Advertisement
Install Ignitor Batteries
[]
Unscrew
ignitor
Caps
from
Control
Panel.
[]
Place
one
supplied
AA
battery
into
each
Ignitor
Slot
with
positive
pole
facing
you.
[]
Position
the
Cap
and
Spring
over
the AA
battery
in each
ignitor
Slot
and
tighten
to
Control
Panel.
Main Burners Electrode
Check
Perform this Electrode
Check with the
assistance
of another person.
This test will ensure
that the Spark
Electrode
Tips
are properly
positioned
so your
grill lights
easily
and properly.
Spark Gap
Gas Collector
Box
inside Nut
Spark Receiver
[]
[]
[]
[]
Spark Electrode Tip
Be
sure
all Control
Knobs
are
set
to
"OFF"
and
open
the
Grill
Lid.
Have
your
assistant
stand
behind
to the
right
of the
grill and
look
toward
the
front
of the grill
bowl.
Never
put your
face
inside
the
Grill
Bowl.
Turn any Control
Knob of Main Burners
to IGN
and push
in and have
assistant
watch
for a
blue spark
within
each
Gas Collector
Box.
If no spark
is seen,
the
Spark
Gap
needs
to be adjusted
as follows:
•
Using
an adjustable
wrench,
loosen
the
Inside Nut until the Gas Collector
Box can
be turned
upward.
•
If the gap
between
the Spark
Elec-
trode
Tip
and
Receiver
is more
than
3/16"
use
long
nose
pliers
to gently
squeeze
the
Gas
Collector
Box to
narrow
gap.
•
Return
the Gas Collector
Box to its
original
position,
secure
the Inside
Nut
and try the Electrode
Check
again.
If no
"clicking"
sound
is heard:
•
AA Battery may be installed
backwards.
•
Electric
wires
may be loose.
Remove
the AA Battery and inspect the Ignitor
Junction
Box found
behind the Control
Panel and reconnect
any loose wires.
H
ide
Burner
and
Back
Burner
Electrode
Check
[]
Open
side
burner
lid.
Remove
plastic
shipping
band
from
burner
and
pot
support.
[]
Turn
side
burner
Control
Knob
to IGN
and
push
in.
Look
for
spark
between
tip
of electrode
and
burner.
[]
Open
Grill
Lid. Turn
back
burner
Control
Knob
to IGN
and
push
in. Look
for
spark
between
tip of electrode
and
burner.
[]
If you don't
see a spark
from
side
or back
burner
electrode,
adjust
gap between
electrode
and burner
surface
to 3/16
in.
AA Battery
pring
Ignitor Cap
Ignitor Slot
Install
Cooking Components
[]
Place
the
Savor
Plates
TM
on
lower
ledge
above
Burners.
[]
Place
Cooking
Grids
on
bowl
ledge.
[]
Place
the Secondary
Cooking
Rack
into
the
slots
on Grill
Bowl
Side
Panels.
[]
Place
the
Side
Burner
Pot
Support
on
Side
Burner
Body.
Secondary
Cooking Rack
Cooking Grids
Savor PIatesTM
Slots for
Secondary
Cooking Rack
Model 141.16682/17682
. Q
Side Burner
Pot Support
Model141.16684/17684
10
When you have finished
assembling
your
grill be sure that all screws
are tightened
for safe operation
of your grill.
Advertisement
