Philips 30PW862H Directions For Use Manual page 74

To load the supplied batteries into the remote:
Remove the battery compartment door on the back of the
remote.
Place the batteries (2-AA) in the remote. Be sure the (+) and
(-) ends of the batteKtesline up correctly (the inside of the case
is marked).
Reattach the battery compartment door.
Be sure to point the remote at the Remole Sensor window on
the front of the television when using the remote control to
operate the television.
Remote Control
(shown fi'om the bottom)
2 "AA" Batteries
- Battery Compartment
\ Battm T Companment Door
VCR control buttons
- Press to pause, rewind,
stop, play, or fast forward a videotape.
TV • VCR • ACC - (Mode buttons) Press to send --_
remote signals to either ihe TV, VCRs, or other accessory
\
devices such as cable TV converters, satellite receivers,
DVDs, or laser disc players. (You may need to program
the remote to work accessory devices. Refer the Directions
/br Use manual.
PIP buttons: SWAP, PIP CH DN/UP,
FREEZE
- Press to operate the Picture-in-Picture (PIP)
features.
Sound
- Press to select an AutoSound
TM
control. Choose
from three factory-set controls--Voice, Music, and
Theatre--and a Personal control that you set according to
your own preferences through the onscreen Sound menu.
The three factory-set controls will tailor the TV sound so
as to enhance the type of program you are watching.
Status/Exit
- Pressing the button once shows the cur-
rent channel number, name (if set), time (if set), Sleep
Timer setting, and sound setting (stereo, mono, SAR or
mute). Pressing the button twice shows the current
AutoLock
TM
settings. Pressing the button once when an
onscreen display is showing removes the onscreen display.
Cursor Ring - Up_own:
allows you to select the next
or previous menu item in ihe menu. Left/Right: allows you
to access the submenus and adjust the settings. When no
onscreen displays or mends are present, use the Cursor
Ring Left/Right to select a picture format for a video
source connected to the ANTENNA, AVI, CVI, AV2, or
AV3 (side panel inputs) on tile TV.
Volume (+/-)
- Press to adjust the TV sound level.
Number Buttons
- Press to select TV channels.
When selecting single-digit channels, press the number of
the desired channel. The TV will pause for a few seconds
and tllen tune to the selected channel.
TV/VCR - Press while in VCR mode to view the play-
back of a videotape. Press again to return to TV mode./
_dCH - When in the TV mode, press to alternate
between the currently viewed channel and 1he previously
viewed channel.
Rec •
- Press tilts button simultaneously with tile _-
button when in VCR mode to record.
SAP
- When in tile TV mode, press to select between
main sound and SAP (Second Audio Program) when you
tune to a program offering SAR
AV - Press repeatedly to select the different signal source
connected to the TV: TV (current channel), AVI, CVI,
AV2, AV3 (side jack panel), AV4 and AV5.
Clock
- Press to access the onscreen Timer menu, where
you can set the time for the TV's clock or set the TV's
Timer features, such as channel switch over, power on set,
and power off set.
Position
- Press to move file PIP picture to any of the
four comers of the screen.
®
®®
TWVCR
REC ii CC
AV DOLBY V PROG
PIP
)
S Power - Press to turn tile TV on or off.
Active ControITM
.
Measures and corrects all
F incoming signals to provide the best picture-quality
/ settings. Press to turn Active Control
TM
on or off.
/ When Active Control
TM
is on, it automatically and
[ con!inuously controls Sharpness and Noise Reduction
settmgs,
Picture - Press to select an AutoPicture
TM
control.
Choose from four factory-set controls--Movies,
Sports, Weak Signal, and Multimedia--and a PER-
SONAL control that you set according to your own
preferences through the onscreen Picture menu.
_ enu/Select
- Press to display the onscreen
menu. Press to return to a higher menu level.
Channel (+1-)
- Press to select channels in
_21npguO: descending orderor cyclethroughthe
Mute - Press to turn the TV sound off. To restore the
sound to its previous level, press the button again.
/ /-- Surf- Press to select previously entered channels.
/ [ With the TV's AutoSurf
TM
control, you can place up
/ to i0 favorite channels or sources in memory. Then by
[ pressing the Surf button, you can quickly view the
selected channels.
/ CC Button - Press to select Closed Captioning
options wifllin tile menu.
} - Press to set the TV to automatically turn
itself off after a period of time. Choose 15, 30, 45, 60,
90, 120, 180, or 240 minutes before llae TV will auto-
matically turn off.
Program List
- Press to display a list of channel
numbers and their names. Each channel will appear as
a selectable menu item. The current channel will be
highlighted as default. Five channels will be listed on
screen a_ one time. Press the Cursor Ring up or down
to scroll lhe list and and highlight a channel. Press the
Cursor Ring right to tune to the highlighted channel.
Channels marked "Skipped" in lhe Channel Edit con-
trol will not appear in the list. Each channel that is
being blocked by AutoLock
TM
will appear with a pad-
lock icon to indicate that fide channel is not viewable.
DolbyV
- Press to select various factory surround
sound listening modes.
Dolby*Virtual (Virtual Dolby Surround)
(with Virtual Dolby Surround signals) - Dolby
Virtual uses two speakers to simulate lhe surround
effect produced by a multichannel system.
Incredible Surround
TM
* In Stereo sound
mode--when Incredible Surround
TM
is turned on--
it seems as though the loudspeakers are spread far-
tiler apart from each another. In Mono sound
mode--when Incredible Surround
TM
is turned on--
enables you to hear a spalial sound effect.
PIP
- Press to turn PIP (picture-in-picture) on or off
or control llae size of the PIP window.
Back Light button
- Press to light the buttons
on the remote control.
2