Table of Contents
Advertisement
User manual
OPTIONS
! If the selected function is incompatible with the set programme, the incompatibility will be signalled by a buzzer (3 beeps).
! If the selected function is incompatible with another previously set function the function will not be enabled.
CLEAN+
Clean+ is an option working on 3 different levels
(Intensive, Daily and Fast) that are specially designed to
set the right washing action, depending on your cleaning
needs:
Intensive
: this option is designed for high levels of
dirtiness, removing most stubborn stains.
Daily
: this option is designed to remove everyday stains.
Fast
: this option is designed to remove lightly soiled
stains.
INTENSIVE RINSE
By selecting this option, the efficiency of the rinse is
increased and optimal detergent removal is guaranteed.
It is particularly useful for sensitive skin. Press the button
once, two or three times to select an additional 1
2
or 3
rinses after the standard cycle rinse and
remove all traces of detergent. Press the button again
to go back to the "Normal rinse" rinse type.
START DELAY
To set the selected programme to start at a later time, press
the button to set the desired delay time. The symbol
lights on the display when this function is enabled.
Upto 24 hours. To cancel the delayed start, press the button
again until the value, ''0'' is shown on the display.
FUNCTIONS
ON/OFF
To switch on the washing machine: press the "ON/
OFF"
button, the "Start/Pause"
switch off the washing machine during the wash cycle,
press and hold the button for approximately 3 seconds. If
the button is pressed briefly or accidentally the machine
will not switch off.
To switch off the washing machine after programme end:
press the "ON/OFF"
button until the lights go off.
KNOB
To select and confirm programmes. Turn to
select.
START/PAUSE
To start the programme, after you have finished
your settings. To pause a running programme. To continue
a paused programme.
KEY LOCK
To lock the control panel, press and hold the "Key
lock"
button for approximately 3 seconds. The symbol
will light up on the display to indicate that the control
panel has been locked (with the exception of the "ON/
OFF"
button). This prevents unintentional changes to
programmes, especially with children near the machine. To
unlock the control panel, press and hold the "Key lock"
button for approximately 3 seconds.
8
,
BLEACHING
If you wish to bleach the laundry, load the washing machine
button light up. To
and set the "Rinse & Spin" programme .
Start the machine and wait for it to complete the first water
filling cycle (roughly 2 minutes) . ut the machine in pause
mode by pressing the "Start/Pause"
the detergent drawer and pour the bleach (observe the
recommended doses indicated on the package) into the
main wash compartment where the partition was previously
mounted . estart the cycle by pressing the "Start/Pause"
button .
If desired, it is possible to add fabric softener into the
appropriate compartment of the detergent drawer .
DEMO MODE
This function is only used for sales presentations . By this
you can interact with washing machine and see it working
without water . To enter Demo mode, switch the washing
machine ON and OFF again . Press and hold "Start/Pause"
button and hold both buttons for 10 seconds .
To deactivate this function, switch the washing machine
OFF . Then press and hold "Start/Pause"
within 5 seconds press also "ON/OFF"
hold both buttons for 2 seconds .
FRESHCARE+
This option enhances washing performance by
generating steam to inhibit the proliferation of the
main bad odour sources inside the machine. After steam
phase, the washing machine will perform gentle tumbling
through slow rotations of the drum. FreshCare+ option
starts after the cycle ends for a maximum duration of 6h
and you can interrupt it at any time by pressing any
button on control panel or turning the knob. Wait
around 5 minutes before door can be opened.
TEMPERATURE
Every programme has a predefined temperature. If
you want to change the temperature, press the
"temperature" button. The value appears on the display.
SPIN
Every programme has a predefined spin speed. If you want
to change the spin speed, press the "Spin" Speed button.
The value appears on the display.
button, then within 5 seconds press also "ON/OFF"
button, open
button,
button and
Advertisement
Table of Contents
