Turning On The Power; Savingthe Powerconsumption While On Standby; Selectingthe Sourcesand Startingplay - JVC NX-CDR7 Instructions Manual

Continued I_
Before operating the unit any further, first set the clock
built in this unit (see page 45).
Turning On the Power
To turn on the unit without playing, press 0/I so that the
STANDBY lamp on the unit goes off, and the CDR lamps
light.
, , , = = , ,
! ! !.... L_ L... =... =
To turn offthe unit (on standby), press 0/I again so that
the STANDBY lamp lights red, and the CDR lamps go off.
="" F" ".... : : .'. : : J
.:::,1:::. i :::. "!" LJ U
• When the power is off (on standby), clock time appears
in the main display--initial setting when shipped from
the factory (see "Saving the Power Consumption while
On Standby" below).
• A little power is always consumed even while the unit is
in standby mode.
To switch off the power supply completely, unplug the
AC power cord from the AC outlet.
Savingthe PowerConsumption while On
Standby
You can save the power consumption while the unit is
turned off by erasing the clock display.
To save the power consumption while on standby, press
DISPLAY on the remote control while the unit is turned off
(on standby--while the STANDBY lamp lights red).
1'","1' ,:::' 1:::, [ !:::! ".J ¢"=1:::" i :::"
1... .1..... • = 1.... , , = ..... = ,
• Power consumption during standby is reduced (see
"Specifications" on page 54) and the clock will not be
shown while the unit is turned off (on standby).
To cancel the power consumption saving mode, press
DISPLAY again while the unit is turned off (on standby).
' . ..." " ""' "'" 0 i..i
= , = ..,, 1... = ,..., ...
1... .1..... • = 1.... , , =
_When you unplug power or power
the AC cord ifa
failure occurs
The power consumption saving mode ("DISPLAY OFF") will be
canceled.
Selectingthe Sourcesand StartingPlay
To select 3-CD Changer as the source, press CD I_ / II.
The unit automatically turns on. (Play starts if a CD is on
the last selected disc tray.)
To stop play, press ll.
• For more detailed operations, see pages 20 to 25.
To select CD Recorder as the source, press CDR I_ / II.
The unit automatically turns on. (Play starts ifa disc is in
CD Recorder.)
To stop play, press ll.
• For more detailed operations, see pages 26 and 27.
To select the tuner and external component as the
source, press SOURCE. The unit automatically turns on.
• Each time you press the button, the source changes as
follows:
[_FM -_AM-_ LINE
FM: To listen to an FM broadcast.
AM: To listen to an AM broadcast.
LINE: To play back the external component connected
to the LINE IN jacks on the rear panel.
• For operating FM/AM, see pages 17 to 19.
For operating the external components, refer to its
manual.
To adjust the input level through the LINE IN jacks
If the sound from the component connected to the LINE IN
jacks is too loud or is not loud enough when changing the
source to "LINE" from another source (without adjusting
the volume level), you can change the input level through
the LINE IN jacks.
On the unit ONLY:
When the source is "LINE," press and hold SET (inside
the sliding panel) repeatedly to select your desired level.
• Each time you press and hold the button, the input level
changes--"LEVEL 1," "LEVEL 2," and "LEVEL 3."
LEVEL 1: Normally select this. (Initial setting when
shipped from the factory.)
LEVEL 2: Select this when the sound is not loud
enough.
LEVEL 3: Select this when the sound is too loud.
-14-