Advertisement
Available languages
Available languages
Tools needed
for securing
the drain
hose and leveling
the washer:
•
Adjustable
or open end
•
Wood
block
wrench
%6" (14 mm)
•
Ruler or measuring
tape
•
level
Parts supplied:
A
B
A. Beaded tie strap
B. Front leveling f_'et with nuts (2)
Alternate
Parts
Your installation
may require
additional
parts. For ordering
information,
please
refer to the
toll-free
phone
numbers
on the front page of the Use and Care Guide.
If You Have:
You Will
Need to Buy:
laundry
tub or standpipe
Sump pump
system (if not already
aw_ilable)
taller than 96" (2.4 m)
1" (2.5 cm) diameter
1 _/4" (3.2 cm) diameter
to 1" (2.5 cm) diameter
standpipe
standpipe
adapter, Part Number
280130
Overhead
sewer
Standard
20 gal. (76 [ ) 39" (99 cm) tall drain
tub or utility
sink, sump pump
and connectors
(available
from local
plumbing
suppliers)
Floor drain
Siphon break kit, Part Number
280129;
additional
drain
hose, Part Number
3357090
Water faucets beyond
reach
2 longer
water fill hoses:
of fill hoses
6 ft (1.8 m) Part Number
76314,
] 0 ft (3.0 m) Part Number
350008
Drain hose too short
Kit Part Number
280]
31
lint
clogged
drain
[)rain
protector,
Part Number
367031
Selecting the proper location
for your washer improves
performance
and minimizes
noise and
possible washer
"walk."
Your washer
can be installed
in a basement,
laundry
room, closet, or recessed
area. See
"[:)rain
System."
IMPORTANT:
Do not install or store the washer
where
it will be exposed
to the weather.
Proper installation
is your responsibility.
You will need:
•
A water heater set to deliver
120°F (49°C) water to the washer.
•
A grounded
electrical
outlet
located
within
4 ft (1.2 m) of where the power
cord is
attached
to the back of the washer. See "Electrical
Requirements."
•
Hot and cold water faucets
located
within
3 ft (90 cm) of the hot and cold water fill
valves, and water pressure of %100 psi (34.5-690
kPa). Washers
with triple
dispensers
require 20-100
psi (138-690
kPa) for best performance.
•
A level floor with
a maximum
slope of 1" (2.5 cm) under entire
washer.
Installing
the
washer on carpeting
is not recommended.
•
A sturdy floor to support
the washer weight
(washer, water and load) of 315 Ibs (143 kgs).
Do not store or operate
your washer
in temperatures
at or below
32°F (0°C). Some water can
remain
in the washer
and can cause damage
in low temperatures.
See "Washer
Care."
ecessed
area or d oset ,nsta,a.on
The dimensions
shown
are for the recommended
spacing
allowed
(A and g), except
the closet
door
ventilation
openings.
The dimensions
shown
for the closet
door
ventilation
openings
(C)
are the minimum
required.
19" 5_-
(4&3 _rn)
2L_
n
olo
1_I rnax,
_48 in_
(310¢m_)
-
.2
24n -
(1__rn _)
m
(0crn)
(68.6crn)
(0crn)
(2.Scrn) (64.8cm)
(10.2crn)
A
B
(7.6 c m)
NNN-
__
_
3_'
17,6 _[11)
--3-
C
A. Front view
B. Side view
(7. Closet door
with
w_nts
•
Additional
spacing
should
be considered
for ease of installation
and servicing.
•
Additional
clearances
may be required
for wall, door and floor
moldings.
•
Additional
spacing
of 1" (2.5 cm) on all sides of the washer
is recommended
to reduce
noise transfer.
•
If a closet door is installed,
the minimum
air openings
in the top and bottom
of the door
are required
(C). [ ouvered
doors
with air openings
in the top and bottom
are acceptable.
•
Companion
appliance
spacing
should
also be considered.
5
Advertisement
