Related Manuals for Philips 22HFL4373D/10
Summary of Contents for Philips 22HFL4373D/10
- Page 1 Philips Hospitality TV Installation Manual for 22HFL4373D/10 26HFL4373D/10 32HFL4373D/10 42HFL4373D/10 Version 1.0...
-
Page 2: Table Of Contents
Contents Requirements before starting the installation ......................2 Find out the state of the TV ............................3 Re-install TV ................................4 Installation wizard ..............................6 Channel options ..............................13 Reordering channels ............................13 Rename channels ..............................15 Hide channels ..............................15 PBS Mode ................................ -
Page 3: Requirements Before Starting The Installation
Guest Remote by pressing 1,2,3,6,5,4. Go to: http://www.support.philips.com/support Enter the model number and check to confirm you have the latest version available. Confirm the software version present on TV is identical with the one from website. If not please download the latest version from website, unzip and save on to a USB key The USB key must be format FAT32 and preferably empty to avoid and accidental upload of wrong setting and software. -
Page 4: Find Out The State Of The Tv
2. Find out the state of the TV It is important to know if a TV is in ‘virgin mode’ (out of the box) or installed before. If you can see this screen below, you know that the TV is in ‘virgin mode’ and you can install the set. See chapter 4 of this manual. -
Page 5: Re-Install Tv
3. Re-install TV If you want to start an installation from scratch you can always re-install the TV. This can be done by using the option: Re-install TV set. If PBS is active you can access the setup menu press the ‘RC5 SETUP’ key, and then press the ‘Home/Menu’ button (For the guest remote control, press the following keys in sequence: 3,1,9,7,5,3, ‘MUTE’) , then go to TV Setup, confirm with “OK”. - Page 6 Press “OK” to access the sub-menu, navigate to “Reinstall TV”. Press “OK” to reinstall the TV set. If all is correct select “YES” and press “OK”. After this operation the TV will power off and on and display the installation wizard. Note: All settings are at default values and no channel plan is available.
-
Page 7: Installation Wizard
4. Installation wizard When you turn on the TV for the first time, or you have reinstalled the TV, you should see the following screen. Here you will need to select your preferred language. After this, you will need to select the country. Depending on the country selection, some pre-defined settings will be activated, because of local broadcast requirements. - Page 8 The next step is to select ‘Wall mounted’ or ‘On a TV stand’. This option changes some settings for the audio and image of the TV. The next step is to choose between ‘Shop’ and Home’ use. If you select “SHOP” an ‘e-sticker’ banner will be displayed on the TV.
- Page 9 For the channel installations, select ‘Install TV channels’ and press ‘OK’ Then you can select ‘Continue’ and press ‘OK’ again. Here you can select the type of channels you would like to install and what preference you will use.
- Page 10 It is advisable to check the settings before starting the search. Note:If all options are disabled you have to go down to the Digital channels option and set the digital channels to ON. A screen is displayed to make changes to set the channel list/map configuration: [Symbol rate mode]: Automatic: the TV will use the preset Symbol rate (6.900/6.875) Manual: Option to set Symbol rate 1 and Symbol rate 2...
- Page 11 Frequency step size has two options: 1. “1 MHz” – With Full scan, the step size to search for channels is 1 MHz The scan will take more time but will find also channels broadcasted not according to the channel grid. 2.
- Page 12 During the channel search you can see the progress bar and how many channels are found at that time. When the search is done, you should see “Channel search complete” and a summary of the channels found. In this case: Digital channels found: 53 Analogue channels found: 0 Press the “OK”...
- Page 13 The wizard will ask you some questions about which image you prefer, select the option you desire and press “OK” on the remote control. Once this wizard is done, you will return to the installation menu again. The last option in this menu is “Add your devices”.
-
Page 14: Channel Options
5. Channel options a. Reordering channels For reordering TV channels the channel plan from PBS Setup must be used. In consumer menu you cannot rearrange channels. The PBS Setup can be accessed by using the Yellow remote (RC 22AV8573 Master Remote control) and pressing the MENU Button or with the TV remote press 3,1,9,7,5,3, MUTE). - Page 15 Navigate to the channel that you want to move and press “OK” on the remote control to select that channel. The arrows around the channel indicate that the channel is selected and can be moved. Use the arrow keys to move the channel to the new position.
-
Page 16: Rename Channels
Press “OK” on the remote control to confirm that you are done with the re-ordering. b. Rename channels Select the channel, press the “Options” button on the remote control and select “Rename” to change name of a channel. If you then press the “OK” button a virtual QWERTY keyboard will pop up. c. -
Page 17: Pbs Mode
6. PBS Mode Select the Setup menu language to be English, French, German or Italian. [Off]: The TV operates as a basic (consumer) TV. [On]: All settings in the PBS mode Setup menu are active. Only by switching on this mode the TV will act as a Hospitality TV. - Page 18 [On] To enable the welcome message. [Off] No welcome message Line 1: First line of the welcome message. Line 2: Second line of the welcome message. Clear: Will delete the message entered on the welcome message. A virtual keyboard will pop up when pressing the “OK” button on the remote control while editing line 1 or 2.
- Page 19 [Off]: PBS setup menu can be accessed by both Guest remote control and Master remote control 22AV8573 (yellow) or RC2573 (green). Guest remote control access to the set up menu only possible with code 3,1,9,7,5,3, mute. [On]: PBS setup menu can only be accessed by the Master remote control 22AV8573 (yellow) or RC2573 (green).
- Page 20 Allows menu to control external HDMI-CEC. [Off]: Disables TV functionality to control external HDMI-CEC devices. [On]: Enables TV functionality to control external HDMI-CEC devices. Enables or disables USB break-in feature in Professional mode: [Off]: When USB device is plugged in, the [Multimedia] menu will not appear automatically, but users can access [Multimedia] menu from the Guest menu.
- Page 21 Enables or disables the use of EPG OSD on pressing EPG button: [Off]: No EPG services available [Now & Next]: EPG (Now/Next) services available [8 Day EPG]: EPG (8 Day) services available Note: EPG availability depends on local conditions. Enables or disables the use of subtitles at start-up: [Off]: No subtitles services available [On]: Subtitles services available [On during mute]: Subtitles services when TV audio is muted...
- Page 22 The Low power standby option defines the TV to enter a specific standby mode after pressing the On/Off button on the remote control. [Fast]: The TV will quickly turn on (This mode will consume more power in stand-by, compared to Green mode). [Green]: The TV will turn on less fast.
- Page 23 Defines the brightness level for the Clock LCD backlight if the TV is in On mode: [Set]: Off, 1, 2, 3, 4, 5 Select the source for the clock time: [Automatic]: Clock time is retrieved from the “Download Program” channel. [Manual]: The clock time is set using the Time Setting option.
- Page 24 Audio Clock Time Alarm (buzzer): [Set]: Off, On Set the Daylight saving options: [Set]: Off, On Check [Feature settings] (on page …) [Off]: The main speakers are muted. The RC can control the volume and mute the headphone/bathroom speaker [On]: The main speakers are active and the behavior of the headphone/bathroom speaker is defined by the Independent Main Speaker Mute.
- Page 25 Restore the factory default of the PBS Menu. Channel installation is not affected. A shortcut to enter the consumer installation menu. Consumer installation menu should be accessed to change e.g. picture and sound settings and update channels. Using this shortcut will trigger a popup screen which warns loosing settings in the PBS menu if you continue.
- Page 26 Only applicable for system connected installation. After storing PBS settings, the TV will restart to apply the new parameters. Now you can clone all settings to other TV sets by using the option TV to USB and USB to TV. Check how to clone settings (on page 28).
-
Page 27: Welcome Logo
7. Welcome Logo There are 2 Philips logos displayed at startup. The second logo can be replaced by a picture uploaded via USB. File format: 960 x 540 .jpg file. The Welcome Logo is displayed only when Standby mode is set to “Green”. -
Page 28: Smart Clone
8. Smart Clone Smart Clone With Smart Clone it is possible to copy to/from a USB device TV the configuration data and channel list data. Place a USB Memory stick in the USB side connector of the TV. *The USB device should be formatted as FAT or FAT32. [USB to TV] 1. -
Page 29: Feature Settings
[Startup]: ThemeTV is show at startup, but the function can be trigger by pressing the ThemeTV button on the RC. [VSecure] VSecure is the hospitality content scrambling method used by the Philips Hospitality TVs. If you are interested to use it please contact the local Philips Hospitality TV sales representative. -
Page 30: Rf Download
Instead of using a USB memory device to do cloning and firmware update, this upgrading is also possible using the RF infrastructure. This is supported by SmartInstall (Philips Hospitality RF Download mechanism) and allows a simultaneous upgrade of all installed televisions.