Table of Contents
Advertisement
25
Timer Recording
With VCR Plus-' ....
Remote Control
POWER
Button
Number-
Buttons
O
C:::D
00000
O0
O0
-VCR
PLUS+/
ENTER
Button
-MENU
Button
Button
after you enter the VCR Plus+ number,
the number you entered was incorrect
(for example, too short). If this hap-
pens, press the CLEAR button to clear
the number, then enter the correct
number.
• CLASH m_y flash on the screen at step
.
2. This means that the timer recording
you just programmed and another
timer recording overlap, and thus the
i
current timer recording will not be
carried out.
• To quit VCR Plus+ programming at
any step, press the MENU button. The
on-screen display will disappear from
the TV screen.
• If the preset time for a timer recording
comes up during an OTR, the OTR has
"
priority.
• To stop a started timer recording, press
the STOP/EJECT button on the VCR.
• If the power fails for more than one
minute, programmed timer recordings
may be lost. If this case, repeat the
steps on pages seven and ten before re-
programming the timer recordings.
See page 35for more notes.
o
Read steps 1-7 to program a timer
recording using VCR Plus+ numbers.
Before you begin make sure:
• Channels have been programmed.
• The clock has been set.
• There is a tape in the VCR (make
sure the tape's record tab is intact
and the tape is long enough to record
the program(s).
• The VCR is in VCR position.
• You have selected CABLE TV or
TV at the TUNER SET UP menu.
You must do each step within 60 sec-
onds of completing the previous step.
If you don't, you will have to start
again at step 1.
Press the VCR PLUS+/ENTER button
on the remote control. The on-screen
display shown below will appear.
"5
Lus
.... -J
END PUSH MENU
J
2
Press the Number buttons for the VCR
Plus+ number of the program you wish
to record (this number is different for
every program, and it can be four to
eight digits long). Finally, press the
VCR PLUS+/ENTER button.
_us _O_E:,_-
TO SET PUSHVCR +
• TO CORREC3"PUSH CLEAR
X,,T, 0 ENDPUSH MENU
3
•
To record the program once, press the
Number 1 button to select ONCE. To
record the same program every day from
Monday through Friday, press the
Number 2 button to select DAILY. To
record the same program every week on
the same day (such as every Saturday),
press the Number 3 button to select
"_'1:7_R'I x/
4
Press the Number 1 button to record in
SP speed, press the Number 2 button to
record in LP speed, or press the
Number 3 button to record in SLP
speed. For details, see page five, You
cannot use the (Tape) SPEED button at
this time.
Pd0d
;
El.
9
0N
10_0 Rd
MEOFF
11:30 PM
C:_E_E_
I 8LR _/_
PUSH MENU "
5
Press the MENU button. PROGRAM
WAS COMPLETED / PLEASE TURN
OFF VCR FOR TIMER RECORDING
should appear on the screen. After
three seconds, the on-screen display
_
will disappear.
6
If needed, press the VCR PLUS+/ENTER
button and repeat steps 2 to 5. When you
are finished, go to step 7.
7
Turn off the VCR power. The Timer
light will appear. The VCR must be
turned off for a timer recording to
take place. If you forget to turn the
VCR off, PLEASE TURN OFF VCR
FOR TlMER RECORDING flashes
on your TV screen two minutes before
a timer recording starts. You can
remove it by pressing the CLEAR but-
ton.
The VCR
l
must be off for a
timer recording
to take place!
I
I
I
Advertisement
Table of Contents
