Genelec 1091A Operating Manual page 4

1091A SYSTEM SPECIFICATIONS 1091A SYSTEM SPECIFICATIONS
1091A SYSTEM SPECIFICATIONS 1091A SYSTEM SPECIFICATIONS 1091A SYSTEM SPECIFICATIONS
Free field frequency response of system (± 2.5 dB):
Maximum short term sine wave acoustic output in half space,
averaged from 45 Hz to 80 Hz @ 1m:
Self generated noise level in free field @ 1m on axis (A-weighted)
Harmonic distortion at 95 dB SPL @ 1m on axis in
half space (40...85 Hz):
Driver:
Weight:
Dimensions:
FILTER SECTION FILTER SECTION
FILTER SECTION FILTER SECTION FILTER SECTION
Lowpass filter above 85 Hz:
Subsonic filter below 40Hz
Crossover frequency, (sub/main monitors)
Mid Band Rejection frequency > 400 Hz:
Level control operating range in -2 dB steps
Genelec Oy, Olvitie 5 Genelec Oy, Olvitie 5
Genelec Oy, Olvitie 5 Genelec Oy, Olvitie 5 Genelec Oy, Olvitie 5
FIN - 74100 IISALMI, FINLAND FIN - 74100 IISALMI, FINLAND FIN - 74100 IISALMI, FINLAND FIN - 74100 IISALMI, FINLAND FIN - 74100 IISALMI, FINLAND
Phone: Phone: Phone: +358 17 83881 +358 17 83881 +358 17 83881
Phone: Phone: +358 17 83881 +358 17 83881
Telefax: Telefax: Telefax: Telefax: Telefax: +358 17 812267 +358 17 812267 +358 17 812267 +358 17 812267 +358 17 812267
Web: Web: http://www.genelec.com http://www.genelec.com
Web: Web: Web: http://www.genelec.com http://www.genelec.com http://www.genelec.com
E-mail: E-mail: E-mail: E-mail: E-mail: genelec@genelec.com genelec@genelec.com genelec@genelec.com genelec@genelec.com genelec@genelec.com
AUDIO PRECISION1091A LEVEL(dBr)
100
95
90 1029A + 1091A
RESPONSE
1091A RESPONSE
85
1029A BASS
ROLL-OFF - 6dB
80
SW 2 'ON'
75
70
65
60
55
50
20 100
38 - 85 Hz
>103 dB SPL
< 10 dB
< 3%
210 mm
( 8")
10.2 Kg
(22.4 lb)
7
Height 505 mm (19 / ")
8
7
Width 251 mm (9 / ")
8
Depth 230 mm (9")
24 dB/Octave
18 db/Octave
85 Hz
> 50 dB
from 0 to -8 dB
(Reference to 1029A output)
vs FREQ(Hz) 23 SEP 96 10:44:21
1029A RESPONSE
1k
AMPLIFIER SECTION AMPLIFIER SECTION
AMPLIFIER SECTION AMPLIFIER SECTION AMPLIFIER SECTION
Amplifier output power :
(Long term output power is limited by driver
unit protection circuitry.)
Amplifier system distortion at nominal output:
Signal to Noise ratio, referred to full output:
Mains voltage:
Voltage operating range:
Power consumption (average):
INPUT SECTION INPUT SECTION
INPUT SECTION INPUT SECTION INPUT SECTION
Input connectors XLR & ¼"
Input impedance:
Input level for 100dB SPLoutput @ 1m in full space:
10k 20k
THD
SMPTE-IM < 0.08%
CCIF-IM
DIM 100
100/200 or 115/230V
Idle
Full output
XLR female ¼" Jack
pin 1: gnd
pin 2: +
pin 3: -
2 x 33 kΩ balanced.
variable from -23dBu to
-15 dBu in 2dB steps.
Data Sheet No. 1091-0106-1 Data Sheet No. 1091-0106-1 Data Sheet No. 1091-0106-1 Data Sheet No. 1091-0106-1 Data Sheet No. 1091-0106-1
COPYRIGHT GENELEC OY 1996 COPYRIGHT GENELEC OY 1996 COPYRIGHT GENELEC OY 1996 COPYRIGHT GENELEC OY 1996 COPYRIGHT GENELEC OY 1996
All data subject to change without prior notice All data subject to change without prior notice All data subject to change without prior notice
All data subject to change without prior notice All data subject to change without prior notice
70 W (16 Ω)
< 0.08%
< 0.08%
< 0.08%
> 90 dB
± 10%
9 VA
100 VA
sleeve
tip
ring