Philips 30PW862H Directions For Use Manual page 78

T_e AV4 Input Jacks provide High Definition Video Inputs at
080i o1"480p,/'or accessories like a HD Receiver and Digital
DVD Players. Using the color diffk, rence signals (Pb, Pr) and the
luminance (Y) signal will improve color bandwidth information.
Connect the Component (Y, Pb, Pr) Video OUT jacks
from the DVD player (or similar device) to the (Y, Pb, Pr)
AV4 IN(put) jacks on the TV.
Connect the red and white AUDIO CABLES to the
AUDIO (left and right) OUT(put) jacks on the rear of the
accessory device to the Audio (L and R) AV4 IN(put) jacks
on the TV.
3
4
Pre_ the AV button on the remote control repeatedly to
tune to the AV4 channel.
Turn the TV and the DVD (or digital accessory device)
ON.
Press the PLAY button on the DVD (or digital accessory
device) to view the program on the television.
NOTE: This television is designed to accept high definition sig-
nals i080i and 480p as specified by the Electronic Industries
Association standard EIA770.3. Digital devices from different
manufacturers have the possibility of differing output standards
which my cause difficulties for the television to properly dis-
play.
Note: If the AV4 chain]el is tuned and no signal con-
nection present, the screen could jmnp or flash.
AV4
®®®
®
JACK PANEL
ONBACKOFTV
VIDEO 2Fh
r5_ 480p/1080J
MONITOR
vOUT,
VIDEO
oo,:®
COMPONENT
VIDEO
CABLES
OUT OUT
l
JACK PANEL
OF DIGITAL DEVICE SUCH
AS A DVD PLAYER
EQUIPPED WITH
COMPONENT VIDEO
OUTPUTS
E0
J
AUDIO IN
(RED/WHITE)
This television has input jacks corn eniently located on the side
J[ of the cabinet. These jack are Jbr easy hook-ups (without hav-
ing to move around to the back of the TV)Jbr cameras, gaming
units, and other accessory devices that wouldn't be connected
permanently. Folh)w the ea_v steps below to connect your acces-
sory device to the SIDE Input ,lacks h)cated on the right side of
the T_
[
2
3
4
Connect the VIDEO (yellow) cable to the VIDEO IN
jack on the side of the TV,
Connect the AUDIO (red and white) cables to the
AUDIO (left and right) IN jacks on the side of the TV.
Connect the VIDEO (yellow) cable to the VIDEO OUT
jack on the back of the camera (or accessory device).
Connect the AUDIO (red and white) cables to the
AUDIO (left and right) OUT jacks on the rear of the cam-
era (or accessory device).
Turn the camera (or accessory device) and the TV ON.
Press the AV button on the remote control repeatedly to
tune to the AV3 channel.
With the camera (or accessory device) ON and a prere-
corded tape (or other media depending on type of accesso-
ry device being used) inserted, press the PLAY button to
view the tape on the television.
NOTE: The S-Video Cable can be used in place of the Yellow
Video cable shown in this diagram. If your camera or accessory
device has a S-Video output jack, connecting the video signal
through the S-Video jack will reproduce the video signal with
greater quality.
AV3
PIP04 (:O',rr_. mm_e
0¢¢0
dO®®
VIDEO IN
(YELLOW) AUDIO IN
(RED &
WHITE)
Jack Panel of
C_l]]era
or Exlemal
Accessory Device
S-VIDEO VIDEO LEFTADDR[ODHT
SIDE (AV 3) II]pul Jacks
Located on the Side of
the Televisiot] Cabinet
S-VIDEO
VIDEO
AUDIO
The SIDE
JACKS alst3
contain a
HEADPHONE
JACK.
6