Shift Rod; Hardware Pack - Craftsman 247.885550 Owner's Manual

ASSEMBLY INSTRUCTiONs ................................
i i,,i iii IIIHII II IIIIIII1,111,111,11,1 111111,
IMPORTANT: This unit has been shipped WITH- Tools Required for Assembly:
OUT GASOLINE or OIL, After assembly, see oper- 1/2" Wrench*
ation section of this manual for proper fuel and (2) 7/16" Wrenches*
engine oil recommendations. Pair of Pliers
*or Adjustable Wrenches
NOTE: To determine right and left hand sides of your
snow thrower, stand behind it in the normal operating Loose Parts in Carton:
position° (t) Handle Panel and Chute Assembly
TO REMOVE SNOW THROWER FROM CARTON
(attached by
cable)
Cut the corners of the carton, Remove all packing (1) Right Hand Handle
inserts. Roll snow thrower out of the carton, Make (1) Left Hand HandJe
certain all parts and literature have been removed (1) Chute Crank Assembly
before the carton is discarded. (1) Shift Rod
CONTENTS OFHARDWARE PACK
Lay out the hardware according to the illustration for identification purposes, Part numbers are shown in
parentheses
_ ATTACHING THE HANDLE ASSEMBLY
Hex Bolts {]CZ0(_ZZ0
5t16-18 x %3/4" _
_/_ Hex Nuts" L_ _
_V_J _.--1/4-20 Thread _
(736-0287) _-_
_ Rex Bolts
_"--- 5/16-18 X518"
_ Long (710-0538} Handle Tabs
(784-5599}
(_-_ Lock Cupped
'_J_.--Washers
_ 5t16" I,D, (735-0270)Washers* [ ..-. \'_vJ
(736-011 g) 114" I.D,"-'-"_
Hex Bolts* _LJjJ
1/4-20 x v
1 Bolts_
5116:18x [] l_J
1-1/2 Long _
(710-12S0) _ @
Cupped Washers*_-._(F'_
51t6' I,D.
(736-0242)
HeX Nuts*
5116-18 Thread (712-0267)-=.O _ _
*May be preassembled on your unit.
_ ATTACHING THE CHUTE CRANK
Flat Washers
3t8" LD, x 5/8" O.D, Hex Bolt tT-17,7_
5f16-18 x 1-1t2"
Long
(710-0442}
_
Lock Washer
T 5/16" LD, _'t'_
(736-011_)
Hex Nut
Cotter Pin
5116-18 Thread----_{'C)]
(714-0507) (712-0267)
B_ ATTACHING THE CHUTE ASSEMBLY
Hex Bolts
114-20 x 314" Long
(710-3015)
_)(_7,('_ Hex Lock Nuts
"=" _'-_ 1/4-20 Thread
"- Chute Range
Keepers
(731-0851 )
D_ ATTACHING THE.. SHIFT ROD
AND CLUTCH CABLES
E_ AUGER SHEAR BOLTS
tT"'-f7 ri-'77
The _ug_rs _re securedto the spiral shaft w_h _wohex boltsand hex _
insertlocknuts.ff you hit a _orr_lgn o bje¢_0rtc_ I,_m,Ih_ snowthrower I s _._ _._ Hex Botts
des]gffed sothat tha hex bo_ts will$he_r.Tworeplacement h ex l_ffs and _ 5116-18 X 1-1/2"
nuls are provided f_ryour cQnvenlence S t_re}n_ 5_fep_ace ortl_l _ eeded _ Long
NN (71o.o o)
Ferrule Hairpin Ctips--'-_ _)
*_'(711-0677) (714-0104) _'_
_ /"_ Flat Washers
_j"_-5116' LD. x 518" O.D°
(736-0264)
(_4-_Sprtng Washer Hex Nuts
5116" LO,. (Coma with
(736-0271) Clutch Cables
Hex Lock Nuts
5t16-18 Thread
(712-0158)