Related Manuals for Jet JTX-2748A
Summary of Contents for Jet JTX-2748A
- Page 1 Operating Instructions and Parts Manual JTX-2748A Pallet Truck 427 New Sanford Road LaVergne, Tennessee 37086 Part No. M-141800 Ph.: 800-274-6848 Edition 2 04/2020 www.jettools.com Copyright © 2019 JET...
-
Page 2: Important Safety Instructions
1.0 IMPORTANT SAFETY INSTRUCTIONS WARNING – To reduce risk of injury: Read and understand the entire owner’s manual before using the pallet truck. Read and understand all warning and instruction labels on the truck. Do not place hands or feet under the pallet truck at any time. ... -
Page 3: Table Of Contents
Paint finish is powder-coated for superior protection of the underlying steel. In summary, your JET Pallet Truck is designed to offer consistent, long-term operation with minimal maintenance and service attention. If there are questions or comments, please contact your local supplier or JET. -
Page 4: Specifications
Polyurethane The above specifications were current at the time this manual was published, but because of our policy of continuous improvement, JET reserves the right to change specifications at any time and without prior notice, without incurring obligations. Figure 4-1... -
Page 5: Assembly (For Crate Quantity Purchases Only)
5.0 Assembly (for crate quantity purchases only) Note: The following illustrations may not show your exact model. Individual pallet trucks are assembled and ready to use. Pallet trucks purchased in crate quantities (6 units to a crate) require some assembly. A hammer and pliers are required. Match the “letter” label on the handle assembly to the “letter”... -
Page 6: Operation
After filling, reinstall plug, then bleed the pump may require specialized tools. You can locate (see sect. 8.3). the nearest authorized JET Service Center on our website: www.jettools.com. Lubricate pivot points on load wheel frames, as needed. Do not get oil directly on load Numbers in parentheses refer to index wheels. - Page 7 Remove all O-Rings & Seals. Insert new O-Ring or Seal one at a time making sure to replace with the same size that was removed. (Order appropriate JET seal kit.) Re-assemble. Refill oil to bottom of fill hole with hydraulic jack oil.
-
Page 8: Troubleshooting Ptw-A Series Pallet Trucks
8.0 Troubleshooting PTW-A Series Pallet Trucks Any disassembly of the pallet truck should be done by qualified personnel. Contact Jet technical service if further assistance is needed. Trouble Probable Cause Remedy Make sure there is no oil leakage Low oil level in reservoir. -
Page 9: Jtx-A Pallet Truck - Exploded View
10.1 JTX-A Pallet Truck – Exploded View... -
Page 10: Jtx-A Pallet Truck - Parts List
10.2 JTX-A Pallet Truck – Parts List Index No. Part No. Description Size 101A ..PTWA101A ....Handle Body Assembly (#101 to 112) ............. 1 101 ... PTWA101 ....Handle Body..................... 1 102 ... PS063000 ....Roll Pin ..............Ø6x30 mm ....1 103 ... - Page 11 424 ... PTWA424 ....Nut ......................1 ....LM000413 ....Warning Label (not shown) ..............1 ....JTX2748A-ID ... I.D. Label, JTX-2748A (not shown) ............1 ....JTX2748A-SL ... Specification Label, JTX-2748A (not shown) ........... 1 ....
-
Page 12: Warranty And Service
JET sells through distributors only. The specifications listed in JET printed materials and on official JET website are given as general information and are not binding. JET reserves the right to effect at any time, without prior notice, those alterations to parts, fittings, and accessory equipment which they may deem necessary for any reason whatsoever.