Samsung series 7 7000 User Manual page 34

Advanced Features
Network Setup (Manual) ....................................................................................................................... SWL connect ...........................
If the other methods do not work, you need to enter the
Network setting values manually.
Getting the Network Connection Values
To get the Network connection values on most Windows
computers, follow these steps:
1. Right click the Network icon on the bottom right of the
screen.
2. in the pop-up menu, click Status.
3. Qn the dialog that appears, click the Support tab.
4. Qn the Support tab, click the Details button. The
Network settings are displayed.
How to set up manually
To enter the Network connection values manually, follow
these steps:
1. Follow Steps 1 through 6 in the "How to set up using
PBC (WPS)" (p. 32).
2. Press the _' button to select mnternet Protocol Setup,
and then press the ENTERE_ button. Press the A
or T button to select Manual, and then press the
ENTER I_ button.
3. Press the • button to go to the first entry field (IP
Address).
4. Use the number buttons to enter numbers.
5. When done with each field, use the _ button to move
successively to the next field. You can also use the other
arrow buttons to move up, down, and back.
6. Enter the IP Address, Subnet Mask, and Gateway
values.
7. Press the A or _' button to go to DNS.
8. Press the T button to go to the first DNS entry field.
Enter the numbers as above.
9. When done, press the A button to go to Select a
Network. Select your network, and then press the
ENTER C_ button.
10. Go to Step 4 in the "How to set up automatically" (p.
32), and follow the directions from that point on.
SWL (Samsung Wireless Link)
This function lets you connect a Samsung device that
supports the PBC (WPS) to your TV, You can connect
devices to the TV even if a sharer is not connected to the T_.
To use the Internet@TV, the AP (access point) must be
connected to the wireless network.
You can directly connect a device that supports the PBC
(WPS)to the TV.
This function is available when SWL (Samsung
Wireless Link) is set to On.
How to connect Samsung Wireless Link
For the procedures to establish a connection, refer to the
following:
1. Follow Steps 1 through 5 in the "How to set up using
PBC (WPS)" (p. 32).
2. Select Samsung Wireless Link by using the _' button
and press the ENTERC_ button to turn it On.
3. Select SWL connect by using the T button and press
the ENTERE_ button.
4. If the "Press the PBC button on the device which
supports PBC button to connect within 120
seconds" message appears, press the PBC button on
the device to connect.
For more information, refer to the wireless network
setup manual of the device to be connected.
5. If the device is connected properly to the TV after
starting count on message box then message box will
be disappeared automatically.
If the connection fails, please retry after 2 minutes.
If Your -iV Fails to Connect to the Internet
Your TV may not be able to connect to the Internet
because your ISP has permanently registered the
MAC address (a unique identifying number) of your
PC or modem, which it then authenticates each time
you connect to the Internet as a way of preventing
unauthorized access. As your TV has a different MAC
address, your ISP can not authenticate its MAC address,
and your TV can not connect.
To resolve this problem, ask your ISP about the
procedures required to connect devices other than a PC
(such as your TV) to the Internet.
If your Internet service provider requires an ID or password
to connect to the Internet, your TV may not be able to
connect to the Internet. If this is the case, you must enter
your ID or password when connecting to the Internet.
The internet connection may fail because of a firewall
problem. If this is the case, contact your Internet service
provider.
If you cannot connect to the Internet even after you have
followed the procedures of your Internet service provider,
please contact Samsung Electronics at 1-800-SAMSUNG.
If a Samsung Wireless Lan Adaptor is connected to the
USB 2 port, the network may not operate normally. We
recommend to connecting it to the USB 1 (HDD} port.
Only sharers using the 2.4 Ghz band are supported.
Sharers using the 5 Ghz band are not supported.
4 English