Table of Contents
Advertisement
Section5: Maintenance
m'
!_r_rl.,lq_ql_qel
Beforeinspecting,cleaning or servicingthe machine, shutoff engine, wait for movingparts to stop, dis-
t _)
connectsparkplug wire and movewire away from spark plug.
Failure to follow these instructionscan result in seriouspersonal injuryor propertydamage.
If the engine is running poorly or has low
power whiletilling, an adjustment to the
carburetor may solve the problem. How-
ever, first inspect and service the spark
plug and the air filter before making a
carburetor adjustment. If the engine con-
tinues to run poorly (and the fuel mixture
is fresh), proceedto the following carbu-
retor adjustment instructions.This fac-
tory-engineered instruction is designedto
provide continued optimum engine oper-
ating performance after the engine break-
in period, which is approximately 5 to 10
hours. The adjustment, when properly
performed as described below, will not
void the engine warranty. A common
screwdriver is needed. If you prefer, see
an authorized engine dealer for
adjustment.
Prior to Carburetor Adjustment:
The temperature of the muffler and adja-
cent engine areas may exceed 150°F
(65°C). Contact may causeburns. Avoid
these areas.
Remove the spark plug
lead and groundthe lead to the engine to
preventaccidentalstarts and fires.
Failure to do this could cause personal
injury.
1. Let engine cool for 30 minutes before
continuing.
2. From the operator's position behind the
handlebars, lay the machine down on its
left side (muffler side).
CarburetorAdjustment:
1. Locate the carburetor idle mixture
screw (Figure 15). It is directly under the
air filter and is black.
Do Not AdjustSilver-ColoredScrew.
2. Turn the black idle mixture screw 1/16
of a turn clockwise.
3. Return the unit to its normal upright
operating position and reconnect the
spark plug wire.
If the engine continues to run poorly, con-
tact an authorized engine dealer.
Spark Plug
Inspect the spark plug annually or every
100 operating hours according to the
instructions in the separate Engine
Owner's Manual. Checkthat the gap is set
at .030". For replacement use Champion
RCJ-6Yor equivalent (a resistor spark
plug must be used for replacement).
Cooling System
It is important to frequently check and
remove grass clippings, dirt and other
debris that accumulateson the engine,
cooling fins, air intake screen and on
levers and linkages. This helps to ensure
adequateair cooling and correct engine
speed.
Figure 16:Remove ring lockpin (,4) to take
off tines.
IMPORTANT:The ring lock pin (A, Figure
16) is under spring tension - wear gloves
to protect your fingers when removing or
replacing the ring lock pin.
TINE REMOVAL
AND INSTALLATION
Avoid contact with the cutting edges on
the tines.
To avoid personal injurywhen removing
or installing tines, wear heavy work
gloves. The engine must be off, all
moving parts stopped, and the spark
plug wire disconnected from the spark
plug and movedaway from the plug.
The tines will wear with use and they
should be replaced if tilling seems to take
longer than usual or if the soil is not
being mixed as thoroughly. Also, in addi-
tion to the standard 10"tilling width tine
configuration, the tines can be arranged
in two other configurations: (1) A narrow,
41/2"tilling width for smaller areasand (2)
A special pattern for stony soil conditions.
Arranging Tines for Narrow Tilling
1. Prop the machine forward so it rests
on the front of the tubular carrying
handle. The work surface should be flat
and firm.
2. Flip open the ring (A, Figure 16) on the
left side ring lock pin and remove the ring
lock pin.
3. Removethe outer tine section (do not
remove inner tine section) and mark it as
to which side it is from (left or right) and
whether it's an outer or inner tine section.
4. Slide one of the long bushings (B,
Figure 17), provided with the unit, onto
the shaft. Insert the ring lock pin through
the rounded side of the tine shaft and
snap the ring down over the shaft (see
DETAIL- Ring Lock Pin, Figure 4, in
Section 2).
5. Repeatthis procedure on the opposite
side.
Primer Bulb
Primer Line
--
Idle Speed Screw (Silver)
Idle Mixture Screw (Black)
Fuel Line
12
Figure 15: Idle Mixture Screw can be adjusted.
Advertisement
Table of Contents
