Installingthe Hood - Electrolux FHWC3060LSA Use & Care Manual

Installing the hood ,,!!!"7
• Flexible metal round ducts should only be used /_g.
when no other duct fitting exists Limit use to iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii
" _ iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii
short lengths and do not crush when making :::_-- _: opening for ductwork iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii
corners. .--:---f _ __
_'_---_: iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii
-\::_-: iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii
ViewFrom Rear iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii
Examples
of possible ducting
or air
IC_ats'
iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii
reoirou_ation _ iiiiiiiiii
iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii
"°®
iiiiiiiiiiiiiiiiiiiiiii
Rodpitch with Sidewall cap Recirculator 1"x6"Min. iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii
flashing and cap Mounting iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii
_...i..(_ /. .... .' j_. ::
Support iiiiiiiiiiiiiiiiiii
.... ..... ..... --- . ..... ..... "_- _---_:_ iiiiiiiiiiiiiiiiiiiiiiiiiii
_ _ _ iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii
i_ " ............... :-..:-) ;i'/_ )"1 !!!!!!!!!!!!!!!!!!!!!!!!
_- iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii
Pi Pipe Pipe iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii
r_ L Centerline iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii
co,_rL co,_ co,_ iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii
2_
Space iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii
iiiiiiiiiiiiiiiiiiiiiiiiiii
iiiiiiiiiiiiiiiiiiii
iiiiiiiiiiiiiiiiiiiiiiiiiiiiii
Installing range hood to the wall
(Exhaust operation)
Install framing for hood support
• If drywall is present, mark the screw hole
locations.
• Cut away enough drywall to expose 2 vertical
studs at the holes location indicated by the
template. Install two horizontal supports at least
1" x 6" between two wall studs at the bottom and
top mounting holes installation location (fig. (_)).
• The horizontal support must be flush with the
room side of the studs. Use cleats behind both
sides of the support to secure to wall studs.
• Reinstall drywall and refinish.
Step 1:
"
Make sure that no cables or pipes will become __,
damaged(e.g, electric, gas, water;testtheareas
inquestionwithacabledetector), iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii
• Using supplied template (17), mark and drill 8
holes in the wall. Drill the holes according tothe
measureddistancesfromthediagram(fig. Q). iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii
• Upper/Lower bracket (4, 5): Insert 4 wall plugs
(11) intothe4drilled holes, iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii
• Rangehood(1):lnstallationisdependingonwall iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii
type: iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii
w_,_,pe _e_o_ed_te,,e_ iii
Wood Nowall plugs(11) iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii
required iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii
Brick/Concrete 4wallplugs(11) iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii