Setting Surface Controls - Frigidaire FEF368CJSD Owner's Manual

Setting Surface
Controls for Models
with Radiant Elements
OFF
1 9
2 8
3
4 6
5
Radiant Surface Unit Control
OFF
1 9
2 8
4 5 6
Dual Radiant Surface Unit Control
OFF
MIN HI
9
8
7
MAX
MED
Simmer Select Surface Unit Control
After turning a Radiant
Surface Unit OFF, be careful not to
touch either unit until it has had enough
time to COOL. Surface Units will turn
dark in color after they have been turned
off and burns may occur if the units are
touched at this time.
Do not place plastic
items such as salt and pepper shakers,
spoon holders or plastic wrappings
on top of the range when it is in use.
These items could melt or ignite.
Potholders, towels or wooden spoons
could catch fire if placed too close to
the unit.
When using the Simmer
Select feature the element will not glow
red when it is hot.
To Operate Radiant Surface Unit
1. Place cooking utensil on the surface element.
2. Push in and turn the Surface Control knob in either direction to the desired
setting. Start most cooking operations on a higher setting and then turn
to a lower setting to finish cooking. The control knobs do not have to be
set exactly on a particular mark. Use the marks as a guide and adjust the
control knob as needed. Each surface unit provides a constant amount of
heat at each setting. A glowing red surface unit extending beyond the
bottom edge of the utensil indicates the utensil is too small for the unit.
3. When cooking is completed, turn the surface element off before removing
the pan. Note: The surface signal light will glow when one or more
elements are turned on. A quick glance at the signal light(s) when cooking
is finished is an easy check to be sure all control knobs are turned off. The
hot cooktop surface light will continue to glow after the control knob is
turned to off and will glow until the element has cooled sufficiently.
To Operate Dual Radiant Surface Unit (If equipped)
Set the rocker switch to the desired coil size.e Indicates inner coil only.
_) Indicates both inner and outer coils operate. You may switch from either
coil setting at any time during cooking. Push in and turn the Control Knob in
either direction to the desired setting as instructed above.
To Operate Simmer Select Surface Unit (If equipped)
The right side of the control knob allows you to use the Simmer Select unit as
you would any normal surface unit on the medium to high settings.
The left side of the control knob is used to operate the Simmer Select feature.
This feature allows the element to heat at a much lower temperature than
when used as a normal surface unit. This allows you to precisely simmer
delicate foods.
You may switch between normal cooking and Simmer Select at anytime during
the cooking process. Be sure to set the knob indicator between MAX and MIN
for simmering or between MED and HI for normal cooking.
NOTE: The unit will not operate if the knob is positioned in the space between
MAX and MED.
The suggested settings found in the chart below are based on cooking in
medium-weight aluminum pans with lids. Settings mayvary when using other
types of pans.
STANDARD AND DUAL RADIANT SURFACE UNITS
Setting Type of Cooking
HIGH (HI - 9) Start most foods, bring water to a boil, pan broiling
MEDIUM HIGH (7 - 8) Continue a rapid boil, fry, deep fat fry
MEDIUM (5- 6) Maintain a slow boil, thicken sauces and gravies,
steam vegetables
MEDIUM LOW (2 - 4) Keep foods cooking, poach, stew
LOW (LO - 1) Keep warm, melt, simmer
SIMMER SELECT SURFACE UNIT
MAX Larger quantities of food, stews and soups
MIN Smaller quanitites of food, delicate foods, melting
chocolate or butter
Note: The size and type of utensil used, and the amount and type of food being
cooked will influence the setting needed for best cooking results.