Page 3 Preface Notice The company reserves the right to revise this publication or to change its contents without notice. Information contained herein is for reference only and does not constitute a commitment on the part of the manufacturer or any subsequent vendor. They assume no responsibility or liability for any errors or inaccuracies that may appear in this publication nor are they in anyway responsible for any loss or damage resulting from the use (or misuse) of this publication.
Page 4: Fcc Statement
Preface FCC Statement (Federal Communications Commission) You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
Page 5: Fcc Rf Radiation Exposure Statement
Preface FCC RF Radiation Exposure Statement: This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body.
Page 6: Important Safety Instructions
Preface IMPORTANT SAFETY INSTRUCTIONS Follow basic safety precautions, including those listed below, to reduce the risk of fire, electric shock, and injury to persons when using any electrical equipment: Do not use this product near water, for example near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet basement or near a swimming pool.
Page 7: Instructions For Care And Operation
Preface Instructions for Care and Operation The computer is quite rugged, but it can be damaged. To prevent this, follow these suggestions: Don’t drop it, or expose it to shock. If the computer falls, the case and the components could be damaged. Keep it dry, and don’t overheat it.
Page 8: Power Safety
Preface Power Safety The computer has specific power requirements: • When you want to unplug the power cord, be sure to disconnect it by the plug head, not by its wire. • Make sure the socket and any extension cord(s) you use can support the total current load Power Safety of all the connected devices.
Page 9: Cleaning
Preface Cleaning Do not apply cleaner directly to the computer, use a soft clean cloth. Do not use volatile (petroleum distillates) or abrasive cleaners on any part of the computer. Servicing Do not attempt to service the computer yourself. Doing so may violate your warranty and expose you and the computer to electric shock.
Page 10: Ergonomics
Preface Ergonomics We designed your Multimedia PC system to be functional as well as attractive. To get most out of it, here are some suggestions on how to position and use the computer: • The top third of the LCD (screen) should be at eye-level or slightly below. •...
Page 11 Preface Lighting Proper lighting and comfortable display viewing angle can reduce eye strain and muscle fatigue in your neck and shoulders. • Position the display to avoid glare or reflections from overhead lighting or outside sources of light. • Keep the display screen clean and set the brightness and contrast to levels that allow you to see the screen clearly. •...
Page 12 Preface...
Page 13: Table Of Contents
Preface Contents Notice .................I System Map: Rear View ..........1-12 FCC Statement .............II Windows Vista Start Menu & Control Panel ....1-13 FCC RF Radiation Exposure Statement: ....III Video Features .............1-14 Instructions for Care and Operation ......V Display Devices & Options .........1-14 Power Safety ..............
Page 14 Preface Power Management LAN ................4-5 ExpressCard/Card Reader ..........4-6 Overview ................3-1 Hot Key ................4-6 Turning on the Computer ..........3-2 e-SATA Support ............4-6 Power Plans ..............3-3 Optional Drivers ............4-7 System Power Options ...........3-5 Bluetooth Module ............4-7 Hibernate vs. Shut Down ..........3-5 Wireless LAN Module ...........4-7 Sleep vs.
Page 15 Preface Revision (Main Menu) ...........5-7 Upgrading the Hard Disk Drive ........6-6 Advanced Menu .............5-8 Upgrading the System Memory (RAM) ......6-8 SIO ITE8305E (Advanced Menu) .........5-8 Upgrading the Processor ..........6-10 Installed O/S (Advanced Menu) ........5-9 Modules & Options SATA Mode Selection (Advanced Menu) ....5-9 DFOROM (Robson) Support (Advanced Menu >...
Page 16 Preface Troubleshooting USB 2.0/1.1 Ports ............A-5 Overview ................8-1 Intel Video Driver Controls Basic Hints and Tips ............8-2 Video ................B-1 Backup and General Maintenance .........8-3 Dynamic Video Memory Technology ......B-1 Viruses ................8-4 Scheme Options ............B-4 Upgrading and Adding New Hardware/Software ..8-5 Configuring Other Displays from Intel®...
Page 17 Preface ExpressCard Slot ............C-4 Driver Installation ............D-21 Mini-Card Slots ............C-4 Updating/Reinstalling Individual Drivers....D-22 Communication ............. C-4 Driver Installation Procedure........D-23 Power Management ............C-4 Chipset ................D-23 Power ................C-4 Video ................D-23 Environmental Spec ............C-4 Audio ................D-23 Dimensions &...
Page 18 Preface Calibrating the Touch Screen ........D-42...
Page 19: Quick Start Guide
Quick Start Guide Chapter 1: Quick Start Guide Overview This Quick Start Guide is a brief introduction to the basic features of your computer, to navigating around the computer and to getting your system started. The remainder of the manual covers the following: •...
Page 20: Advanced Users
Quick Start Guide Advanced Users If you are an advanced user you may skip over most of this Quick Start Guide. However you may find it useful to refer to “What to Install” on page 4 - “BIOS Utilities” on page 5 - 1 “Upgrading The Computer”...
Page 21: Not Included
Quick Start Guide Not Included Operating Systems (e.g. Windows Vista/Windows XP) and applications (e.g. word processing, spreadsheet and database programs) have their own manuals, so please consult the appropriate manuals. Drivers If you are installing new system software, or are re-configuring your computer for a different system, you will need to install the drivers listed in “Drivers &...
Page 22: System Software
Quick Start Guide System Software Your computer may already come with system software pre-installed. Where this is not the case, or where you are re-configuring your computer for a different system, you will find the following operating systems are sup- ported.
Page 23: System Startup
Quick Start Guide System Startup Remove all packing materials, CDs/DVDs and floppy disks etc. Securely attach any peripherals you want to use with the computer to their ports (e.g keyboard and mouse etc.) Attach the AC/DC adapter to the DC-In jack located under the LCD, then plug the AC power cord into an outlet, and connect the AC power cord to the AC/DC adapter.
Page 24: System Map: Front View
Quick Start Guide System Map: Front View Optional Built-In PC Camera LCD (With Optional Touch Panel) Power & System Activity LED Indicators Volume Buttons (under the LCD) Brightness Buttons (under the LCD) Power Button (under the LCD) USB Ports Microphone-In Jack Headphone/Speaker-Out Jack 10.
Page 25: Tilting The Lcd Screen
Quick Start Guide Tilting the LCD Screen It is possible to tilt the LCD screen in order to get the best possible viewing angle of the screen without glare etc. Apply pressure with one hand at the base of the computer, while carefully pushing the LCD screen to tilt it to the appropriate viewing angle.
Page 26: Keyboard Options
Quick Start Guide Keyboard Options There are two keyboard options for this computer series. These keyboards may include embedded numerical keypads for easy numeric data input and/or function keys/hot keys to allow you to change operational features instantly. Some keyboards may require a driver to access all available functions etc. Figure 1 - 4 - Optional Wireless Keyboard &...
Page 27: Led & Hot Key Indicators
Quick Start Guide LED & Hot Key Indicators Visual indicators for brightness and volume are avail- able when the hot key utility is installed (see “Hot The LED indicators on the computer display helpful Key” on page 4 - 6). When the driver is installed, an information about the current status of the computer.
Page 28: System Map: Left View
Quick Start Guide System Map: Left View Figure 1 - 5 Left View Stand S/PDIF-Out Jack ExpressCard Slot Headphone-Out Jack The ExpressCard Slot accepts either Microphone-In Jack ExpressCard/34 or ExpressCard/ 54 formats. Line-In Jack Mini-IEEE 1394 7-in-1 Card Reader Port HDMI-Out Port The card reader allows you to use 1 * USB 2.0 Port...
Page 29: System Map: Right View
Quick Start Guide System Map: Right View Figure 1 - 6 - Right View Stand CD Emergency Eject Optical Device Drive Bay (for CD/DVD Device - see page If you need to manually eject a CD/DVD (e.g. due to an unexpected power interruption) push the end of a straight- Changing DVD Regional Codes...
Page 30: System Map: Rear View
Quick Start Guide System Map: Rear View Figure 1 - 7 Rear View Stand Rear Component Cover The CPU is not a user serviceable Vent/Fan Intake part. Opening this compartment, or Security Lock Slot accessing the CPU in any way, Carrying Handle may violate your warranty.
Page 31: Windows Vista Start Menu & Control Panel
Quick Start Guide Windows Vista Start Menu & Control Panel Most of the control panels, utilities and programs within Windows Vista (and most other Windows versions) are accessed from the Start menu. When you install programs and utilities they will be installed on your hard disk drive, and a shortcut will usually be placed in the Start menu and/or the desktop.
Page 32: Video Features
Quick Start Guide Video Features You can switch display devices, and configure display options, from the Display Settings control panel (in Per- sonalization) in Windows Vista as long as the appropriate Intel video driver is installed. For more detailed vid- eo information see “Intel Video Driver Controls”...
Page 33 Quick Start Guide Figure 1 - 9 - Display Properties Desktop Intel Display Mode Description Single Mode One of the connected displays is used as the display device Intel(R) Dual Display Clone Mode Both connected displays output the same view and may be configured independently Extended Desktop Mode Both connected displays are treated as separate devices, and act as a virtual desktop Table 1 - 4 - Display Options...
Page 34: Power Options
Quick Start Guide Power Options The Power Options (Hardware and Sound menu) control panel icon in Windows (see page 13) allows you to configure power management features for your computer. You can conserve power by means of power plans and configure the options for the power button, sleep button, display and sleep mode from the left menu. Note that the power saver plan may have an affect on computer performance.
Page 35: Features & Components
Features & Components Chapter 2: Features & Components Overview Read this chapter to learn more about the following main features and components of the computer: • Hard Disk Drive • Optical (CD/DVD) Device • 7-in-1 Card Reader • ExpressCard Slot •...
Page 36: Hard Disk Drive
Features & Components Hard Disk Drive The hard disk drive is used to store your data in the computer. The hard disk can be Power Safety taken out to accommodate other 2.5" serial (SATA) hard disk drives with a height of 9.5 mm.
Page 37: Optical (Cd/Dvd) Device
Features & Components Optical (CD/DVD) Device There is a bay for a 5.25" optical (CD/DVD) device (12.7mm height). The actual de- Sound Volume vice will depend on the module you purchased (see “Storage” on page C - 3). The Adjustment optical device is usually labeled “Drive D:”...
Page 38: Handling Cds Or Dvds
Features & Components Handling CDs or DVDs Proper handling of your CDs/DVDs will prevent them from being damaged. Please follow the advice below to make sure that the data stored on your CDs/DVDs can be CD Emergency Eject accessed. If you need to manually eject a CD (e.g.
Page 39: Dvd Regional Codes
Features & Components DVD Regional Codes To change the DVD regional codes see “Changing DVD Regional Codes” on page 1 - DVD Regional Coding Region Geographical Location USA, Canada Table 2 - 1 Western Europe, Japan, South DVD Regional Africa, Middle East & Egypt Coding South-East Asia, Taiwan, South Korea, The Philippines, Indonesia,...
Page 40: 7-In-1 Card Reader
Features & Components 7-in-1 Card Reader The card reader allows you to use some of the latest digital storage cards. Push the Card Reader Cover card into the slot and it will appear as a removable device, and can be accessed in the same way as your hard disk (s).
Page 41: Expresscard Slot
Features & Components ExpressCard Slot The computer is equipped with an ExpressCard/34/54 slot that reads Express Card/ ExpressCard Slot 34 and ExpressCard/54 formats. ExpressCards are the successors to PCMCIA (PC Cover Cards). Make sure you keep the ExpressCard/54 is used for applications which cover in the Express- require a larger interface slot, e.g.
Page 42: Audio Features
Features & Components Audio Features You can configure the audio options on your computer from the Sound control Sound Volume panel in Windows, or from the Realtek HD Audio Manager icon in the taskbar/ Adjustment control panel (right-click the taskbar icon to bring up an audio menu).
Page 43: Audio Jacks
Features & Components Audio Jacks Note that the system has two sets of audio jacks as well as internal speakers. All the audio jacks cannot function at the same time and are therefore assigned a priority order depending on your audio connections. •...
Page 44: Adding A Printer
Features & Components Adding a Printer The most commonly used peripheral is a printer. The following conventions will Parallel Printer help you to add a printer, however it is always best to refer to the printer manual for specific instructions and configuration options. After setting up the print- er attach the parallel ca- ble to the printer.
Page 45: Power Management
Power Management Chapter 3: Power Management Overview OS Note Power management To conserve power, especially when using the battery, your computer power man- functions will vary slight- agement conserves power by controlling individual components of the computer ly depending on your (the monitor and hard disk drive) or the whole system.
Page 46: Turning On The Computer
Power Management Turning on the Computer To turn the computer on simply press the power button (see “System Startup” on Shut Down page 1 - Note that you should al- When the computer is on, you can use the power button as a Sleep/Hibernate hot- ways shut your comput- er down by choosing the key button when it is pressed for less than 4 seconds (pressing and holding the power...
Page 47: Power Plans
Power Management Power Plans The computer can be configured to conserve power by means of power plans. You Resuming can use (or modify) an existing power plan, or create a new one. Operation The settings may be adjusted to set the display to turn off after a specified time, and Table 3 - 1, on to send the computer into Sleep after a period of inactivity.
Page 48 Power Management Each Windows power plan will also adjust the processor performance of your ma- chine in order to save power. This is worth bearing in mind if you are experiencing any reduced performance. Figure 3 - 2 Power Plans 3 - 4 Power Plans...
Page 49: System Power Options
Power Management System Power Options You can use the system power options to stop the computer’s operation and restart Sleep Button where you left off. The system features Sleep and Hibernate power saving states. The Power Button Hibernate vs. Shut Down in the Start Menu (in Classic View use the Hibernate and Shut Down are the same in that the system is off and you need to press...
Page 50: Sleep
Power Management Sleep Sleep uses very little system power, and takes a short time to return to full operation. After an extended period of time in Sleep the computer will save the contents of sys- Hibernate Mode In tem memory (e.g. any open documents and applications) to the hard disk and shut Windows Vista SP1 the system down.
Page 51: Configuring The Power Button
Power Management Configuring the Power Button The power button may be set to send the computer in to either Sleep or Hibernate. Password In Sleep, the LED will blink green. In Hibernate the LED will be orange. If only Protection the display is turned off, the LED will remain green.
Page 52: Resuming Operation
Power Management Resuming Operation You can resume operation from power-saving states by pressing the power button, or in some cases pressing the sleep button (see your keyboard documentation). Power Status To Resume Icon Color Power Off Press the Power Button Press the Power Button Sleep Blinking Green...
Page 53: Drivers & Utilities
Drivers & Utilities Chapter 4: Drivers & Utilities What to Install This chapter deals with installing the drivers and utili- ties essential to the operation or improvement of some The Device Drivers & Utilities + User’s Manual disc of the computer’s subsystems. The system takes ad- contains the drivers and utilities necessary for the vantage of some newer hardware components for proper operation of the computer.
Page 54: Driver Installation
Drivers & Utilities Driver Installation Check the driver installation order from Table 4 - 1, on page 4 - 3 (the drivers must be installed in Insert the Device Drivers & Utilities + User’s Manual this order) which is the same as that listed in the disc and click Install Drivers (button)/Option Drivers Drivers Installer menu below.
Page 55 Drivers & Utilities Manual Driver Installation Driver - Windows Vista with Service Pack 1 Page # Click Browse CD (button) in the Drivers Installer ap- plication and browse to the executable file in the ap- Chipset Page 4 - 5 propriate driver folder.
Page 56: Updating/Reinstalling Individual Drivers
Drivers & Utilities Updating/Reinstalling Individual Drivers User Account Control (Win Vista) If you wish to update/reinstall individual drivers it If a User Account Control prompt appears as part of may be necessary to uninstall the original driver.To do the driver installation procedure, click Continue or this go to the Control Panel in the Windows OS and Allow, and follow the installation procedure as direct- double-click the Programs and Features icon (Pro-...
Page 57: Driver Installation Procedure
Drivers & Utilities Driver Installation Procedure Modem Insert the Device Drivers & Utilities + User’s Manual 1. Click 4.Install Modem Driver > Yes. disc and click Install Drivers (button), or Option Driv- 2. Click OK. ers (button) to access the Optional driver menu. 3.
Page 58: Expresscard/Card Reader
Drivers & Utilities ExpressCard/Card Reader 1. Click 6.Install CardReader Driver > Yes. 2. Click Next > Install. Windows Update 3. Click Finish to complete the installation. After installing all the drivers make sure you enable Win- dows Update in order to get all the latest security up- Hot Key dates etc.
Page 59: Optional Drivers
Drivers & Utilities Optional Drivers Bluetooth Module See the pages indicated for the driver installation pro- Note: The operating system is the default setting for cedures for any modules included in your purchase op- Bluetooth control in Windows Vista. See “Bluetooth tion.
Page 60 Drivers & Utilities 4 - 8...
Page 61: Bios Utilities
BIOS Utilities Chapter 5: BIOS Utilities Overview BIOS Settings Warning This chapter gives a brief introduction to the computer’s built-in software: Incorrect settings can cause your system to Diagnostics: The POST (Power-On Self Test) malfunction. To correct mistakes, return to Set- up and restore the Set- Configuration: The Setup utility up Defaults with <F9>.
Page 62: The Power-On Self Test (Post)
BIOS Utilities The Power-On Self Test (POST) Each time you turn on the computer, the system takes a few seconds to conduct a POST, including a quick test of the on-board RAM (memory). As the POST proceeds, the computer will tell you if there is anything wrong. If there is a problem that prevents the system from booting, it will display a system summary and prompt you to run Setup.
Page 63: Failing The Post
BIOS Utilities Failing the POST Errors can be detected during the POST. There are two categories, “fatal” and “non- fatal”. Fatal Errors These stop the boot process and usually indicate there is something seriously wrong with your system. Take the computer to your service representative or authorized service center as soon as possible.
Page 64: The Setup Program
BIOS Utilities The Setup Program The Setup Utility program tells the system how to configure itself and manage basic features and subsystems (e.g. port configuration). Entering Setup To enter the Setup Utility, turn on the computer and press F2 during the POST. The prompt (Press F2 to Enter Setup) seen on page 5 - 2 is usually present for a few sec-...
Page 65: Setup Screens
BIOS Utilities Setup Screens The following pages contain additional advice on portions of the Setup Utility. Setup Menus Along the top of the screen is a menu bar with menu headings. When you select a Setup menus heading, a new screen appears. Scroll through the features listed on each screen to shown in this section are make changes to Setup Utility.
Page 66: Main Menu
BIOS Utilities Main Menu Phoenix SecureCore(tm) Setup Utility Figure 5 - 1 Main Main Advanced Security Boot Exit Main Menu Item Specific Help System Time: [22:12:05] System Date: [05/28/2008] <Tab>, <Shift Tab>, or SATA Port 1 [None] <Enter> selects field. SATA Port 2 [None] System Memory:...
Page 67: Sata Port 1/2 (Main Menu)
BIOS Utilities SATA Port 1/2 (Main Menu) Pressing Enter opens the sub-menu to show the configuration of a hard disk or op- tical device drive on the computer’s SATA Ports. Use the Auto (Type:) setting to have the items configured automatically for you. System/Extended Memory (Main Menu) This item contains information on the system memory, and is not user configurable.
Page 68: Advanced Menu
BIOS Utilities Advanced Menu Phoenix SecureCore(tm) Setup Utility Figure 5 - 2 Main Advanced Advanced Security Boot Exit Advanced Menu Item Specific Help SIO ITE8305E These items control Installed O/S: [Vista] SATA Mode Selection: [AHCI] the configuration of various National 393 DFOROM(Robson) Support: [Enabled] SIO devices.
Page 69: Installed O/S (Advanced Menu)
BIOS Utilities Installed O/S (Advanced Menu) This setting tells the computer what kind of operating system you’re using. Make sure you choose the correct setting for your O/S in order to prevent system problems. SATA Mode Note: If you select the Vista O/S then the SATA Mode Selection menu will become Selection available.
Page 70: Dforom (Robson) Support
BIOS Utilities DFOROM (Robson) Support (Advanced Menu > SATA Mode Selection [AHCI] This item will only be available if you have selected AHCI in SATA Mode Selec- tion. The option should be enabled if you have included an optional Intel Turbo SATA Mode &...
Page 71: Power On Boot Beep (Advanced Menu)
BIOS Utilities Power On Boot Beep (Advanced Menu) Use this menu to enable/disable the single beep sound at the end of the POST. This item is “Disabled” by default. Fan Control (Advanced Menu) This menu item allows you to set the fan cooling behavior under light system activity (if you choose Automatic the system will adjust the fan cooling as appropriate for the system activity).
Page 72: Security Menu
BIOS Utilities Security Menu Phoenix SecureCore(tm) Setup Utility Security Menu Main Advanced Security S S e e c c u u r r i i t t y y Boot Exit Item Specific Help changes Supervisor Password Is: Clear make here affect the User Password Is: Clear Supervisor Password...
Page 73: Set User Password (Security Menu)
BIOS Utilities Set User Password (Security Menu) You can set a password for user mode access to the Setup Utility. This will not af- fect access to the computer OS, (only the Setup utility) unless you choose to set a Password Warning Password on Boot (see below).
Page 74: Boot Menu
BIOS Utilities Boot Menu Phoenix SecureCore(tm) Setup Utility Figure 5 - 4 Main Advanced Security Boot Exit Boot Menu Item Specific Help Boot priority order: USB KEY: Keys used to view or USB HDD: configure devices: IDE CD: Up and Down arrows IDE HDD: select a device.
Page 75: Exit Menu
BIOS Utilities Exit Menu Figure 5 - 5 Phoenix SecureCore(tm) Setup Utility Main Advanced Security Boot Exit Exit Menu Item Specific Help Exit Saving Changes Exit Discarding Changes Exit System Setup and Load Setup Defaults save your changes to CMOS. Discard Changes Save Changes Help...
Page 76 BIOS Utilities 5 - 16...
Page 77: Upgrading The Computer
Upgrading The Computer Chapter 6: Upgrading The Computer Overview This chapter contains information on upgrading the computer. Follow the steps out- lined to make the desired upgrades. If you have any trouble or problems you can con- Warranty Warning tact your service representative for further help. Before you begin you will need: Please check with your service representative...
Page 78: When Not To Upgrade
Upgrading The Computer When Not to Upgrade These procedures involve opening the system’s case, adding and sometimes replac- ing parts. Power Safety Warning You should not perform any of these upgrades if: Before you undertake upgrade proce- • Your system is still under warranty or a service contract dures, make sure that •...
Page 79: Removing The Rear Top Cover
Upgrading The Computer Removing the Rear Top Cover Before undertaking any upgrade procedure it is necessary to remove the rear top cover to access the components. Turn off the computer and disconnect all cables and peripherals. Carefully place the computer flat with the LCD facing down (make sure you cover the LCD to avoid scratches) so that you may access the rear cover.
Page 80 Upgrading The Computer Slide the rear top cover until the arrow is aligned with the unlock icon Figure 6 - 2 Rear Top Cover Unlock When the arrow is aligned with the unlock icon you can remove the rear top cover Figure 6 - 3 Rear Top Cover...
Page 81: Wireless Keyboard & Mouse Usb Receiver
Upgrading The Computer Wireless Keyboard & Mouse USB Receiver If your purchase includes an optional Wireless Keyboard & Mouse Kit you can use the USB port located behind the rear top cover to house the USB receiver. Remove the rear cover (see “Removing the Rear Top Cover”...
Page 82: Upgrading The Hard Disk Drive
Upgrading The Computer Upgrading the Hard Disk Drive The hard disk drive can be taken out to accommodate other 2.5" serial (SATA) hard HDD System disk drives with a height of 9.5mm (h) (see “Storage” on page C - 3). Follow your Warning operating system’s installation instructions, and install all necessary drivers and util- ities (as outlined in...
Page 83 Upgrading The Computer Firstly slide the hard disk in the direction of arrow , and then slide it in the direction of arrow to remove it. Figure 6 - 6 Hard Disk Assembly Removal Remove the adhesive hard disk cover Figure 6 - 7 Hard Disk Cover Removal...
Page 84: Upgrading The System Memory (Ram)
Upgrading The Computer Upgrading the System Memory (RAM) The computer has two memory sockets for 200 pin Small Outline Dual In-line (SO- DIMM) DDRII (DDR2) type memory modules (see “Memory” on page C - 2 details of supported module types). The total memory size is automatically detected by the POST routine once you turn on your computer.
Page 85 Upgrading The Computer Gently pull the two release latches on the sides of the memory socket in the direction indicated by the arrows ( & Figure 6 - Contact Warning Be careful not to touch the metal pins on the module’s connecting edge.
Page 86: Upgrading The Processor
Upgrading The Computer Upgrading the Processor If you want to upgrade your computer by replacing the existing processor with a fast- Warranty er/new one you will need to contact your customer service representative. We rec- ommend that you do not do this yourself, since if it is done incorrectly you may The CPU is not a user damage the processor or mainboard.
Page 87: Modules & Options
Modules & Options Chapter 7: Modules & Options Overview This chapter contains information on the following modules, which may come with your computer, depending on the configuration purchased. If you are unsure please contact your service representative. • Bluetooth Module •...
Page 88: Bluetooth Module
Modules & Options Bluetooth Module The optional Bluetooth module allows you to connect your computer to Bluetooth enabled devices such as other computers, desktop computers, mobile phones, print- ers, digital cameras, PDAs, headsets etc. using a short-range radio frequency. The operating system’s Bluetooth Devices control panel is used to configure the Bluetooth settings in Windows Vista, and therefore does not require a driver.
Page 89: Bluetooth Configuration In Windows Vista
Modules & Options Bluetooth Configuration in Windows Vista Setup your Bluetooth Device so the Computer Can Find it Turn your Bluetooth device (e.g. PDA, mobile phone etc.) on. Bluetooth Taskbar Make the device discoverable (to do this check your device documentation). Icon If you cannot see the To Turn the Bluetooth Module On...
Page 90 Modules & Options To Add a Bluetooth Device Access the Bluetooth Devices control panel. Click Options (tab), and make sure that Allow Bluetooth devices to connect to this computer check box (Connections) has a tick inside it. Click Devices (tab), and then click Add. The Add Bluetooth Device Wizard will appear.
Page 91 Modules & Options To Change Settings for the Bluetooth Device Access the Bluetooth Devices control panel. Click on the device you want to change and click Properties to: Bluetooth Help • Change the name of the device (click General, type a new name and click OK). •...
Page 92: 7 - 6 Wireless Lan Module
Modules & Options Wireless LAN Module If you have included an Intel® Wi-Fi Link 5100/5300 Series (802.11 a/g/n) WLAN module, or 3rd Party 802.11b/g WLAN module in your purchase option, install the driver as per the procedure overleaf. Make sure you install the drivers in the order indicated in Table 4 - 1, on page 4 - 7 - 6 Wireless LAN Module...
Page 93: Intel® Wi-Fi Link 5100/5300 Series (802.11 A/G/N) Driver Installation
Modules & Options Intel® Wi-Fi Link 5100/5300 Series (802.11 a/g/n) Driver Installation 1. Insert the Device Drivers & Utilities + User’s Manual disc into the CD/ DVD drive. 2. Click Option Drivers (button). 3. Click 1.Install WLAN Driver > Yes. 4.
Page 94: Connecting To A Wireless Network
Modules & Options Connecting to a Wireless Network Make sure the Wireless LAN module is turned on (see page 11). Click the taskbar wireless icon , and then click Connect to a network (or right- click the icon , and then click Connect to a network). Figure 7 - 5 Taskbar Menus Click icon...
Page 95 Modules & Options Click a network, and then click Connect. If you do not see a network you want to connect to, click Set up a connection or network (a list of options will appear allowing manual searching, and creating a new network).
Page 96 Modules & Options To disconnect from the wireless network you can click the taskbar wireless icon and then select Connect or disconnect to access the network menu, and click Disconnect (or right-click the icon , and then click Disconnect from). Security Enabled Networks You should try to make...
Page 97: Windows Mobility Center
Modules & Options Windows Mobility Center The Windows Mobility Center control panel provides an easy point of access for information on battery status, power plans used and wireless device status etc. To access the Windows Mobility Center: Click Start, and click Control Panel (or point to Settings and click Control Panel).
Page 98: Pc Camera Module
Modules & Options PC Camera Module There PC Camera module uses the BisonCap application to capture video files. In- 2.0M PC Camera stall the driver as per the instructions below. Screen Refresh The 2.0M PC Camera module supports Latest PC Camera Driver Information frame rate of 12 fps.
Page 99: Pc Camera Audio Setup
Modules & Options PC Camera Audio Setup If you wish to capture video & audio with your camera, it is necessary to connect a microphone to either of the microphone ports and then setup the audio recording op- tions in Windows as follows. Click Start, and click Control Panel (or point to Settings and click Control Panel).
Page 100 Modules & Options Figure 7 - 11 Audio Setup for PC Camera Right-click 7 - 14 PC Camera Module...
Page 101 Modules & Options BisonCap BisonCap is a video viewer for general purpose video viewing and testing, and cap- turing video files to .avi format. Pre-Allocating File Space Run the BisonCap program from the Start > Programs/All Programs > Bison- Cam menu (it is recommended that you set the capture file before the capture You may pre-allocate process - see Set Capture File below).
Page 102 Modules & Options Reducing Video File Size Note that capturing high resolution video files requires a substantial amount of disk space for each file. After recording video, check the video file size (right-click the file and select Properties) and the remaining free space on your hard disk (go to My Computer, right-click the hard disk, and select Properties).
Page 103 Modules & Options Eliminating Screen Flicker If you find that the video screen in the BisonCap program is flickering, you can try to adjust the setting in the Video Capture Filter options. Run the BisonCap program. Go to Options and scroll down to select Video Capture Filter..Click either 50Hz or 60Hz under Frequency in Property Page (tab).
Page 104 Modules & Options Zoom The BisonCap program allows you to zoom the camera in and out. Run the BisonCap program. Go to Zoom and select Zoom Out/Zoom In. Figure 7 - 13 Zoom/Setting Taking Still Pictures Snapshot Folder The BisonCap programs allows you to take still pictures. The Snapshot folder’s default location is on the Run the BisonCap program.
Page 105: Touch Screen Module
Modules & Options Touch Screen Module If you have included a Touch Screen module in your purchase option, you should ob- Touch Screen Input tain a stylus pen to interact with the computer in the same way you would use a Device mouse (use a stylus pen to tap/double-tap on-screen buttons etc.).
Page 106: Calibrating The Touch Screen
Modules & Options Calibrating the Touch Screen Click Start, and click Programs/All Programs and point to Touch Utilities (folder), and then click Touch Configuration program (or double-click the desk- top icon Click Calibration (button). Figure 7 - 14 Touch Screen Configuration 7 - 20 Touch Screen Module...
Page 107 Modules & Options Click to choose the number of points in Calibration Precision, and then click Calibrate (button). Figure 7 - 15 Calibration Precision Use the stylus pen to touch the center of the cross sign until the OK sign appears in the center of the cross.
Page 108 Modules & Options When the Test Drawing appears, write on the screen to test the calibration (press the spacebar to clear any drawing, or Esc to exit). Figure 7 - 17 Test Drawing Click Close to exit Calibration. Click Touch Settings (button) to adjust any touch setting (mouse) options. Figure 7 - 18 Touch Settings 7 - 22 Touch Screen Module...
Page 109: Tablet Pc Input Panel
Modules & Options Tablet PC Input Panel When not in use the Tablet PC Input Panel (not available in Windows Vista Home Basic Edition) docks at the side of the screen (and may be docked at either side of Tablet PC Settings the screen at any height) with just a small portion visible.
Page 110: Intel Turbo Memory Module
Modules & Options Intel Turbo Memory Module If you have included an Intel Turbo Memory (Robson) NAND flash memory card e-SATA Port module in your purchase option, then you will need to install the driver as per the Support instructions below (do not install this driver in Windows XP). Note that the Intel Ma- Intel Turbo Memory Technology (also known as Robson flash memory) is an Intel trix Storage driver is...
Page 111 Modules & Options 6. Insert the Device Drivers & Utilities + User’s Manual disc into the CD/ DVD drive. 7. Click Option Drivers (button). Windows Security 8. Click 4.Install TM&iMSM Driver > Yes. Message 9. Click Next > Yes > Next > Next. 10.
Page 112 Modules & Options 1. Run the Intel ® Turbo Memory Console from the Programs/All Pro- grams menu (Intel ® Turbo Memory). Figure 7 - 21 Intel Turbo Memory Console • Windows ReadyBoost - uses flash memory as a hard-drive caching solution. •...
Page 113: Troubleshooting
Troubleshooting Chapter 8: Troubleshooting Overview Should you have any problems with your computer, before consulting your service representative, you may want to try to solve the problem yourself. This chapter lists some common problems and their possible solutions. This can’t anticipate every problem, but you should check here before you panic. If you don’t find the answer in these pages, make sure you have followed the instructions carefully and observed the safety precautions in the preface.
Page 114: Basic Hints And Tips
Troubleshooting Basic Hints and Tips Many of the following may seem obvious but they are often the solution to a problem when your computer ap- pears not to be working. • Power - Is the computer actually plugged into a working electrical outlet? If plugged into a power strip, make sure it is actually working.
Page 115: Backup And General Maintenance
Troubleshooting Backup and General Maintenance • Always backup your important data, and keep copies of your OS and programs safe, but close to hand. Don’t forget to note the serial numbers if you are storing them out of their original cases, e.g. in a CD wal- let.
Page 116: Viruses
Troubleshooting Viruses • Install an Anti-Virus program and keep the definitions file (the file which tells your program which viruses to look for) up to date. New computer viruses are discovered daily, and some of them may seriously harm your computer and cause you to lose data. Anti-Virus programs are commercially available and the defini- tions file updates are usually downloadable directly from the internet.
Page 117: Upgrading And Adding New Hardware/Software
Troubleshooting Upgrading and Adding New Hardware/Software • Do not be tempted to make changes to your Windows Registry unless you are very sure of what you are doing, otherwise you will risk severely damaging your system. • Don’t open your computer or undertake any repair or upgrade work if you are not comfortable with what you are doing.
Page 118 Troubleshooting • Thoroughly check any recent changes you made to your system as these changes may affect one or more system components, or software programs. If possible, go back and undo the change you just made and see if the problem still occurs. •...
Page 119: Problems & Possible Solutions
Troubleshooting Problems & Possible Solutions Problem Possible Cause - Solution The computer feels too Make sure the computer is properly ventilated and the Vent/Fan intakes are not blocked. If this hot. doesn’t cool it down, put the system into Hibernate mode or turn it off for an hour. Make sure the computer isn’t sitting on a thermal surface (see “Overheating”...
Page 120: Dvd Regional Codes
Troubleshooting Problem Possible Cause - Solution The compact disc tray The compact disc is not correctly placed in the tray. Gently try to remove the disc using the eject will not open when there hole (see “Loading Discs” on page 2 - is a disc in the tray.
Page 121 Troubleshooting Problem Possible Cause - Solution The system “hangs” (a You have disabled AHCI mode in the BIOS. If you have installed the Windows Vista operating blank screen appears system with AHCI mode enabled (default setting), DO NOT disable AHCI mode (if you wish to and the OS will not load) disable AHCI mode you will need to reinstall the Windows VIsta OS).
Page 122 Troubleshooting Problem Possible Cause - Solution No sound can be heard You have plugged in headphones or speakers to the audio jacks at the front of the computer. from the internal/external Note that the system has two sets of audio jacks as well as internal speakers. All the audio jacks speakers/headphones.
Page 123: Interface (Ports & Jacks)
Interface (Ports & Jacks) Appendix A: Interface (Ports & Jacks) Overview The following chapter will give a quick description of the interface (ports & jacks) which allow your computer to communicate with external devices, connect to the internet etc. Interface (Ports & Jacks) A - 1...
Page 124: Computer Ports And Jacks
Interface (Ports & Jacks) Computer Ports and Jacks Item Description Card Reader Port The card reader allows you to use some of the latest digital storage cards. Push the card into the slot and it will appear as a removable device. COM/Serial Ports The COM/serial is a communication interface for data transfer, through which information transfers in or out one bit at a time.
Page 125: External Monitor (Vga) Port
Interface (Ports & Jacks) Item Description External Monitor (VGA) This port allows you to connect an external monitor, or Flat Panel Display, to get dual video or Port simultaneous display on the LCD and external monitor/FPD (see “Configuring Other Displays from Intel®...
Page 126: Mini-Ieee 1394 Port
Interface (Ports & Jacks) Item Description Mini-IEEE 1394 Port This allows high-speed connection to various peripheral devices, e.g. external disk drives and digital cameras (see note below). IEEE 1394 The Mini-IEEE 1394 ports only support SELF POWERED IEEE 1394 devices. RJ-11 Phone Jack This port connects to the built-in modem.
Page 127: Usb 2.0/1.1 Ports
Interface (Ports & Jacks) Item Description USB 2.0/1.1 Ports These USB 2.0 compatible ports (USB 2.0 is fully USB 1.1 compliant) are for low-speed peripherals such as keyboards, mice or scanners, and for high-speed peripherals such as external HDDs, digital video cameras or high-speed scanners etc. Devices can be plugged into the computer, and unplugged from the computer, without the need to turn the system off (if the power rating of your USB device is 500mA or above, make sure you use the power supply which comes with the device).
Page 128 Interface (Ports & Jacks) A - 6...
Page 129: Intel Video Driver Controls
Intel Video Driver Controls Appendix B: Intel Video Driver Controls The basic settings for configuring the LCD are outlined in “Video Features” on page 1 - DVMT Notes Intel Video Driver Installation DVMT is not local video Make sure you install all the drivers in the order indicated in Table 4 - 1, on page 4 - memory.
Page 130: Intel Graphics Properties
Intel Video Driver Controls Intel Graphics Properties More advanced video configuration options are provided by the Intel(R) Graphics Taskbar Icon Media Accelerator Driver for mobile control panel. The Intel GMA control Open the Display Settings control panel (see “Video Features” on page 1 - panel can also be ac- and click Advanced Settings (button).
Page 131 Intel Video Driver Controls You may make changes to the devices, color, schemes, Hot Keys etc. by clicking the appropriate menu item or button. Help Menus Right-click on many of the items in the tabs to bring up the “What’s This?”...
Page 132: Scheme Options
Intel Video Driver Controls Scheme Options Use Scheme Options to configure quick settings for applications which require spe- cific resolution and color settings in order to run properly e.g. games, multimedia Application.exe programs. To set the scheme options: You will need to locate Open the Display Settings control panel and click Advanced Settings (button).
Page 133 Intel Video Driver Controls Attaching Other Displays Besides the built-in LCD you can also use an external monitor/flat panel display/TV HDMI (TV through HDMI-Out port only), connected to the external monitor port or to the HDMI-Out port (High-Definition Multimedia Interface) as your display device. The Note that HDMI sup- following are the display options: ports video and audio...
Page 134: Configuring Other Displays From Intel® Gma Driver For Mobile
Intel Video Driver Controls ® Configuring Other Displays from Intel GMA Driver for Mobile Attach your external display to the external monitor port or HDMI-Out port, and turn it on. Display Selection Go to the Intel(R) GMA Driver for mobile control panel (see “Intel Graphics Properties”...
Page 135 Intel Video Driver Controls HDMI Audio Configuration As HDMI (High-Definition Multimedia Interface) carries both audio and video sig- nals you will need to configure the audio output as per the instructions below. Windows Audio Setup for HDMI Connect a device with HDMI support to the HDMI-Out port. Click Start, and click Control Panel (or point to Settings and click Control Panel).
Page 136 Intel Video Driver Controls HDMI Notes • Connect a device with HDMI support to the HDMI-Out port BEFORE attempt- ing to play audio/video sources through the device. Other Applications • If you disconnect the HDMI cable the default audio playback device will not If you are using a third party application...
Page 137: Display Modes
Intel Video Driver Controls Display Modes Single Display Video Settings Only one of your attached displays is used. Click Video Settings (button) in the Intel(R) Intel(R) Dual Display Clone (mirrored) GMA Driver for mobile This mode will drive multiple displays with the same content. Each device may be control panel to access configured independently for different resolutions, refresh rates, color quality etc.
Page 138: To Enable Intel(R) Dual Display Clone
Intel Video Driver Controls To Enable Intel(R) Dual Display Clone Attach your external display to the external monitor port or HDMI-Out port, and turn it on. Go to the Intel(R) GMA Driver for mobile control panel (see “Intel Graphics Properties” on page B - 2) and click Display Devices.
Page 139: To Enable Extended Desktop
Intel Video Driver Controls To Enable Extended Desktop Attach your external display to the external monitor port or HDMI-Out port, and turn it on. Display Settings Go to the Intel(R) GMA Driver for mobile control panel (see “Intel Graphics Extended Desktop Properties”...
Page 140 Intel Video Driver Controls Using Windows Vista to Enable Extended Mode Attach your external display to the external monitor port or HDMI-Out port, and turn it on. Display Settings If a New Display Detected window does not appear in Windows Vista, go to the Extended Desktop Windows Mobility Center control panel (Mobile PC >...
Page 141: Using Display Settings To Enable Extended Mode
Intel Video Driver Controls Using Display Settings to Enable Extended Mode Attach your external display to the external monitor port or HDMI-Out port, and turn it on. Open the Display Settings control panel (see “Video Features” on page 1 - 18).
Page 142 Intel Video Driver Controls B - 14...
Page 143: Specifications
Specifications Appendix C: Specifications Latest Specification Information The specifications listed in this Appendix are correct at the time of going to press. Certain items (particularly processor types/ speeds and CD/DVD device types) may be changed or updated due to the manufacturer's release schedule. Check with your service center for details.
Page 144: Processor
Specifications Feature Specification Processor Intel® Core™2 Duo Processor 45nm (45 Nanometer) Process Technology (478-pin) Micro-FC-PGA Package, Socket P 6MB On-die L2 Cache & 1066MHz FSB TDP: 35W 2.53/ 2.8 GHz T9400/ T9600 Intel® Core™2 Duo Processor 45nm (45 Nanometer) Process Technology (478-pin) Micro-FC-PGA Package, Socket P 6MB On-die L2 Cache &...
Page 145: Video Adapter
Specifications Feature Specification Video Adapter Intel GM45 Integrated Video Intel® Gen 5.0 Integrated Graphics Engine Integrated High Definition Multimedia Interface (HDMI) Supports DirectX10 3D Graphics Engine Accelerator BIOS One 32Mb Flash ROM Phoenix™ BIOS Storage One Changeable 12.7mm(h) Optical Device (CD/DVD) Type Drive (see “Optional”...
Page 146: Expresscard Slot
Specifications Feature Specification Card Reader Embedded 7-in-1 Card Reader (MS/ MS Pro/ SD/ Mini SD/ MMC/ RS MMC/ MS Duo) Note: MS Duo/ Mini SD/ RS MMC Cards Require a PC Adapter ExpressCard Slot ExpressCard/34/54 Slot Mini-Card Slots One Mini-Card Slot for Wireless LAN Module Communication Built-In 56K MDC Plug &...
Page 147 Specifications Feature Specification Dimensions & 450mm (w) * 312mm (d) * 66.5mm (h) 11kg Weight Optional Combo Drive Module 1.3M or 2.0M Pixel USB PC Camera Module DVD Dual (Super Multi) Drive Module (Factory Option) Wireless LAN Module: Bluetooth 2.0 + EDR (Enhanced Data Rate) Intel®...
Page 148 Specifications...
Page 149 Windows XP Information Appendix D: Windows XP Information This Appendix contains information (including control panel information, driver installation etc.) for users of the Windows XP OS. D - 1...
Page 150: Dvd Regional Codes
Windows XP Information DVD Regional Codes Changing DVD Regional Codes Go to the Control Panel and double-click System > Hardware (tab), click Device Manager, then click the + next to DVD/CD-ROM drives. Double-click on the DVD-ROM device to bring up the Properties dialogue box, and select the DVD Region (tab) to bring up the control panel to allow you to adjust the regional code.
Page 151: Windows Xp Start Menu & Control Panel
Windows XP Information Windows XP Start Menu & Control Panel Most of the control panels, utilities and programs within Windows XP (and most other Windows versions) are accessed from the Start menu. When you install programs and utilities they will be installed on your hard disk drive, and a shortcut will usually be placed in the Start menu and/or the desktop.
Page 152: Audio Features
Windows XP Information Audio Features You can configure the audio options on your computer from the Sounds and Audio Devices Windows con- trol panel, or from the Realtek HD Audio Manager icon in the taskbar/control panel (this will bring up the Realtek Audio Configuration menus).
Page 153: Audio Jacks
Windows XP Information Audio Jacks Note that the system has two sets of audio jacks as well as internal speakers. All the audio jacks cannot func- tion at the same time and are therefore assigned a priority order depending on your audio connections. •...
Page 154: Video Features
Windows XP Information Video Features You can switch display devices, and configure display options, from the Display Properties control panel in Windows as long as the appropriate video driver is installed. To access Display Properties in Windows: Click Start, point to Settings and click Control Panel (or just click Control Panel). Double-click Display (icon) - In the Appearances and Themes category.
Page 155: Display & Graphics Properties
Windows XP Information Display & Graphics Properties Taskbar Icon You can also access the controller prop- erties from the taskbar. Click on the icon to bring up the menu and scroll to Graphics Properties. If you cannot see the tray icon go to the Intel(R) Graphics Media Accelerator Driver for Mobile tab and click the “Show Tray Icon”...
Page 156 Windows XP Information You may make changes to the devices, color, schemes, Hot Keys etc. by clicking the appropriate menu item or button. Help Menus Right-click on many of the items in the tabs to bring up the “What’s This?” button. Click the “What’s This?”...
Page 157: Display Devices & Options
Windows XP Information Display Devices & Options Besides the built-in LCD, you can also use an external VGA monitor (CRT) or external Flat Panel Display as your display device. A VGA monitor/Flat Panel Display connects to the external monitor port. The following display modes are available.
Page 158: D - 10 Attaching Other Displays
Windows XP Information Attaching Other Displays If you prefer to use a monitor or flat panel display, connect it to the external monitor Display Selection port on the left of the computer. At least one other dis- 1. Attach your external display to the external monitor port, and turn it on. play must be attached in 2.
Page 159 Windows XP Information To Enable Intel(R) Dual Display Clone (Intel GMA) Attach your external display to the external monitor port, and turn it on. Go to the Intel(R) GMA Driver for mobile control panel and click Display Devices. Click to choose Intel(R) Dual Display Clone (Operating Mode). Click Apply, and OK to confirm the settings change.
Page 160 Windows XP Information To Enable Extended Desktop (Intel GMA) Attach your external display to the external monitor port, and turn it on. Go to the Intel(R) GMA Driver for mobile control panel and click Display Devices. Click to choose Extended Desktop (Operating Mode). Click Apply, and OK to confirm the settings change.
Page 161 Windows XP Information To Enable Extended Desktop (Windows Display Properties) Attach your external monitor to the external monitor port, and turn it on. Click Start, point to Settings (or click Control Panel) and click Control Panel (if you are in Category View choose Appearance and Themes).
Page 162: Hdmi Audio Configuration
Windows XP Information HDMI Audio Configuration As HDMI (High-Definition Multimedia Interface) carries both audio and video sig- nals you will need to configure the audio output as per the instructions below. Windows Audio Setup for HDMI 1. Connect a device with HDMI support to the HDMI-Out port. 2.
Page 163 Windows XP Information HDMI Notes • Connect a device with HDMI support to the HDMI-Out port BEFORE attempt- Other Applications ing to play audio/video sources through the device. If you are using a third • If you disconnect the HDMI cable the default audio playback device will not party application revert to speakers until the computer is restarted (if you do not wish to restart the...
Page 164: Power Management
Windows XP Information Power Management The computer uses the ACPI power management system to conserve power by con- Shutdown trolling individual components of the computer (the monitor and hard disk drive) or the whole system. Note that you should always shut your com- puter down by choos- Using some form of power management greatly increases the life span of the ing the Shut Down/...
Page 165: Power Schemes
Windows XP Information Power Schemes You can set your computer to conserve power through individual components by means of Power Schemes. You can also adjust the settings for each scheme to set Resuming the monitor to turn off after a specified time, and the computer's hard disk motor to Operation turn off if the hard disk drive has not been accessed for a specified period of time (if The system can re-...
Page 166: Configuring The Power Button
Windows XP Information System Power Options You can use the system power options to stop the computer’s operation and restart where you left off. This system features Standby and Hibernate sleep mode levels Power Button as Standby or (Hibernate mode will need to be enabled by clicking the option in the Hibernate tab Hibernate Button in the Power Options control panel - Figure D - 13 on page D -...
Page 167 Windows XP Information Standby Standby saves the least amount of power, but takes the shortest time to return to full operation. During Standby the hard disk is turned off, and the CPU is made to idle at System Resume its slowest speed. All open applications are retained in memory. When you are not The system can resume using your computer for a certain length of time, which you specify in the operating from Standby mode by:...
Page 168: Configuring The Power Button
Windows XP Information Configuring the Power Button The power button may be set to send the computer in to either Standby or Hibernate mode. In Standby mode, the Power LED will blink green. In Hibernate the LED will be orange. If the only the display is turned off, the LED will remain green. Figure D - 14 Power Options (Advanced - Power...
Page 169: Driver Installation
Windows XP Information Driver Installation Check the driver installation order from Table 5 (the drivers must be installed in this order) which is Insert the Device Drivers & Utilities + User’s Manual the same as that listed in the Drivers Installer CD-ROM, click Install Drivers/Option Drivers (but- menu below.
Page 170: Driver Installation
Windows XP Information Updating/Reinstalling Individual Drivers WinXP SP2 Driver Page # If you wish to update/reinstall individual drivers it may be necessary to uninstall the original driver.To do this go Chipset Page D - 23 to the Control Panel in the Windows OS and double- Video Page D - 23 click the Add/Remove Programs item.
Page 171: Chipset
Windows XP Information Driver Installation Procedure Insert the Device Drivers & Utilities + User’s Manual disc, click Install Drivers/Option Drivers (button) and Windows XP Service Pack 2 then click the appropriate driver name from the Drivers Make sure you install Windows XP Service Pack 2 (or a Installer menu.
Page 172: Cardreader
Windows XP Information Modem CardReader 1. Click 4.Install Modem Driver > Yes. 1. Click 6.Install CardReader Driver > Yes. 2. Click OK. 2. Click Next > Install. 3. The modem is ready for dial-up configuration. 3. Click Finish. Hot Key 1.
Page 173: Optional Drivers
Windows XP Information Optional Drivers Bluetooth Module See the pages indicated for the driver installation pro- Note: The operating system is the default setting for cedures for any modules included in your purchase op- Bluetooth control in WindowsXP, and does not require tion.
Page 174: Bluetooth Module
Windows XP Information Bluetooth Module The operating system’s Bluetooth Devices control panel is used to configure the Bluetooth settings in Windows XP, and therefore does not require a driver.. Bluetooth Data Transfer Note that transferring data between the computer and a Bluetooth enabled device is supported in one direction only (simultaneous data transfer is not supported).
Page 175 Windows XP Information Bluetooth Local Area Connection Icon If you want to display the Local Area Connection icon for the Bluetooth connection in the taskbar, set it up as follows: Access the Network Connections control panel in Windows (Start > Settings > Network Connections OR Start >...
Page 176: Bluetooth Configuration In Windows Xp
Windows XP Information Bluetooth Configuration in Windows XP Setup your Bluetooth Device so the Computer Can Find it 1. Turn your Bluetooth device (e.g. PDA, mobile phone etc.) on. Bluetooth Taskbar 2. Make the device discoverable (to do this check your device documentation). Icon To Turn the Bluetooth Module On If you cannot see the...
Page 177: To Add A Bluetooth Device
Windows XP Information To Add a Bluetooth Device Access the Bluetooth Devices control panel. Click Options (tab), and make sure that Allow Bluetooth devices to connect to this computer check box (Connections) has a tick inside it. Click Devices (tab), and then click Add. The Add Bluetooth Device Wizard will appear.
Page 178 Windows XP Information To Change Settings for the Bluetooth Device 1. Access the Bluetooth Devices control panel. 2. Click on the device you want to change and click Properties to: • Change the name of the device (click General, type a new name and click OK). •...
Page 179: Wireless Lan Module
Windows XP Information Wireless LAN Module If you have included an Intel® Wi-Fi Link 5100/5300 Series (802.11 a/g/n) WLAN or 3rd Party 802.11 b/g WLAN module in your purchase option, install the driver as outlined in the following pages. Download Prerequisite Files for Intel WLAN Before beginning the Intel®...
Page 180: Intel Wlan Driver Installation
Windows XP Information Intel WLAN Driver Installation 1. Insert the Device Drivers & Utilities + User’s Manual disc into the CD/DVD drive. 2. Option Drivers (button). 3. Click 1.Install WLAN Driver > Yes. 4. Click Next > Next to link to the required prerequisites on the internet. 5.
Page 181 Windows XP Information 18. Make sure that the WiFi On button is selected. Figure D - 22 - Intel PROSet Wireless WiFi Connection Utility Wireless LAN Module D - 33...
Page 182: 802.11B/G Wlan Driver Installation
Windows XP Information 802.11b/g WLAN Driver Installation 1. Insert the Device Drivers & Utilities + User’s Manual disc into the CD/DVD drive. Network 2. Option Drivers (button). Connection 3. Click 1.Install WLAN Driver > Yes. Use the Windows Net- 4. Choose the language you prefer and click Next. work Connections 5.
Page 183: Pc Camera Module
Windows XP Information PC Camera Module There PC Camera module uses the BisonCap application to capture video files. Taking Still Pictures PC Camera Driver Installation Double-click 1. Insert the Device Drivers & Utilities + User’s Manual disc into the CD/ Computer icon on the DVD drive.
Page 184 Windows XP Information PC Camera Audio Setup If you wish to capture video & audio with your camera, it is necessary to setup the audio recording options in Windows. Go to the Start menu and point to Settings (or just click Control Panel) and click Control Panel, then double- click the Sounds &...
Page 185 Windows XP Information BisonCap BisonCap is a video viewers for general purpose video viewing and testing, and for capturing video files to .avi format. Pre-Allocating File Space Run the BisonCap application from the Start > Programs/All Programs > Bison- Cam menu (it is recommended that you set the capture file before the capture You may pre-allocate process - see Set Capture File below).
Page 186 Windows XP Information Reducing Video File Size Note that capturing high resolution video files requires a substantial amount of disk space for each file. After recording video, check the video file size (right-click the file and select Properties) and the remaining free space on your hard disk (go to My Computer, right-click the hard disk, and select Properties) If necessary you can remove the recorded video file to a removable medium e.g.
Page 187 Windows XP Information Eliminating Screen Flicker If you find that the video screen in the BisonCap program is flickering, you can try to adjust the setting in the Video Capture Filter options. Run the BisonCap program. Go to Options and scroll down to select Video Capture Filter..Click either 50Hz or 60Hz under Frequency in Property Page (tab).
Page 188 Windows XP Information Zoom The BisonCap program allows you to zoom the camera in and out. 1. Run the BisonCap program. 2. Go to Zoom and select Zoom Out/Zoom In. 3. Go to Options and scroll down to select Setting (Use the slider to adjust the zoom level, and click OK to save the setting).
Page 189: Touch Screen Module
Windows XP Information Touch Screen Module If you have included a Touch Screen module in your purchase option, you should ob- Touch Screen Input tain a stylus pen to interact with the computer in the same way you would use a Device mouse (use a stylus pen to tap/double-tap on-screen buttons etc.).
Page 190 Windows XP Information Calibrating the Touch Screen 1. Click Start, and click Programs/All Programs and point to Touch Utilities (folder), and then click Touch Configuration program (or double-click the desktop icon 2. Click Calibration (button). Figure D - 26 Touch Screen Configuration D - 42 Touch Screen Module...
Page 191 Windows XP Information Click to choose the number of points in Calibration Precision, and then click Calibrate (button). Figure D - 27 Calibration Precision Use the stylus pen to touch the center of the cross sign until the OK sign appears in the center of the cross.
Page 192 Windows XP Information 5. When the Test Drawing appears, write on the screen to test the calibration (press the spacebar to clear any drawing, or Esc to exit). Figure D - 29 Test Drawing 6. Click Close to exit Calibration. 7.

EUROCOM Multimedia PC User Manual

Quick Start Guide

Features & Components

Power Management

Drivers & Utilities

BIOS Utilities

Upgrading the Computer

Modules & Options

Troubleshooting

Windows XP Information

Interface (Ports & Jacks)

Intel Video Driver Controls

Specifications

Quick Links

Need help?

Questions and answers

Related Manuals for EUROCOM Multimedia PC

Summary of Contents for EUROCOM Multimedia PC

Table of Contents