P43N/43N SJ-P47N/47N (3) Installing of Evaporator (3)-1. Install Evaporator as shown in Fig. A-16 in the reverse order of Fig. A-17. (3)-2. Correct the deformed fin. NOTE 1. When installing Evaporator, take care not to deform significantly and break the pipes. 2.
Page 26
SJ-P43N/43N SJ-P47N/47N Dryer Capillary tube Charge pipe Hot pipe Evaporator Charge pipe Compressor Suction pipe S.P. connector Eva-pan pipe Back condenser Figure C-2. Location From Eva-pan pipe ass’y to Back condenser In From Suction pipe From Back condenser out From Compressor to SP connector to Hot pipe to Discharge p connector...