Frigidaire PL36WC50EC Professional series Use & Care Manual
Professional series
Hide thumbs
Also See for PL36WC50EC Professional series:
- Instruction manual (13 pages) ,
- User manual (25 pages)
Related Manuals for Frigidaire PL36WC50EC Professional series
Summary of Contents for Frigidaire PL36WC50EC Professional series
- Page 1 PROFESSIONAL SERIES Model PL36WC50EC ENGLISH ........3 FRAN(_AmS........ 12 99043841 A...
- Page 2 INTENDED FOR DOMESTIC COOKING ONLY _, WARNING TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR iNJURY TO PERSONS, OBSERVE THE FOLLOWING: 1. Use this unit only in the manner intended by the manufacturer. If you have questions, contact the manufacturer at the address or telephone number listed in the warranty.
-
Page 3: Operation
OPERATION BLOWER Controls LIGHT PILOT MEDIUM SWITCH LAMP SPEED The hood is operated using the (4) push-buttons located at eye-level, on the front edge of the hood. BLOWER BLOWER ON-LOW The light switch turns the halogen lamps on and off. HIGH SPEED SWITCH... -
Page 4: Prepare The Hood
PREPARE THE HOOD Unpack hood and check contents. You should receive: 1 - Hood 1 - Decorative Flue Assembly 1 - Parts Bag containing: 1 - Mounting Bracket DISCHARGE MOUNTING COLLAR 1 - Discharge Collar BRACKET 1 - Flue Mounting Bracket 8 - Mounting Screws (4.8 x 38mm Pan Head) 4 - Mounting Screws (3.9 x 9.5mm Pan Head) 2 - Mounting Screws (3.9 x 6ram Flat Head) -
Page 5: Install The Ductwork
iNSTALL THE DUCTWORK (DUCTED HOODS ONL Y) ROOF CAP CAUTION: To reduce the risk of fire, use only metal ductwork. 1. Decide where the ductwork will run between the hood and the outside. 2. A straight, short duct run will allow the hood to perform most efficiently. 3. - Page 6 INSTALL FLUE MOUNTING BRACKET (DUCTED AND NON-DUCTED HOODS) 1. Assemble the flue mounting bracket, adjusting outside width as shown. See Figure 7. 2. Carefully center the mounting bracket directly over the range hood location. 3. Secure the bracket assembly to the ceiling using (2) 4.8x38mm mounting screws and drywall anchors (Fig. 8). Make sure the bracket is pushed into the corner, tight against the wall and centered over the hood.
- Page 7 PREPARE THE HOOD (NON - DUCTED HOODS ONLY) Note: The following materials must be purchased separately for non-ducted recirculation installations. o Non - Ducted Recirculation Kit, Model DFKTWC50EC. o 5" diameter metal duct. 1. Discard discharge collar supplied with the hood. Install the 5" to 6" adapter supplied with the Non-Ducted Recirculation Kit.
- Page 8 MAKE ELECTRICAL CONNECTIONS WARNmNG: Electrical wiring must be done by a qualified person(s) in accor- WIRING BOX dance with all applicable codes and standards. This range hood must be COVER properly grounded. Turn off electrical power at service entrance before wir- ing.
- Page 9 iNSTALL FILTERS (DUCTED AND NON-DUCTED HOODS) 1. To remove the GREASE filter, push in on the metal latch tab and tilt filter downward to remove. 2. To install the GREASE filter, align rear filter tabs with slots in the hood. Depress the metal latch tab, push filter into position and release.
- Page 10 Your appliance is covered by a one year limited warranty. For one year from your original date of purchase, Electrotux wilt pay all costs for repairing or replacing any parts of this appliance that prove to be defective in materials or workmanship when such appliance is installed,...
- Page 11 SERVICE PARTS- LISTE PIECES DE RECHANGE MODELS PL36WCSOEC KEY No. DESCRiPTiON (ENGLISH) DESCRiPTiON (FRANCAIS) Grease Filter FiItre b, graisse Condensateur Motor Capacitor Wiring Plate Plaque du systeme electrique Lamp Bulb Ampoule Blower Convoyer Motor Moteur Blower Wheel Turbine Rubber Washer Pare chocs Blower Mounting Cover Support moteur...
-
Page 12: Pieces De Rechange
SERVICE PARTS - USTE PIECES DE RECHANGE MODEL PL36WCSOEC ....& - _PPPP __-_ ..