Related Manuals for Jet EQUIPMENT & TOOLS “W” Series
Summary of Contents for Jet EQUIPMENT & TOOLS “W” Series
- Page 1 OPERATOR'S MANUAL “W” Series Premium Pallet Trucks JET EQUIPMENT & TOOLS, INC. P.O. BOX 1349 253-351-6000 A WMH Company Auburn, WA 98071-1349 Fax 800-274-6840 www.jettools.com e-mail jet@jettools.com M-140075 2/01...
-
Page 2: Warranty
JET’s expense, but if it is determined there is no defect, or that the defect resulted from causes not within the scope of JET’s warranty, then the user must bear the cost of storing and returning the product. This warranty gives you specific legal rights, and you have other rights, which vary, from state to state. -
Page 3: Warnings
Failure to comply with these warnings may result in personal injury and/or property damage. The specifications in this manual are given as general information and are not binding. JET Equipment & Tools reserves the right to effect, at any time and without prior notice, changes or alterations to parts,... -
Page 4: Table Of Contents
You will notice several important features about your JET Premium Pallet Truck. It features a 2- 7/8” lowered height, rounded fork tips and nylon entry/exit rollers to provide easy entry and exit of pallets. -
Page 5: Assembly
Assembly Note: Individual pallet trucks are assembled and ready to use. Pallet trucks purchased in crate quantities (6 units to a crate) require some assembly. Match the “letter” label on the handle assembly to the “letter” label on the frame, prior to assembly. Tools Required for Assembly: Hammer 3mm Hex Wrench... -
Page 6: Specifications
Specifications Model Stock # B (dxw) (dxw) PT-2036W 140070 20.5” 6.25” 36” 16.5” 7-3/4” 2-7/8” 7”x2” 2-7/8”x3-11/16” 47” PT-2042W 140071 20.5” 6.25” 42” 16.5” 7-3/4” 2-7/8” 7”x2” 2-7/8”x3-11/16” 47” PT-2048W 140072 20.5” 6.25” 48” 16.5” 7-3/4” 2-7/8” 7”x2” 2-7/8”x3-11/16” 47” PT-2736W 140073 27”... -
Page 7: Operation
Operation To raise the forks, push lever down and pump the handle to the desired height. To lower forks, pull lever up. The lever is spring loaded and will return to the neutral position. To freely move the handle, set the lever in the center neutral position. -
Page 8: O-Ring & Seal Kit Replacement
3. Remove screw (#83) and empty the oil into a suitable container. Pump handle until all oil has drained. 4. Pull out ram piston or plunger piston. 5. Remove pump cap (#66) for Piston 6. Remove all O-Rings & Seals. 7. -
Page 9: Troubleshooting
Troubleshooting Possible problems could arise in the operation of your hydraulic pallet truck. Their probable causes(s) and corrective action(s) follow: Condition Probable Causes Corrective Action Hydraulic unit does not lift Oil low in tank Make sure there is no oil leakage from valve and add oil Steel ball not seated in hydraulic Place the lever in the down... - Page 10 Parts List for the PT-2748W Premium Pallet Truck Index Part Description Size Qty. 1..PT2748W-01.....Handle Assembly Complete............. 1 2..PT2748W-02.....Spring Pin ............8x50mm ....1 3..PT2748W-03.....Bearing ................... 1 4..PT2748W-04.....Spring Pin ............5x35mm ....2 5..PT2748W-05.....Pressure Plate................. 1 6..PT2748W-06.....C-clip....................1 7..
- Page 11 Index Part Description Size Qty. 45..PT2748W-45.....Lowering Linkage ................1 46..PT2748W-46.....Chain ....................1 47..PT2748W-47.....Anchor chain ................... 1 48..PT2748W-48.....Pressure Roller ................1 49..PT2748W-49.....Pressure Roller Shaft ..............1 50..PT2748W-50.....Pivot Pin..................1 51..PT2748W-51.....Spring Pin ............4x30 ......2 52..
- Page 12 97..PT2748W-97.....Bearing Base................... 1 98..PT2748W-98.....Set Screw............M8x10 ...... 1 99..PT2748W-99.....Dust Boot ..................1 *Available only in the O-ring & Seal kit - PT2748W-94 **Available only in the Overload Valve Assembly - PT2748W-84...
-
Page 13: Parts Breakdown
Parts Breakdown... - Page 14 Parts Breakdown...
-
Page 15: Test Certificate
Pump Breakdown... - Page 16 JET EQUIPMENT & TOOLS, INC. 2415 West Valley Highway N Fax: 800-274-6840 A WMH Company P.O. Box 1349 Phone: 253-351-6000 www.jettools.com Auburn, WA 98071-1349 e-mail: jet@jettools.com...