Table of Contents
Advertisement
.-4415
Powerheads
Model Number: Description:
DDSKAV15
Dual Drive w/ 15HP Kawasaki
DDSKAV15CE
Dual Drive w/ 15HP Kawasaki (Export)
DDSKAV17
Dual Drive w/ 17HP Kawasaki
DDSKAV17CE
Dual Drive w/ 17HP Kawasaki (Export)
DDSKAV23
Dual Drive w/ 23HP Kawasaki
DDSKAV23CE
Dual Drive w/ 23HP Kawasaki (Export)
Ferris Industries
5375 North Main Street
Munnsville, NY 13409
800-933-6175
HydroWalk Series
Dual Drive Walk-Behind Mowers
OPERATOR'S
MANUAL
48" Mower Decks
Model Number: Description:
DDS48
48" Mower Deck
DDS48R
48" Rear Discharge Mower Deck (Export)
52" Mower Decks
Model Number: Description:
DDS52
52" Mower Deck
DDS52R
52" Rear Discharge Mower Deck (Export)
DDSH52
52" E-Z Adjust Mower Deck
61" Mower Decks
Model Number: Description:
DDS61
61" Mower Deck
DDSH61
61" E-Z Adjust Mower Deck
22880
Rev. 01/2002
TP 100-7056-00-WD-F
Advertisement
Table of Contents
Troubleshooting
Related Manuals for Ferris Hydrowalk Series DDSKAV15CE
Summary of Contents for Ferris Hydrowalk Series DDSKAV15CE
- Page 1 Dual Drive w/ 17HP Kawasaki DDSKAV17CE Dual Drive w/ 17HP Kawasaki (Export) DDSKAV23 Dual Drive w/ 23HP Kawasaki DDSKAV23CE Dual Drive w/ 23HP Kawasaki (Export) Ferris Industries 5375 North Main Street Munnsville, NY 13409 800-933-6175 OPERATOR’S MANUAL 48” Mower Decks...
- Page 2 This warranty shall apply ONLY if the warranty registration form has been completed and returned to Ferris Industries, Inc. within 20 days from the date of delivery. Ferris Industries, Inc. (Ferris) warrants, in accordance with the provisions below, to the original purchaser for the period of twenty-four (24) months from the date of delivery of a Ferris mower that the mower is free from defects in material or workmanship.
-
Page 3: Table Of Contents
NOTE: In this manual, “left” and “right” are referred to as seen from the operating position. WARNING Engine exhaust from this product contains chemicals known, in certain quantities, to cause cancer, birth defects, or other reproductive harm. © Copyright 2002 Ferris Industries All Rights Reserved. Printed in USA. TP 100-7056-00-WD-F... -
Page 4: Identification Tags
Authorized Dealer for replacement parts, service, or information YOU MUST HAVE THESE NUMBERS. North American Models FERRIS FERRIS FERRIS INDUSTRIES, INC. FERRIS INDUSTRIES, INC. MUNNSVILLE, NY 13409 MUNNSVILLE, NY 13409 MADE IN THE USA MADE IN THE USA MODEL NO. -
Page 5: Safety Rules & Information
Read these safety rules and follow them closely. Failure to obey these rules could result in loss of con- trol of unit, severe personal injury or death to you, or bystanders, or damage to property or equipment. This mowing deck is capable of amputating hands and feet and throwing objects. The triangle in text signifies important cautions or warnings which must be followed. -
Page 6: Operation
Safety Rules & Information OPERATION • Never run an engine in an enclosed area. • Mow only in the daylight or with good artificial light, keeping away from holes and hidden hazards. • Be sure all drives are in neutral and parking brake is engaged before starting engine. -
Page 7: Children
CHILDREN Tragic accidents can occur if the operator is not alert to the presence of children. Children are often attracted to the unit and the mowing activity. Never assume that chil- dren will remain where you last saw them. • Keep children out of the mowing area and under the watchful care of another responsible adult. -
Page 8: Decals
Safety Decals GENERAL This unit has been designed and manufactured to pro- vide you with the safety and reliability you would expect from an industry leader in outdoor power equipment manufacturing. Although reading this manual and the safety instructions it contains will provide you with the necessary basic knowledge to operate this equipment safely and effec- tively, we have placed several safety labels on the unit to remind you of this important information while you are... -
Page 9: Ce Compliance Specs
CE Compliance Specs... -
Page 10: Features & Controls
Features & Controls of the Dual Drive Walk-Behind Please take a moment and familiarize yourself with the name, location, and function of these controls so that you will better understand the safety and operating instructions provided in this manual. A. Forward Speed Control Lever B. -
Page 11: Safety Interlock System
D. Parking Brake Handle The parking brake is applied by pushing DOWN on the parking brake handle until it stops. To release the park- ing brake, pull UP on the handle until it locks over cen- ter. E. PTO (Power Take Off) Switch The PTO switch engages and disengages the mower. -
Page 12: Operating The Dual Drive Walk-Behind
Operating the Dual Drive Walk-Behind GENERAL OPERATING SAFETY Before first time operation: • Be sure to read all information in the Safety and Operation sections before attempting to operate this tractor and mower. • Become familiar with all of the controls and how to stop the unit. -
Page 13: Starting The Engine
WARNING If you do not understand how a specific control functions, or have not yet thoroughly read the FEATURES & CONTROLS section, do so now. Do NOT attempt to operate the tractor without first becoming familiar with the location and function of ALL controls. -
Page 14: Mowing
Operating the Dual Drive Walk-Behind MOWING Before mowing, set the cutting height as described in the Troubleshooting, Adjustments & Service section. 1. Engage the parking brake. Make sure the PTO switch is disengaged and the motion control lever is in the NEUTRAL position. 2. -
Page 15: Storage
STORAGE Temporary Storage (30 Days Or Less) Remember, the fuel tank will still contain some gasoline, so never store the unit indoors or in any other area where fuel vapor could travel to any ignition source. Fuel vapor is also toxic if inhaled, so never store the unit in any structure used for human or animal habitation. -
Page 16: Regular Maintenance
Regular Maintenance MAINTENANCE SCHEDULE & PROCEDURES The following schedule should be followed for normal care of your mower. You will need to keep a record of your operating time. SAFETY ITEMS Check Safety Interlock System Check Mower Blade Stopping Time NORMAL CARE ITEMS Check Rider/Mower for loose hardware Check Engine Oil Level... -
Page 17: Checking/Adding Fuel
CHECKING / ADDING FUEL To add fuel: 1. Remove the fuel cap (see A, Figure 2). 2. Fill the tank to the bottom of the filler neck. This will allow for fuel expansion. NOTE: Do not overfill. Refer to your engine manual for specific fuel recommendations. -
Page 18: Lubrication
Regular Maintenance LUBRICATION Lubricate the machine at the lubrication points shown in Figures 6 - 11. Use grease fittings when present. Disassemble parts to apply grease to moving parts when grease fittings are not installed. Not all greases are compatible. Ferris Red Grease (P/N 22285) is strongly recommended. -
Page 19: Battery Maintenance
BATTERY MAINTENANCE Checking the Battery Fluid NOTE: It is not necessary to check the battery fluid level if machine is equipped with a maintenance-free battery. 1. Remove the battery box cover to access the battery. 2. Remove the battery filler cap(s) (A, Figure 12). Fluid must be even with the split ring full mark. -
Page 20: Servicing The Mower Blades
Regular Maintenance SERVICING THE MOWER BLADES 1. Blades should be sharp and free of nicks and dents. If not, sharpen blades as described in following steps. 2. Remove the deck guard. 3. Raise the mower deck and secure with jackstands. 4. -
Page 21: Troubleshooting The Mower
TROUBLESHOOTING While normal care and regular maintenance will extend the life of your equipment, prolonged or constant use may eventually require that service be performed to allow it to continue operating properly. The troubleshooting guide below lists the most common problems, their causes and remedies. -
Page 22: Troubleshooting The Mower Deck
Troubleshooting, Adjustment & Service Rider Troubleshooting Continued. PROBLEM Engine runs, but mower will not drive. Transmission drive belt slips. Brake will not hold. Mower steers hard or handles poorly. TROUBLESHOOTING THE MOWER DECK PROBLEM Mower cut is uneven. Mower cut is rough looking. Engine stalls easily with mower engaged. -
Page 23: Mowing Height Adjustment
MOWING HEIGHT ADJUSTMENT The mowing height is determined by three factors: the mount position of the mower deck, the number of blade spacers above the spindle and the number of caster spacers above the caster arm. Refer to the Height Of Cut chart to the right for the cor- rect settings to obtain the desired height of cut. -
Page 24: Deck Leveling Adjustment (Ddsh Models)
Troubleshooting, Adjustment & Service DECK LEVELING ADJUSTMENT (DDSH Models only) 1. Make sure there is one spacer above and below the frame on the front caster shafts and place hairpin clips in the 2” cutting height position (see Figure 17). 2. -
Page 25: Mowing Height Adjustment (Ddsh Models)
Shimming the Hanger Shafts Once it has been determined that a shim (P/N 20928) is required, you first must determine which rear hanger shaft requires the shim. The shim (A, Figure 20) must be placed in between the spacer (B, Figure 20) and the retaining collar (C, Figure 20) on the OPPOSITE side from which the front shaft has movement or slack (see Figure 21). -
Page 26: Mower Belt Replacement
Troubleshooting, Adjustment & Service MOWER BELT REPLACEMENT AND ADJUSTMENT To avoid damaging belts, DO NOT PRY BELTS OVER PULLEYS. PTO Clutch to Deck Belt 1. Park the machine on a smooth, level surface such as a concrete floor. Disengage the PTO, engage the parking brake, turn off the engine, and remove the ignition key. -
Page 27: Mower Belt Replacement (Ddsh Models)
MOWER BELT REPLACEMENT AND ADJUSTMENT (DDSH Models only) To avoid damaging belts, DO NOT PRY BELTS OVER PULLEYS. 1. Park the machine on a smooth, level surface such as a concrete floor. Disengage the PTO, engage the parking brake, turn off the engine, and remove the ignition key. -
Page 28: Transmission Drive Belt Replacement
Troubleshooting, Adjustment & Service TRANSMISSION DRIVE BELT REPLACEMENT To avoid damaging belts, DO NOT PRY BELTS OVER PULLEYS. 1. Remove the deck drive belt. See MOWER BELT REPLACEMENT AND ADJUSTMENT sections. 2. Remove the grass screen that covers the transmis- sion cooling fans. -
Page 29: Transmission Neutral & Tracking Adjustments
TRANSMISSION NEUTRAL & TRACKING ADJUSTMENTS Neutral Adjustment 1. Park the machine on a smooth, level surface such as a concrete floor, away from bystanders and prefer- ably facing a wall. Disengage the PTO, engage the parking brake, turn off the engine, and remove the ignition key. -
Page 30: Transmission Maintenance & Service
Troubleshooting, Adjustment & Service TRANSMISSION MAINTENANCE AND SERVICE The hydrostatic transmissions are sealed units that require no maintenance other than the following. • Keep the grass screen and transmission cooling fins clear or grass, leaves and debris. • Keep oil level in the reservoirs (A, Figure 30) at the “FULL”... -
Page 31: Pto Clutch Adjustment
Figure 32. PTO Clutch Adjustment Adjustment Window (Qty. 3, one shown) Adjustment Nut PTO CLUTCH ADJUSTMENT Check the PTO clutch adjustment after the initial 50 hour break-in period and then after every 250 hours of opera- tion. Also perform the following procedure if the clutch is slipping or will not engage, or if a new clutch has been installed. -
Page 32: Battery Service
Troubleshooting, Adjustment & Service BATTERY SERVICE WARNING Keep open flames and sparks away from the battery; the gasses coming from it are highly explosive. Ventilate the battery well during charging. Checking Battery Voltage A voltmeter can be used to determine condition of bat- tery. - Page 33 THIS HOOK-UP FOR NEGATIVE GROUND VEHICLES Starter Switch Starting Vehicle Battery To Ground MAKE CERTAIN VEHICLES DO NOT TOUCH Figure 34. Jump Starting WARNING Any procedure other than the preceding could result in: (1) personal injury caused by electrolyte squirting out the battery vents, (2) personal injury or property damage due to battery explosion, (3) damage to the charging system of the...
-
Page 34: Replacement Parts & Accessories
Common Replacement Parts & Accessories COMMON REPLACEMENT PARTS Listed below are parts numbers for the more common replacement parts. Use only genuine Ferris replace- ment parts to assure optimum performance and safety. 48” Deck Belt (PTO to Spindle)...21723 48” Deck Belt (Spindle) ...20873 48”... -
Page 35: General Information
GENERAL INFORMATION Proper mowing is an important part of maintaining your lawn in the best possible condition. A healthy and well maintained lawn is better able to resist drought, weeds, and other stresses. But too much maintenance is as detrimental to your lawn as neglect. Proper care for your lawn involves more than just “cutting the grass.”... -
Page 36: Lawn Care & Mowing Information
Lawn Care & Mowing Information HOW HIGH TO MOW THE GRASS Often cutting height is a matter of personal prefer- ence. Typically, you should mow the grass when it is is between three and five inches high. The proper cutting height range for a specific lawn will depend upon several factors, including the type of grass,... -
Page 37: When And How Often To Mow
WHAT MOWING PATTERNS TO USE Always start mowing on a smooth, level area. The size and type of area to be mowed will determine the best mowing pattern to use. Obstructions such as trees, fences and buildings, and conditions such as slopes and grades must also be considered. -
Page 38: Mowing Methods
Lawn Care & Mowing Information MOWING METHODS Proper Broadcast Mowing Broadcasting, or side-discharging, disperses fine clip- pings evenly over the entire lawn. Many golf courses use this method. Your mower has a deep dish deck to allow freer circulation of clippings so they are broadcast evenly over the lawn. - Page 39 TIPS On Dealing With Clippings Clippings are beneficial to your lawn. A common mis- conception about clippings is that they automatically lead to thatch—this is untrue. Short clippings produced by broadcasting and clippings produced by mulching methods actually contribute to a healthy lawn because they: COMPOSTING The best way to recycle excess clippings and leave your...
- Page 40 Lawn Care & Mowing Information SOLUTIONS FOR COMMON MOWING PROBLEMS Streaking Streaking is when thin strips of uncut grass are left behind the mower. Streaking is usually caused by operator error or poor blade maintenance. CAUSE Blades are not sharp Blades are worn down too far Engine speed is too slow Ground speed is too fast...
- Page 41 Uneven Cutting Uneven cutting is waviness or smooth troughs in the lawn surface. Uneven cutting is usually caused by mower deck damage or misadjustment. CAUSE Deck is not leveled correctly Blades are dull or worn Blades are damaged Deck is clogged with grass clippings Deck shell is damaged Mower spindle is bent or loose Blades are installed incorrectly...
-
Page 42: International Symbols
Common International Symbols Choke Fast (Throttle) Slow (Throttle) Throttle Fuel Technical Manuals Additional Technical Literature Available Operators Manuals Additional copies of this manual are available, (and as part of our product support commitment, we maintain a stock of printed operators manuals going back many years!) Parts Manuals Fully illustrated parts manuals are also available —... - Page 43 Notes LC-9...