Housing for nikon coolpix s210 digital camera (21 pages)
Summary of Contents for Fantasea Nano Focus Light
Page 1
Fantasea Nano Focus Light (Cat. No. 6022) Instruction Manual The Fantasea Nano Focus Light is a high intensity ultra compact underwater LED light. It was designed as a modeling light and in order to better enable the camera auto focus, especially when photographing in low light conditions. The Nano Focus Light features a dim‐out sensor which automatically shuts off the LED light whenever a camera pre‐flash is fired, thereby eliminating a hotspot in the image, caused by the beam of the light. Nano Focus Light Specifications 8 x Super Bright LED bulbs Luminance: 18,000 mcd Bulb Life: 10,000 hours Light color: 7500K Uses 4 x AAA batteries Burn Time: up to 8 hours per set of batteries Weight: 60g Dimensions: 36 x 133mm / 1.4 x 5.2 inch (Diameter x Length) Includes a Y‐S mount Color: Black Depth ratio: 100 meters / 330 feet ...
Page 2
Y‐S Connector Hand Lanyard Dim‐Out Sensor Instructions for Use A. Installing & Removing Batteries a. To open the Nano Focus Light, hold the hand grip firmly in one hand and turn the flashlight head counterclockwise until it separates. Pull the flashlight head off. Please make sure that the light is pointed in an upward position so the contents do not fall out when opened. Take special care not to stare into the light beam which is very powerful and could damage your eyes. b. Gently remove the LED head by pulling it out. c. Install or remove 4 AAA Alkaline batteries. Please note that this light should not be used with rechargeable batteries. Make sure to follow the instructions diagram printed on the interior of the light. Note that there are two sets of two batteries, each set pointing towards a different direction. d. Replace the LED head carefully, making sure that the two protrusions on the inside of the battery compartment correspond with the two niches on the LED head. This is the only way it will fit properly. e. Carefully place the flashlight head over the threads, and tighten evenly in a clockwise fashion. Do not use force and do not allow it to screw down unevenly. Take special care not to stare into the light beam which is very powerful and could damage your eyes. Fantasea Nano Focus Light Instruction Manual 20110120...
Page 3
C. Mounting the Nano Focus Light on an Arm a. Remove the screw from the Y‐S Connector at the bottom of the Nano Focus Light by unscrewing it all the way out. b. Position the Nano Focus Light over the arm so that the Y‐S Mount on top of the arm is aligned with the Y‐S Connector at the bottom of the focus light. c. Install the screw all the way through the focus light and arm connectors. Tighten it enough to keep the focus light in a fixed position. D. Using the Nano Focus Light a. You can keep the Nano Focus Light turned on during the dive, as it features a burn time of approx. 8 hours per set of batteries. b. During the dive, tilt the focus light mounted on the arm, so that it is pointing at your subject. This will allow for the camera to easily focus on the subject, even when photographing in low light conditions, ensuring your image turns out focused and sharp. c. Once the camera has focused, push the shutter release button all the way down to take the image. The Nano Focus Light dim‐out sensor will automatically shut off the light for a second when the camera pre‐flash is emitted. This will prevent a hotspot in your image caused by the beam of the light. d. After a second, the Nano Focus Light will automatically turn back on. E. Care & Maintenance a. After each dive, carefully soak and rinse exterior components in fresh water. b. Store the Nano Focus Light in a protected, dry and shaded area. Fantasea Nano Focus Light Instruction Manual 20110120...
Page 4
Period”). This warranty does not cover any commercial use of the product. If a product defect arises and a valid claim is received within the Warranty Period, at its option, Fantasea, or its authorized service facilities will either (1) repair the product defect at no charge, (2) exchange the product with a product that is new or which has been manufactured from new or serviceable used parts and is at ...