Options; Location Requirements - Whirlpool Duet WFW9470WL00 Use & Care Manual

Alternate Parts
Your installation may require additional parts. If you are interested
in purchasing one of the items listed here, call the toll-free number
on the cover or in the "Assistance or Service" section.
If You Have You Will Need to Buy
Laundry tub or Sump pump system (if not already
standpipe taller available)
than 96" (2.4 m)
Overhead sewer Standard 20 gal. (76 L), 30" (762 mm) tall
drain tub or utility sink and sump pump
(available from local plumbing suppliers)
Floor drain Siphon break, Part Number 285834;
additional drain hose Part Number
8318155; and connector kit, Part
Number 285835
Drain hose too 4 ft (1.2 m) drain hose extension kit,
short Part Number 285863
Water faucets 2 longer water fill hoses: 6 ft (1.8 m)
beyond reach of fill Part Number 76314, 10 ft (3.0 m)
hoses Part Number 350008
Pedestal
You have the option of purchasing pedestals of different heights
separately for this washer. You may select a 10" (254 mm) or a
15.5" (394 mm) pedestal. These pedestals will add to the total
height of the washer for a total height of approximately
48" (1219 mm) or 53.5" (1359 mm).
A B
A. 10" (254 ram) pedestal
B. 15.5" (394 ram) pedestal
To order, call the dealer from whom you purchased your washer or
refer to the "Assistance or Service" section.
Pedestal Color Part Number
Height
10" (254 mm) White WHP1000SQ
10" (254 ram) Black WHP1000SB
10" (254 ram) Diamond Dust (Silver) WHPIOOOSU
15.5" (394 ram) White XHP1550VW
15.5" (394 ram) Black XHP1550VB
15.5" (394 ram) Diamond Dust (Silver) XHP1550VU
Pedestal Color Part Number
Height
15.5" (394 ram) NewAspen (Light Green) XHP1550VA
15.5" (394 ram) Tuscan Chestnut XHP1550VC
15.5" (394 ram) Ocean Blue XHP1550VE
15.5" (394 ram) Cranberry Red XHP1550WR
15.5" (394 ram) Lunar Silver XHP1550WL
Stack Kit
Are you planning to stack your washer and dryer? To do so you
will need to purchase a Stack Kit.
To order, call the dealer from whom you purchased your dryer or
refer to the "Assistance or Service" section. Ask for Part
Number 8541503.
Selecting the proper location for your washer improves
performance and minimizes noise and possible washer "walk."
Your washer can be installed under a custom counter, or in a
basement, laundry room, closet, or recessed area. See "Drain
System."
Companion appliance location requirements should also be
considered. Proper installation is your responsibility.
You will need
• A water heater set to deliver 120°F (49°C) water to the washer.
A grounded electrical outlet located within 6 ft (1.8 m) of
where the power cord is attached to the back of the washer.
See "Electrical Requirements."
Hot and cold water faucets located within 4 ft (1.2 m) of the
hot and cold water fill valves, and water pressure of
20-100 psi (137.9-689.6 kPa).
A level floor with a maximum slope of 1" (25 mm) under entire
washer. Installing the washer on soft floor surfaces, such as
carpets or surfaces with foam backing, is not recommended.
A sturdy and solid floor to support the washer with a total
weight (water and load) of 400 Ibs (180 kg).
Do not operate your washer in temperatures below 32°F (0°C).
Some water can remain in the washer and can cause damage in
low temperatures.
Installation clearances
• The location must be large enough to allow the washer door to
be fully opened.
Additional spacing should be considered for ease of
installation and servicing.
Additional clearances might be required for wall, door, and
floor moldings.
Additional spacing of 1" (25 mm) on all sides of the washer is
recommended to reduce noise transfer.
Companion appliance spacing should also be considered.
4