Table of Contents
Advertisement
Quick Links
™
Hardware User Manual
Core 1000 – Centralized audio and control processor
Core 3000 – Centralized audio and control processor
Core 4000 – Centralized audio and control processor
I/O Frame – Networked audio and control input and output device
TD-000282-00-A
*TD-000282-00*
Advertisement
Table of Contents
Related Manuals for QSC Q-SYS Core 3000
Summary of Contents for QSC Q-SYS Core 3000
- Page 1 ™ Hardware User Manual Core 1000 – Centralized audio and control processor Core 3000 – Centralized audio and control processor Core 4000 – Centralized audio and control processor I/O Frame – Networked audio and control input and output device TD-000282-00-A *TD-000282-00*...
-
Page 2: Important Safety Precautions And Explanation Of Symbols
O: 表明这些有毒或有害物质在部件使用的同类材料中的含量是在 SJ/T11363_2006极限的要求之下。 QSC Audio Products, LLC guarantees its products to be free from defective material and/or workmanship for a period of three (3) years from the date O: Indicates that this toxic or hazardous substance contained in all of the homogeneous materials for this part is below the limit requirement in SJ/ of sale and will replace defective parts and repair malfunctioning products under this warranty when the defect occurs under normal installation and T11363-2006. - Page 3 Insert the molded receptacle of the AC power cord into the AC power inlet on the (use a strong box of appropriate size, sufficient packing/padding material to prevent load shifting or impact damage) or call QSC’s Technical Services Group for replacement packing material and a carton.
- Page 4 Minimum System Requirements for Q-Sys™ Designer Quick Start Guide Q-Sys Designer is the software with which you create the designs for a Q-Sys system. After the system is designed, tested and deployed on the Core, This is intended to give a high-level procedure for getting a simple Q-Sys system connected, running a Q-Sys design, and passing audio. The following Q-Sys designer is not required for that system to operate.
- Page 5 Components QSC DataPort amplifiers (PowerLight™, CX, PL2, DCA, and PL3) can be used in a Q-Sys system to communicate with the Q-Sys DataPort card and provides critical telemetry information and protection for both the amplifier and any QSC loudspeaker. Generic amplifiers can be used in a Q-Sys Q-Sys is comprised of the following dedicated components: system by connecting the amplifier to a Line Out connection;...
- Page 6 DataPort I/O Cards. Note that the Q-Sys hardware products are configured at the QSC factory per the customer’s order. At the time of order, the customer specifies the Note that the Q-Sys hardware products are configured at the QSC factory per the customer’s order. At the time of order, the customer specifies the type of Q-Sys Audio I/O Card to be populated in rear panel audio I/O bay on the Q-Sys Core 1000, Core 3000 and Core 4000 products.
- Page 7 Q-Sys™ I/O Card Install/Uninstall Procedure Qualified Ethernet Switches Card installation should only be done by a trained and qualified technician. Q-Sys uses layer 3 (DSCP) QoS. This type of QoS is deployed differently on different networks and therefore requires user intervention to set up properly.
- Page 8 Front Panel Controls LCD page forward momentary switch LCD page forward momentary switch 48V phantom power 48V phantom power equipped QSC amplifiers and high performance Unit ID button momentary switch Unit ID button momentary switch pre-amplifiers and A/D Clear settings momentary switch...
-
Page 9: Mailing Address
© 2009 QSC Audio Products, LLC. All rights reserved. QSC, the QSC logo and PowerLight are registered trademarks of QSC Audio Products, LLC in the U.S. Patent and Trademark office and other countries. Q-Sys and Intrinsic Correction are trademarks of QSC Audio Products, LLC. AMD is a trademark of Advanced Micro Devices, Inc. Apple is a trademark of Apple, Inc. Cisco is a trademark of Cisco Systems, Inc.