1. Manuals
  2. Brands
  3. EUROCOM Manuals
  4. Desktop
  5. LP200SC
  6. Service manual

EUROCOM LP200SC Service Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the LP200SC and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for EUROCOM LP200SC

Summary of Contents for EUROCOM LP200SC

  • Page 2: Preface

    REFACE ERVICE ANUAL LCD PC LP200SC/LP200ST...

  • Page 3: Notice

    ERVICE ANUAL OTICE The company reserves the right to revise this publication or to change its contents without notice. Information contained herein is for reference only and does not constitute a commitment on the part of the manufacturer or any subsequent vendor. They assume no responsibility or liability for any errors or inaccuracies that may appear in this publication nor are they in anyway responsible for any loss or damage resulting from the use (or misuse) of this publication.

  • Page 4: About This Manual

    REFACE BOUT ANUAL This manual is intended for service personnel who have completed sufficient training to undertake the maintenance and inspec- tion of personal computers. It is organized to allow you to look up basic information for servicing and/or upgrading components of the LCD PC. The following information is included: Chapter 1, Introduction, provides general information about the location of system elements and their specifications.

  • Page 5: Table Of Contents

    ERVICE ANUAL Table of Contents REFACE Notice ........................................II Trademarks......................................II About This Manual ....................................III Related Document .................................... III Table of Contents ..................................... IV 1. I HAPTER NTRODUCTION Overview ........................................ 1-1 Systm Specifications ..................................... 1-2 CPU ........................................1-2 Intel Celeron ....................................1-2 Intel Pentium III ..................................
  • Page 6 REFACE Temperature ....................................1-6 Humidity (non-condensing) ................................1-6 External Locator ....................................1-7 Front View ...................................... 1-7 Left View ......................................1-8 Right View ...................................... 1-9 Rear View ...................................... 1-10 System Board Overview ..................................1-11 Key Parts ......................................1-11 Cable Connectors, Switches & Jumpers ............................1-12 2.
  • Page 7 ERVICE ANUAL LED + Inverter Board Removal ................................ 2-19 Converter Board Removal ................................... 2-20 Speaker Removal ....................................2-21 Base Assembly Removal ..................................2-22 Power Supply Removal ..................................2-24 USB Board Removal .................................... 2-27 Hard Disk Drive Removal .................................. 2-28 A. P PPENDIX ISTS B.

  • Page 8: Introduction

    NTRODUCTION NTRODUCTION This manual covers the information you need to service or upgrade the LP200SC/ST LCD PC. Information about operating the computer (e.g. getting started, and the System Configuration Utility) is in the User’s Manual. Information about drivers (e.g. VGA &...

  • Page 9: Systm Specifications

    ERVICE ANUAL YSTEM PECIFICATIONS NTEL ELERON Socket Type Socket 370 (FCPGA/FCPGA2) Speed 533/600/633/667/700/733/766MHz (FSB66) 800/850/900/950MHz (FSB100) L1 cache (in CPU) 16KB code + 16KB data L2 cache (on die) 128KB NTEL ENTIUM Socket Type Socket 370 (FCPGA/FCPGA2) Speed 600/650/700/750/800/850/1100MHz (FSB100) 600/733/800/866/933/1000MHz (FSB133) L1 cache (in CPU) 16KB code + 16KB data...

  • Page 10: Bios

    NTRODUCTION BIOS Insyde 2Mb Flash ROM, APM 1.2, ACPI IDEO Controller built-in SiS630S Memory* SSMA Interface digital I/F Display built-in 15” LCD color TFT XGA (1024 x 768), 256K colors Port analog 15-pin VGA port for CRT *The system allocates or “shares” a portion of system memory for video use. “Shared” memory size is user-configurable via the SCU.

  • Page 11: Audio

    (x 2) Type II or (x 1) Type III Controller NSC99A3 Ports x 2 (LP200ST) x 4 (LP200SC) Serial (x 1) 9-pin, 16550A compatible (x 1) infrared (modes: IrDA, ASK, FIR) Parallel (x 1) 25-pin (modes: Standard AT, Bidirectional, ECP, EPP)

  • Page 12: Input

    NTRODUCTION NPUT Keyboard 104-key, AT-compatible, with special function keys Mouse Genius, scroll type, Microsoft compatible OMMUNICATIONS ODEM DEALER OPTION Type MDC, V.90, 56K (software-based) Output RJ-11 jack (on-board) Type built-in SiS630S Output RJ-45 jack (on-board) ECURITY BIOS Password Kensington Lock Slot OWER YSTEM Adapter...

  • Page 13: Environmental Specifications

    ERVICE ANUAL HYSICAL PECIFICATIONS Dimensions W: 369mm (14.5”) L: 384mm (15.1”) D: 175mm (6.9”) Weight 7.9Kg Panel Tilt to 15 Stand Swivel NVIRONMENTAL PECIFICATIONS EMPERATURE Operating C to 35 F to 95 Storage C to 65 C (14 F to 149 UMIDITY CONDENSING Operating...

  • Page 14: External Locator

    NTRODUCTION XTERNAL OCATOR The following figures show the external locations of the main features of the LCD PC’s system unit. RONT LP200SC LP200ST RONT . 1 – 1 1. 15” LCD 2. Speakers 3. FDD activity LED 4. CD-device activity LED 5.

  • Page 15: Left View

    ERVICE ANUAL . 1 - 2 1. PC Card (PCMCIA) socket 2. PC Card eject button 3. LCD brightness control 4. Microphone input jack 5. Line-in jack 6. Phones out jack 7. Volume control knob 8. HDD bay 1 – 8...

  • Page 16: Right View

    1. FDD bay 2. CD-Device bay 3. Emergency eject button - Use a probe (e.g. a straightened paper clip). 4. Eject button 5. Kensington Lock slot 6. AC-in port 7. two USB ports* (*LP200SC only) Right View 1 – 9...

  • Page 17: Rear View

    ERVICE ANUAL . 1 - 4 1. Carrying handle 2. Serial port (COM A) 3. Printer/Parallel port 4. VGA port 5. PS/2 mouse port 6. PS/2 keyboard port 7. IEEE 1394 port 8. USB ports (x2) 9. RJ-45 LAN port 10.

  • Page 18: System Board Overview

    NTRODUCTION YSTEM OARD VERVIEW ARTS ARTS Top View Bottom View . 1 - 5 1. CPU (Intel Pentium III or Celeron) 2. SiS630S Single Chipset (Core Logic, Audio, Video & LAN) 3. NSC99A3 Super I/O Controller 4. Flash ROM 5. two DIMM Sockets 6.

  • Page 19: Cable Connectors, Switches & Jumpers

    ERVICE ANUAL & J ABLE ONNECTORS WITCHES UMPERS & J ONNECTORS WITCHES UMPERS . 1 - 6 1. CN1 (Inverter Cable) 2. CN2 (Bluetooth Module) 3. CN5 (FDD Cable) 4. CN7 (System Fan Cable) 5. CN12 (USB Cable) 6. CN17 (Right Speaker Cable) 7.

  • Page 20: Disassembly

    ISASSEMBLY ISASSEMBLY This chapter provides step-by-step instructions for disassembling parts and subsystems. When it comes to reassembly, reverse the procedures (unless otherwise indicated). We suggest you completely review any procedure before you take the computer apart. CPU and Memory Upgrades: The upgrade procedures for CPU and system memory involve more than the component-specific removal and re- placement procedure.

  • Page 21: Maintenance Tools

    ERVICE ANUAL AINTENANCE OOLS The following tools are recommended when working on the LCD PC: • M3 Philips-head screwdriver • M2.5 Philips-head screwdriver (magnetized)* • M2 Philips-head screwdriver • Small flat-head screwdriver • Pair of needle-nose pliers • Anti-static wrist-strap * note Maintenance Precaution #3.

  • Page 22: Maintenance Precautions

    ISASSEMBLY AINTENANCE RECAUTIONS The following precautions are a reminder. To avoid personal injury or damage to the computer while performing a removal and/or replacement job, take the following precautions: Don't drop it. Perform your repairs and/or upgrades on a stable surface. If the computer falls, the case and other components could be damaged.

  • Page 23: Back Cover Removal

    ERVICE ANUAL OVER EMOVAL Place the system with its LCD display facing down. 2. Remove the 8 screws (A, B, C, D, E, F, G & H) which secure the Back Cover to the rest of the system. EMOVING CREWS FROM THE BACK OF THE SYSTEM .

  • Page 24: Cpu Removal

    ISASSEMBLY CPU R EMOVAL Part A Remove the Back Cover (page 2-4). Part B Note: If you want to upgrade the CPU, replace the old CPU with the upgraded one and also see the CPU Upgrade Notes on the next page. Unplug the Fan Cable from Connector CN10.

  • Page 25: Cpu Upgrade Notes

    ERVICE ANUAL CPU U PGRADE OTES After you install the upgraded CPU, check against the following table to see if you need to adjust switch settings. (Refer to Fig. 2- 4 for the location of the SW1 CPU Frequency Switch.) SW1 CPU F REQUENCY WITCH...

  • Page 26: Memory Module Removal

    ISASSEMBLY EMORY ODULE EMOVAL DIMM EMOVING Part A Remove the Back Cover (page 2-4). Part B Release the levers on the two ends of the DIMM slot. As you do so, DIMM EMOVING THE the module will rise slightly and remove the seated DIMM, one at .

  • Page 27: Modem Module Removal

    ERVICE ANUAL ODEM ODULE EMOVAL Part A Remove the Back Cover (page 2-4). Part B Remove 2 screws (A & B) securing the Modem Module to the System Board. 2. Disconnect the Modem Cable from Connector CN11 on the System Board. 3.

  • Page 28: Ieee 1394 Module Removal

    ISASSEMBLY IEEE 1394 M ODULE EMOVAL Part A Remove the Back Cover (page 2-4). Part B Disconnect the IEEE 1394 Cable from Connector CN19 on the System Board. 2. Remove the IEEE 1394 Module from Connector CN4 on the System Board. IEEE EMOVING THE 1394 M...

  • Page 29: Fdd Module Removal

    ERVICE ANUAL FDD M ODULE EMOVAL Part A Remove the Back Cover (page 2-4). Part B Remove 4 screws (A, B, C & D). 2. Separate the FDD Module from the rest of the system by disconnecting the FDD Cable from the System Board at Connector CN5. EMOVING THE ODULE .

  • Page 30: Cd Device Module Removal

    ISASSEMBLY CD D EVICE ODULE EMOVAL The CD device module can be the CD-ROM Module, DVD Module or CD-RW Module. Part A Remove the Back Cover (Page 2-4). Part B Remove 4 screws (A, B, C & D). 2. Separate the CD device module from the rest of the system by disconnecting the device cable from Connector CN23 on the System Board. EMOVING THE EVICE ODULE...

  • Page 31: Inverter Board Removal

    ERVICE ANUAL NVERTER OARD EMOVAL Part A Remove the Back Cover (Page 2-4). Part B Remove the Inverter Shielding Plate by removing 3 screws (A, B & C) which secure it to the rest of the system. (If you have already removed the FDD module, Screws A & B have already been removed during the process.) 2.

  • Page 32: I/O Bracket Removal

    ISASSEMBLY I/O B RACKET EMOVAL Part A Remove the Back Cover (page 2-4). 2. Remove the Modem Module (page 2-8). Part B Remove the I/O Bracket by removing 9 screws (A, B, C, D, E, F, G, H & I) which secure it to the rest of the system. (If you have already removed the CD device module, Screw A has already been removed during the process.) EMOVING THE RACKET...

  • Page 33: System Board Removal

    ERVICE ANUAL YSTEM OARD EMOVAL Part A Remove the Back Cover (page 2-4). Remove the Modem Module (page 2-8). Remove the I/O Bracket (page 2-13). Part B Disconnect the following 10 cables from the System Board: 10 Cables (C1) The Inverter Board to System Board (from Connector CN1). (If you have already removed the Inverter Board, the Inverter Cable has already been removed during the process.) (C2) The FDD Module to System Board (from Connector CN5).
  • Page 34 ISASSEMBLY 4. The System Board is connected to the rest of the system (i.e. LCD Module) via a board-to-board connector. Remove the System Board from the LCD Connector. System Board (Top View) Connector Module EMOVING THE YSTEM OARD . 2-15 CD Device System Board (Bottom View) Module...

  • Page 35: Lcd Module Removal

    ERVICE ANUAL LCD M ODULE EMOVAL Part A Remove the Back Cover (page 2-4). Remove the Modem Module (page 2-8). Remove the I/O Bracket (page 2-13). Part B Remove 7 screws (A, B, C, D, E, F & G). 2. Disconnect the following 7 cables. 7 Cables (C1 &...
  • Page 36 ISASSEMBLY EMOVING CREWS & 3 G ABLES ROUND IRES CN17 . 2-16 CN30 CN32 CN31 LCD Module Removal 2 – 17 2 – 17 2 – 17 2 – 17 2 – 17...
  • Page 37 ERVICE ANUAL 4. Remove the LCD Module. A. Remove 4 screws (A, B, C & D) to separate the Front Panel from the rest of the system. At this point the LCD Module is still connected to the System Board at a board-to-board connector and to the Converter Board. B.

  • Page 38: Led + Inverter Board Removal

    ISASSEMBLY LED + I NVERTER OARD EMOVAL Part A Remove the Back Cover (page 2-4). Remove the Modem Module (page 2-8). Remove the I/O Bracket (page 2-13). Perform Steps 1, 2 & 3 of Part B of the LCD Module Removal Procedure (page 2-16). Part B Separate the Front Panel from the rest of the system by removing 4 screws (A, B, C &...

  • Page 39: Converter Board Removal

    ERVICE ANUAL ONVERTER OARD EMOVAL Part A Remove the LCD Module (pages 2-16 ~ 2-18). Part B Separate the Converter Board from the rest of the system by removing Screw A. EMOVING THE ONVERTER OARD . 2-19 Converter Board 2 – 20 Converter Board Removal...

  • Page 40: Speaker Removal

    ISASSEMBLY PEAKER EMOVAL Part A Remove the Back Cover (page 2-4). Remove the Modem Module (page 2-8). Remove the I/O Bracket (page 2-13). Perform Steps 1, 2 & 3 of Part B of the LCD Module Removal Procedure (page 2-16). Part B Separate the Front Panel from the rest of the system by removing 4 screws (A, B, C &...

  • Page 41: Base Assembly Removal

    ERVICE ANUAL SSEMBLY EMOVAL Part A Remove the Back Cover (page 2-4). Remove the Modem Module (page 2-8). Remove the I/O Bracket (page 2-13). Part B Separate the Base Assembly from the rest of the system. A. Disconnect the following 3 cables and 3 ground wires from the System Board. 3 Cables (C1) The Power Supply to System Board (Connector CN16).
  • Page 42 ISASSEMBLY EPARATING THE SSEMBLY FROM THE CN12 CN16 YSTEM . 2-21 CN29 Base assembly Base Assembly Removal 2 – 23 2 – 23 2 – 23 2 – 23 2 – 23...

  • Page 43: Power Supply Removal

    ERVICE ANUAL OWER UPPLY EMOVAL The Power Supply is in the Base Assembly. Part A Remove the Base Assembly. (pages 2-22 & 2-23) Part B Remove the HDD Cartridge. A. Turn the Base Assembly upside down and remove Screw A. (Only the LP200ST has this screw.) B.
  • Page 44 ISASSEMBLY 2. Remove the Swivel Stand. A. Turn the Base Assembly upside down. B. Remove 4 screws (A, B, C & D). EMOVING THE WIVEL TAND . 2-23 3. Separate the Top Cover of the Base Assembly from the rest of the Base Assembly by removing 6 screws (A, B, C, D, E & F). Top Cover (Base Assembly) EMOVING THE OVER OF THE...
  • Page 45 ERVICE ANUAL 4. Separate the Power Supply from the rest of the Base Assembly by removing 4 screws (A, B, C & D). EMOVING THE OWER UPPLY . 2-25 Power Supply 2 – 26 Power Supply Removal...

  • Page 46: Usb Board Removal

    USB B OARD EMOVAL The USB Board is in the Base Assembly. (LP200SC only) Part A Remove the Base Assembly. (pages 2-22 & 2-23) Remove the HDD Cartridge. (Step 1 of Part B of the Power Supply Removal Procedure, page 2-24) Remove the Swivel Stand.

  • Page 47: Hard Disk Drive Removal

    ERVICE ANUAL RIVE EMOVAL The HDD is housed in the Base Assembly. Place the LCD PC with its LCD panel facing up and remove Screw A. (Only the LP200ST has this screw.) 2. Remove Screw B. A & B EMOVING CREWS .
  • Page 48 ISASSEMBLY 4. Turn the cartridge upside down. 5. Remove 4 screws (A, B, C & D) to separate the HDD Frame from the Cartridge Casing. EPARATING THE RAME FROM THE ARTRIDGE ASING . 2-29 6. Remove 6 screws (A, B, C, D, E & F) to separate the HDD from its frame. EPARATING THE FROM ITS RAME...
  • Page 49 ERVICE ANUAL OTES 2 – 30 Notes...

  • Page 50: Appendix A. Part Lists

    ISTS This appendix breaks down the LCD PC’s construction into a series of illustrations. The component part numbers are indicated in the tables opposite the drawings. It includes two sets of part lists for the LP200SC and LP200ST respectively. Note: This section indicates the manufacturer’s part numbers.
  • Page 51 ERVICE ANUAL LP200SC LP200SC F RONT SSEMBLY . A–1 Front Assembly A – 2...
  • Page 52 ISTS LP200SC F RONT SSEMBLY . A–2 Front Assembly A – 3...
  • Page 53 ERVICE ANUAL LP200SC F RONT III) SSEMBLY . A–3 Front Assembly A – 4...
  • Page 54 ISTS LP200SC F RONT SSEMBLY . A–4 Front Assembly A – 5...
  • Page 55 ERVICE ANUAL LP200SC B SSEMBLY . A–5 Back Assembly A – 6...
  • Page 56 ISTS LP200SC B SSEMBLY . A–6 Back Assembly A – 7...
  • Page 57 ERVICE ANUAL LP200SC B III) SSEMBLY . A–7 Back Assembly A – 8...
  • Page 58 ISTS LP200SC FDD ODULE . A–8 FDD Module A – 9...
  • Page 59 ERVICE ANUAL LP200SC CD D EVICE ODULE . A–9 CD Device Module A – 10...
  • Page 60 ISTS LP200SC B SSEMBLY . A–10 Base Assembly A – 11...
  • Page 61 ERVICE ANUAL LP200SC B SSEMBLY . A–11 Base Assembly A – 12...
  • Page 62 ISTS LP200SC HDD ODULE . A–12 HDD Module A – 13...
  • Page 63 ERVICE ANUAL LP200ST LP200ST F RONT SSEMBLY . A–13 Front Assembly A – 14...
  • Page 64 ISTS LP200ST F RONT SSEMBLY . A–14 Front Assembly A – 15...
  • Page 65 ERVICE ANUAL LP200ST F RONT III) SSEMBLY . A–15 Front Assembly A – 16...
  • Page 66 ISTS LP200ST F RONT SSEMBLY . A–16 Front Assembly A – 17...
  • Page 67 ERVICE ANUAL LP200ST B SSEMBLY . A–17 Back Assembly A – 18...
  • Page 68 ISTS LP200ST B SSEMBLY . A–18 Back Assembly A – 19...
  • Page 69 ERVICE ANUAL LP200ST B III) SSEMBLY . A–19 Back Assembly A – 20...
  • Page 70 ISTS LP200ST FDD ODULE . A–20 FDD Module A – 21...
  • Page 71 ERVICE ANUAL LP200ST CD D EVICE ODULE . A–21 CD Device Module A – 22...
  • Page 72 ISTS LP200ST B SSEMBLY . A–22 Base Assembly A – 23...
  • Page 73 ERVICE ANUAL LP200ST B SSEMBLY . A–23 Base Assembly A – 24...
  • Page 74 ISTS LP200ST HDD ODULE . A–24 HDD Module A – 25...
  • Page 75 ERVICE ANUAL OTES Notes A – 26...

  • Page 76: Witches And

    & J WITCHES UMPERS WITCHES AND UMPERS This appendix is about the system’s switches and jumpers. B – 1...
  • Page 77 ERVICE ANUAL OCATIONS The following figure shows the locations of the DIP Switches and Jumpers the system uses. You can access them after you remove the Back Cover (page 2-4). Be sure to turn OFF the system before you perform any part removal procedure. ’...
  • Page 78 & J WITCHES UMPERS ETTINGS CPU F SW1) REQUENCY WITCH ETTINGS WITCH I I P I I P I I I I I I I I P I I P I I P I I P I I I I I P I I P I I P I I I...

  • Page 79: Jumpers

    ERVICE ANUAL SW2 & J ANEL WTCH AND UMPER ETTINGS WTICH UMPER & & I T - i p ( i p ( CMOS C LEAR UMPER ETTINGS UMPER & & ) t l Switch and Jumper Settings B – 4...

  • Page 80: Circuit

    71-P2205-001A (This is an optional feature) External USB Board 71-P2206-001 (Only the LP200SC has this feature.) We have included the latest versions at the press time. If any board you want to service is newer than listed, please consult the nearest service center.
  • Page 81 ERVICE ANUAL YSTEM OARD System Block Diagram 3*CPUs 13*SDRAMs 6*PCIs CLOCK 1*48MHz GENERAT OR. SOCKET-370 24/48MHz P.2,3 2*REF HOST Bus DRAM Bus R.G.B. DIMM 1 DIMM 2 IDE Bus ZURAC2 PANEL T 0911XH IDE 1 IDE 2 (AT A-100) (AT A-100) P.11 P.10 P.11...
  • Page 82 IRCUIT IAGRAMS 3,4,5,19 +2.5V T20 T22 T27 T29 T31 T33 T35 T37 T25 T26 T28 T30 T32 T34 T36 T38 SLEWCTRL 110 1% R327 +2.5V 7,10,16,19 C248 C249 JUMPER OPEN RTTCTRL 110 1% R334 V_CORE 3,19 R335 For Future Compatibility Upgrate 0.1u_R 0.1u_R CLKREF...
  • Page 83 ERVICE ANUAL V_CORE HD#[0..63] HA#[3..31] V_CORE CB52 CB51 CB58 CB50 CB63 CB56 CB54 CB55 CB53 HD#56 HA#21 AA37 HD#61 VCC_CORE CPURST# AB32 HD#50 HA#25 VCC_CORE AC33 HD#60 HA#10 VCC_CORE AB34 RN59 8P4Rx56 HD#62 RN36 8P4Rx56 HA#15 VCC_CORE AD32 HD#58 HA#12 VCC_CORE AD34 HD#53...
  • Page 84 IRCUIT IAGRAMS Close to 630S 3,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20 MD[0..63] 2,3,5,19 MD[0..63] 8,11 CSA#[0..3] CSA#[0..3] CX20 CX18 R313 R309 CSB#[0..3] 1000p 1000p CSB#[0..3] 75 1% 75 1% MA[0..14] MA[0..14] GTLVREFA GTLVREFB GTLVREFA DQM[0..7] DQM[0..7] GTLVREFB R311 CX19 R308 CX17 1000p 1000p 150 1% 150 1% U2-1 630CCLK...
  • Page 85 ERVICE ANUAL (FOR INTERNAL PLL) 2,3,4,19 AD[0..31] Z0508 12,20 AD[0..31] +1.8V SB1.8V 0_0805 SB3V 6,13,15,16,19,20 +1.8V 16,19 CA174 CT33 3,4,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20 1000p 0.1u 10u/10V SERR# R281 4.7K U2-2 PERR# R280 4.7K 12,20 PERR# Close to 630S PREQ#2 AE13 PREQ#2 PREQ#[2] ICHRDY A ICHRDY A PREQ#1 PREQ#1...
  • Page 86 IRCUIT IAGRAMS B[0..7] R306 SB3V T82 T84 PLACE THESE CIRCUITS CLOSE TO SiS 630 T69 T71 T79 T80 R[0..7] PWRBTN# BEAD BK2125HS601 600ohm_0805 POWERSW# 16 G[0..7] CB44 CA178 COMP ROUT 0.1u GOUT DACAVDDC BOUT CT37 C192 CB45 U2-3 0.01u 10u/10V DACAVSSC AGPCLK BEAD BK2125HS601 600ohm_0805...
  • Page 87 ERVICE ANUAL SIS-630S CLOCK SETUP TABLE 10K_R Frequency Selection Board ID. BSEL0# (FS3) (FS2) (FS1) (FS0) SDRAM (MHz) (MHz) (MHz) (MHz) 10K_R BSEL1# 66.7 33.33 14.318 33.33 14.318 R262 2.7K Z0705 R169 10K_R 33.33 14.318 R261 2.7K Z0706 R170 10K_R 33.33 14.318 R260...
  • Page 88 IRCUIT IAGRAMS 3,4,5,6,7,9,10,11,12,13,14,15,16,17,18,19,20 MD[0..63] 4,11 MD[0..63] MA[0..14] MA[0..14] DQM[0..7] DQM[0..7] DIM3V DIM3V DIM3V R446 R447 2.2K 0_1206 0_1206 2.2K CT21 CT10 DIM3V CA49 CA75 CA24 CA20 CA10 10u/10V 10u/10V 0.1u 0.1u 0.1u 0.1u 0.1u 0.1u Z0823 CT19 Z0855 A[0] WP/NC A[0] WP/NC CA68...
  • Page 89 ERVICE ANUAL 3,11,12,14,15,16,17,18,19,20 2N7002 3,4,5,6,7,8,10,11,12,13,14,15,16,17,18,19,20 Z0940 DDCDATA 6,10 2N7002 2N7002 Z0941 DDCCLK 6,10 R229 Z0901 Z0903 BEAD BK1608HS601 600ohm Z0919 CN26 VSY NC C146 C145 Z0926 R230 R227 2N7002 220p_R 220p_R BEAD BK1608HS601 600ohm R228 Z0902 Z0904 Z0920 HSY NC Z0943 Z0921 T146...
  • Page 90 IRCUIT IAGRAMS Z1033 RN45 5,12,20 PCIRST#2 DDCCLK 8P4Rx22 INT#D Z1034 DDCDATA PRA7 T149 R443 Z1053 630DE PRA6 T148 T150 R441 Z1054 IAHSY NC PRA5 R442 Z1055 T152 T154 T156 T158 IAVSY NC PRA4 T151 T153 T155 T157 T159 VGCLK PRA3 ZURACPCLK PRA2 PRA1...
  • Page 91 ERVICE ANUAL ON=1=H OFF=0=L SW2-1 SW2-2 SW2-3 SW2-4 IDEDA[0..15] CHI MEI M150X1 PCIRST#1 5,14 PCIRST#1 SHARP LQ150X1DG51 R252 CN29 HYUNDAI HT15TX11-200-HYU. RN17 RN16 8P4Rx33 8P4Rx33 IDEDA6 IDEDA6A IDEDA7A IDEDA8A IDEDA4A IDEDA4 HYUNDAI HT15TX11-200-TI IDEDA9 IDEDA9A IDEDA6A IDEDA9A IDEDA11A IDEDA11 IDEDA7 IDEDA7A IDEDA5A IDEDA10A...
  • Page 92 IRCUIT IAGRAMS System Board (71-P2T00-005) - Sheet 12 of 20 C – 13...
  • Page 93 ERVICE ANUAL Z1301 3,4,5,6,7,8,9,10,11,12,14,15,16,17,18,19,20 R160 R161 SB3V 5,6,15,16,19,20 0.1u 49.9 1% 49.9 1% C257 CN14 0805 0805 10p_R RJ-45 CONNECTOR TOP VIEW TPO+ Z1362 Z1363 GND1 GND1 TPO- Z1364 Z1365 GND2 GND2 TPI+ Z1366 Z1367 GND3 GND3 TPI- Z1310 ZCY S51R5-M6PT_R GND4 GND4 Z1303...
  • Page 94 IRCUIT IAGRAMS INDEX# R191 MEMR# R181 LAD[0..3] LAD[0..3] BIOSCS# R173 LAD0 FDD-LED# FDD-LED# LAD0 DR0# LAD1 MTR0# PWRDN# R184 LAD1 MTR0# LAD2 DIR# LAD2 DIR# LAD3 STEP# LAD3 SETP# WDATA# WDATA# CLKRUN# WGATE# CLKRUN#/GPIO36 WGATE# RN10 PWRDN# HDSEL# LPCPD# HDSEL# CF15 CF17 393PCLK...
  • Page 95 ERVICE ANUAL CN27 DTR# DTR1# SOUT SOUT1 DCDA# R410 BEAD BK1608LL121 120ohm DCD# RTS# RTS1# DSRA# R409 DSR# BEAD BK1608LL121 120ohm RXDA R408 BEAD BK1608LL121 120ohm DSR# DSR1# RTSA# R407 BEAD BK1608LL121 120ohm RTS# RING# RING1# TXDA R406 SOUT BEAD BK1608LL121 120ohm SIN1 CTSA# R405...
  • Page 96 IRCUIT IAGRAMS +1.8V +2.5V MUST CLOSE TO CHIP RTCVDD PIN The RTCVDD is 1.8V PWRGOOD POWEROK 3 Z1602 SB3V VRMPWRGD 19 1N4148 1N4148 Z1604 RESET-SW# R255 RTCVDD Z1601 Z1603 Z1605 PWRGD 1N4148 1N4148 1N4148 1N4148 1N4148 BAT1 3V/210mah Z1606 BATOK CA26 7407 0.1u...
  • Page 97 ERVICE ANUAL R234 3.9K +A5V R128 0_0805 CA109 U18A TDA1308 0.1u R235 AGND R430 3.9K V_in V_out +A5V 3.9K SOUND-L CB31 Z1701 Z1702 HEADOUT-L ENABLE +A5V CT20 CA69 CA72 CB14 10u/10V 0.1u 0.1u U18B AMC7630_R TDA1308 R224 Z1703 +A5V R431 SOUND-R 100K CB75...
  • Page 98 IRCUIT IAGRAMS +12V 11,12,13,16,19 R168 Z1843 3,9,11,12,14,15,16,17,19,20 +2.25VREF +A12V +2.25VREF CF16 T217 0_0805 R175 7.5K +12V +A5V 4.7u/16V CA106 10u/16V 10u/16V 0.1u CN13 R177 Z1847 7.5K Z1844 AGND BEAD HB-1H1608-601T02 600ohm R179 CA88 0.1u Z1842 Z1841 Z1840 R209 MIC-IN AMP_L Z1802 CB28 Z1801...
  • Page 99 ERVICE ANUAL +12V +12V 11,12,13,16,18 +12V +1.8V +2.5V 3,9,11,12,14,15,16,17,18,20 SB5V 3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,20 R377 +2.5V 2,7,10,16 1K_0805 +1.8V 5,16 C276 C277 C278 C279 C280 C281 C284 C288 C289 C290 +1.5V CA231 JUMPER OPEN V_CORE VRMPWRGD 0.1u 0.1u 0.1u 0.1u 0.1u 0.1u 0.1u 0.1u 0.1u 0.1u...
  • Page 100 IRCUIT IAGRAMS System Board (71-P2T00-005) - Sheet 20 of 20 C – 21...
  • Page 101 ERVICE ANUAL NVERTER OARD 1.5A 0.1u 0.1u 1.5A 1.5A Z0101 Z0103 Z0108 Z0116 LIGHT-ON 100uH_SDS1208 Z0139 4431 PIN1A=Z0108 2.2K_1206 0.1u 0.1u PIN2A=Z0116 HEADER 5X2 0.1u_0805 Z0106 470_0805 CLOSE_2A Z0120 Z0122 18p/3KV Z0123 330P_0805 1000u/16V(6.3*11) DTB114 Z1040 SGND SD1782 EC2QS04 PGND Z0104 Z0107 0.15u/100V...
  • Page 102 IRCUIT IAGRAMS LED + I NVERTER OARD 1.5A Z0101 Z0103 Z0108 Z0116 100uH_SDS1208 LIGHT-ON 0.1u 0.1u 4431 PIN1A=Z0108 2.2K_1206 Z0102 PIN2A=Z0116 470_0805 Z0106 Z0120 Z0122 18p/3KV Z0123 330P_0805 INVERT ER 1000u/16V(6.3*11) DTB114 Z0139 Z0104 SD1782 PIN9=GND_EARTH Z0107 0.15u/100V Z0125 EC2QS04 4672 150_0805 Z0119...
  • Page 103 ERVICE ANUAL ONVERTER OARD YUNDAI PANELS Converter Board - for Hyundai panels (71-P2T03-003) C – 24...
  • Page 104 IRCUIT IAGRAMS ONVERTER OARD PANELS Converter Board - for LG panels (71-P2T04-002) C – 25...
  • Page 105 ERVICE ANUAL IEEE1394 E XTENSION OPTIONAL CN 1 Z0101 PLLVD D PLEASE CLOSE IC Z0102 D VDD 1 D VDD 2 TSB41LV01 D VDD 3 D VDD 4 .1U F .1U F .1U F .1U F .1U F 6.34K 1% INT#B INT#B 2 AVDD 1...
  • Page 106 IRCUIT IAGRAMS USB B XTERNAL OARD (LP200SC only) CN 1 CN 2 U V2- 0(0603) U SB-PLUG 0(0603) UV2+ V+_OUT1 V+_OUT1 DATA_L1 DATA_L1 DATA_H 1 DATA_H 1 GN D V+_OUT2 V+_OUT2 DATA_L2 DATA_L2 DATA_H 2 GN D U V3- 0(0603)
  • Page 107 ERVICE ANUAL OTES Notes C – 28...

This manual is also suitable for:

Lp200st

Table of Contents