Philips 51PW9363 Directions For Use Manual page 77

Tahe AUTO PROGRAM.fbature will scan jbr channels with ,
clive broadcast signals and store those channels in the TV s
memorw It will tune up to 69 channels' [br antenna, and up to 125
ehannels.ibr cable. After you run AUTO PROGRAM, you can use
the CH(annel) +/- buttons to quickly and easily select stations.
You can also press the PROG. LIST (Program Lis 0 button on
your remote to see a list of the channels'.
2
3
4
Press the MENU/SELECT button. The on-screen menu
appears. Then press the CURSOR RING DOWN repeated-
ly until INSTALL is highlighted.
Press the CURSOR RING RIGHT to enter the INSTALL
submenu. Then press the CURSOR RING DOWN repeated-
ly until AUTO PROGRAM is highlighted.
Press the CURSOR RING RIGHT to begin the automatic
search for channels. The progress of autoprogramming is
displayed+
When the programming is done, press the STATUS EXIT
button to exit the menu.
• AutoChron
• T
• AUTOPROGRAH
• CHANNELEDIT
• Au_oChron
After you've run AUTO
PROGRAM, check the
results. Press the
CH(annel) bi buttons on
iour remote to cycle
through your available
channels. Or press the
PROG. LIST button to
show a list of the channels
and tune to them. See
page 28 in the Directions'
[br Use manual for more
"on Program List.
Philips strongly recom-
mends that you run Auto
Program. Otherwise, the
TV may not tune the chan-
nels properly, resulting in
improper pictures.
If you change signal
sources to a new cable
company or from antenna
to cable, for example be
sure that Tuner Mode is
properly set for the new
source. Then run Auto
Program again. This will
ensure that the channels
are correctly stored in the
TV's memory.
If you have made
AutoLock
TM
settings,
remember that you must
remove any channel blocks
before Auto Program will
work. (See pages 44_52 in
the Directions [br Use
manual.)
T_itsiS feature allows you to edit or st@ channels' [kern the channel
t )hat have bad or weak signals or channels' you do not want
to watch.
2
3
4
Press the MENU/SELECT button. The on-_reen menu
appears. Then press the CURSOR RING DOWN repeatedly
until INSTALL is highlighted. Press the CURSOR RING
right to enter the INSTALL submenu.
Press the CURSOR RING DOWN repeatedly until
CHANNEL EDIT is highlighted. Then press the CURSOR
RING RIGHT or LEFT to access the CHANNEL EDIT list.
Press the CURSOR RING UP or DOWN to _roll
through the list of channels. Or press the NUMBER buttons
on your remote control to select a specific channel.
With the channel you want to edit selected, press the
CURSOR RING RIGHT to mark the channel as
SKIPPED. (Channels you mark SKIPPED will not appear
when you use the CH[annel] +/- buttons to change channels
while watching TV.)
When you want to add a channel that has been marked
SKIPPED, press the CURSOR RING UP or DOWN to high-
light the channel. Then press the CURSOR RING RIGHT to
remove the word SKIPPED.
Press the STATUS/EXIT button to exit the menu.
[ftSTALL
• LAHGIIAGE AU3
• TUNE_, ItOOE AY4
• AHTO PHOGRAM I
• AutoChron 3
, i
®
i i! ilill
• AUTO PEOGRAH
• CHAEHELEDIT
• AutoCilron
Channels that Auto
Program (,see page 5)
determined not to contain
active broadcast signals are
marked SKIPPED.
TM ;
z_ utoChron gi_ es you the option q['setting the time manually or
l automatieally.
SETTING TIME AUTOMATICALLY
The steps in this section tell you how to set AutoChron TMto
download the time.[kern your PBS station to your T_ Aider suc-
cess/hi setup, AutoChron T_ will automatically maintain the cor-
rect time using your PBS station until you set the time manually.
2
Press the MENU/SELECT button. The on-screen menu
appears. Then press the CURSOR RING DOWN repeatedly
until INSTALL is highlighted.
Press the CURSOR RING RIGHT to enter the INSTALL
submenu. Then press the CURSOR RING DOWN repeated-
ly until AutoChron is highlighted.
Press the CURSOR RING RIGHT to enter the
AutoChron SET TIME area.
Press the CURSOR RING RIGHT again to select AUTO.
Within a few seconds, a menu containing the time-zone
options appears.
If necessary, press the C URSOR RING UP or DOWN to
highlight your correct time zone. Then press the CURSOR
RING RIGHT. Within a few seconds, the option of Daylight
Savings Time appears on screen.
If the Daylight Savings Time option you want to select is
not highlighted, press the CURSOR RING UP or DOWN
to highlight the option. Then press the CURSOR RING
RIGHT to activate your selection.
Press the number buttons on your remote to enter the
channel number fur your PBS station (02, 15, or 121, for
example). Wait until the TV completes its search. If the time
was not found, you will need to locate the correct channel
number for your PBS station and input that number.
Press the STATUS/EXIT button to exit the menu.
INSTALL
• _GUAGR "
• TUHER MOOE sETTmR
• AUTO PROG_H
• C_ANHEL HOlT
o_ AUTO
•
MANUAL
®@
@
PHILIPS
INSTALL
• LANGUAGE
• TONER HOOE
• AUTO PHOGRAH
• CHAHNELEDIT
< AutoChron
IHSTALL
• L_HGUAGE
• TUItEH MO_E
• AUTOPROGP&tl
• CHANNELEOiT
_I Au_oChron
IHSTALL
,LANGUAGE
• TUNER HODE
• AUTO PHOGRAH
• CHAHNELEOIT
4 AutoRh_on
The message shown to
the right indicates that
AutoChPon
TM
is not
finding a PBS station at
the channel you input.
Check the channel
number for your PBS
station.You will need to
input the correct num-
ber for the time to be
found.
INSTALL
• LAHGUAGE
• TUNERHODE
• AUTOPROGRAM
• CItAN_EL EDiT
_I AutoEhron
INgTALL
• LAHGUAGE
• TUHERHODE
• AUTOPROGRAM
• CHAN_ELEDIT
< AutoEhron
IISIALL
• LANGUAGE
• TONER _ODE
• AUTO PROGi_AH
• CHAEHELEDIT
_1 Auto'run
INSTALL
• LAEGUAGE
,TUHERMOOE
• AUTOPEOGRAN
• CHANNELEOIT
• Au_oChron