Table of Contents
Advertisement
(1) Slide TV-CATVswitch
to CATV.
(2) Press and hold down INPUT STATUS and
CH DOWN (Y) on your remote control.
Then release both buttons.
(3) Within
ten seconds
after releasing
INPUT
STATUS
and CH DOWN
(V),
enter
your
converter's
two-digit
code
number
using
REMOTE KEYPAD (refer to list).
• The remote
control
is now ready
to send
commands to your converter.
• Some brands have more than one remote code
listed due to changes in the remote codes from
early to later model years. In such cases, you
may have to try more than one code to find the
code your converter accepts.
NOTE:
Depending on the model, year produced, brand,
and type of CATV converter, some models may
not be compatible with the remote control.
•
To Identify Your Cable Converter-
Search
Method.
(1) Slide TV-CATVswitch on the remote to CATV.
(2) Press
the POWER
button
on the cable
converter to ON.
(3) Stand at least six feet away from the converter.
Point the remote towards the converter.
Hold down the INPUT STATUS and CH UP (_t )
at
the same time.
KEEP HOLDING
THE
BUTTONS
DOWN.
(4) Watch the Channel Number indicator on the
converter.
Channel
numbers
will scan up when
the
converter has been identified.
Release the INPUT STATUS and CH UP (_t)
as soon as the channel numbers start to scan
up.
The converter's
remote control code number
has been identified, and the remote is ready to
operate the converter.
TIPS
ON
IDENTIFYING
YOUR
CABLE
CONVERTER:
Be Patient: a minute or two can seem a lot
longer when you're waiting for something
to
happen,
but the code should
be identified
within two minutes.
Remember,
it is only a
one-time set-up.
Be careful not to let the CATV converter scan
more than five channels
when the indicator
starts to move up. If you continue hoiding down
the INPUT STATUS and CH UP (,)
after five
channel scans, the proper remote code can be
passed up, and the two minute
identify cycle
will have 1o be repeated.
if a channel change does not occur on the cable
converter
within
two
minutes,
read
the
identifying
instructions
again and repeat the
steps. Should a channel change still not occur,
the remote will not operate with the desired
converter.
CATV CONVERTER
REMOTE CONTROL
BRAND
CODE NUMBER
Anvision
..................................................
07, 08
Cable Star ..................................
07, 08
Eagle
................................... 08
Eastern International
...... 02
General Instrument
........... 04, 05, 15, 23, 24, 25,
30, 36
Hamtin
.................................. 12, 13, 34
Jerrold .............................................
04, 05, 15, 23_ 24, 25,
30, 36
Macom
.................................... 3 7
Magnavox
..................................
07, 08, 19, 25, 28, 29,
32, 33, 40, 41
NSC ........................................09
Oak ..........................................................
01, 16, 38
Oak Sigma
............................18
Panasonic ..................................
27, 39
Philips ..................................................
07, 08, 19, 26, 28, 29,
32, 33, 40, 41
Philips Magnavox
................. 0 7, 08, 19, 25, 26, 28,
29, 32, 33, 40_ 4t
Pioneer ....................................... 18, 20
Randtek
.............................. 07, 08
RCA ..................................................
27, 43
Regal
................................... 12, 13
Regency
............................................
02
Scientific Atlanta ................. 03, 22, 42
Sony ......................................... 44
Sylvania
.............................. 11
Teknika .................................. 06
Texscan
.............................
11
Tocom .................................. 17, 21
Unika
................................... 31
Viewstar
.............................. 07, 08, 19, 26, 28, 29,
32, 33_ 40, 41
Zenith
.................................. 14
NOTE:
Some satellite receivers can be operated by the
REMOTE CONTROL.
If you have a Satellite
Receiver,
you can use the above method
to
search for available channels.
HELPFUL HINT:
Write down the compatible code for your cable
box and/or your VCR somewhere
other than the
owner's manual (for instance, inside the battery
door), to prevent problems that may occur if the
owner's manual is misplaced.
Each time the
batteries are replaced, you will need to reset the
remote to work with your cable box and/or your
VCR.
39
Advertisement
Table of Contents
