TYAN Transport TN68 (B4989 Service Manual
  1. Manuals
  2. Brands
  3. TYAN Manuals
  4. Server Board
  5. Transport TN68 (B4989) Service
  6. Service manual
TYAN Transport TN68 (B4989 Service Manual

TYAN Transport TN68 (B4989 Service Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Transport TN68
B4989
Service Engineer's Manual

Advertisement

Table of Contents
loading

Related Manuals for TYAN Transport TN68 (B4989

Summary of Contents for TYAN Transport TN68 (B4989

  • Page 1 Transport TN68 B4989 Service Engineer’s Manual...
  • Page 3 Corporation and has been reviewed for accuracy and reliability prior to ® printing. TYAN assumes no liability whatsoever, and disclaims any ® express or implied warranty, relating to sale and/or use of TYAN products including liability or warranties relating to fitness for a particular purpose or ® merchantability. TYAN retains the right to make changes to produce descriptions and/or specifications at any time, without notice.
  • Page 4 Federal Communication Commission (FCC) Notice for the USA Compliance Information Statement (Declaration of Conformity Procedure) DoC FCC Part 15: This device complies with part 15 of the FCC Rules Operation is subject to the following conditions: This device may not cause harmful interference; This device must accept any interference received including interference that may cause undesired operation.
  • Page 5 About this Manual This manual provides you with instructions on installing your Trans- -port TN68-B4989. This Manual is intended for experienced users and integrators with hardware knowledge of personal computers. This manual consists of the following parts: Chapter1: Provides an introduction to the TN68-B4989 bare- -bones, standard parts list, describes the external components, gives a table of key components, and provides block diagrams of the system.
  • Page 6 SAFETY INFORMATION Before installing and using the Transport TN68-B4989, take note of the following precautions: ·Read all instructions carefully. ·Do not place the unit on an unstable surface, cart, or stand. ·Do not block the slots and opening on the unit, which are provided for ventilation.

  • Page 7: Table Of Contents

    Table of Contents Chapter 1: Overview 1.1 About the TYAN Transport TN68-B4989........1 1.2 Product Models................2 1.3 Features ..................3 1.4 Standard Parts List ..............10 1.4.1 Box Contents ..............10 1.4.2 Accessories ................12 1.5 Optional Parts................13 1.6 About the Product..............14 1.6.1 System Front View .............14...
  • Page 8 2.2.3 Installing the Outer Rails to the Rack .........40 2.2.4 Rack mounting the Server..........40 Chapter 3: Replacing Pre-Installed Components 3.1 Introduction................43 3.2 Disassembly Flowchart..............43 3.3 Removing the Cover..............45 3.4 Replacing Motherboard Components........45 3.4.1 Disconnecting All Motherboard Cables ......45 3.4.2 Removing the Motherboard..........47 3.5 Replacing the Slim DVD-ROM ..........49 3.6 Replacing the LED Control Board ..........51 3.6.1 M1003 LED Control Board Features ........53...

  • Page 9: Chapter 1: Overview

    Chapter 1: Overview 1.1 About the TYAN Transport TN68-B4989 ® Congratulations on your purchase of the TYAN Transport TN68-B4989, a highly-optimized rack-mountable barebone system. The Transport TN 68-B4989 is designed to support four AMD® Opteron™ 8000 series Dual- -core and Quad-core 1207-pin processors and up to 32DIMMs, providing a rich feature set and incredible performance.

  • Page 10: Product Models

    1.2 Product Models Model HDD Bays Power supply 1400W (2+1) B4989T68W8HR-SI Removable, 8 HDDs Redundant PSU 1400W (2+1) B4989T68W8HR-LE Removable, 8 HDDs Redundant PSU Chapter 1: Overview...

  • Page 11: Features

    1.3 Features Transport TN68 B4989 (B4989T68W8HR-SI) Form Factor 2U Rackmount Chassis Name TN68 Dimension (D x W x H) 26.8" x 16.9" x 3.4" (680 x 430 x 87mm) System Motherboard S4989WG2NR-SI Board Dimension MEB, 13"x16.2" (330x411mm) Gross Weight 32 kg Buttons (1) PWR / (1) RST / (1) NMI / (1) ID Front Panel...
  • Page 12 Registered ECC DDR2 800/667/533/400 (800MHz DDR2 speed support available DIMM Type / Speed only at 4xDIMMs per CPU or less) ((8) Dual Rank memory per CPU will have a Memory maximum memory speed of 533MHz) Capacity Up to 256GB Memory channel 2 Channels Memory voltage 1.8V...
  • Page 13 RoHS RoHS 6/6 Complaint Motherboard (1) S4989WG2NR-SI Manual (1) User's manual / (1) Quick Ref. Guide Installation CD (1) TYAN installation CD CPU CEK (4) CPU backplates Chassis Unit (1) CCHA-0300, TN68 2U chassis Peripheral (1) CDVD-0060, slim type DVD-ROM...
  • Page 14 SATA (2) CCBL-0326, SATA signal cables (2) CCBL-067H, Mini-SAS cables (1) CCBL-0422, SATA DVD-ROM power cable / DVD-ROM (1) CCBL-067K, DVD-ROM SAS cable (1) CCBL-0357, USB cable / (1) CCBL-035G, FP USB cable (1) CCBL-146F, Fan BP 2x2P power cable, 300mm / (1) CCBL-146G, Fan BP small 4P power cable / (1) CCBL-039H, fan control cable Package...
  • Page 15 2 Channels Memory voltage 1.8V PCI-E (2) PCI-E x8 slots or (1) PCI-E x16 slots Pre-install TYAN Riser Install M2089, (2) PCI-E x16 slots w/ x8 signal, 2U Expansion Card riser card (left), support full profile add on cards Slots...
  • Page 16 Speed 3.0 Gb/s SATA RAID RAID 0/1/0+1/5 D-Sub 15-pin 1600x1200@60Hz Graphic Chipset XGI Z9s Video RAM 32MB 4 ports ( 2 at front, 2 at rear) 1 port I/O Ports PS/2 1 stacked connector 1 port RJ-45 3 ports (1 port for OPMA) Chipset (1)W83793G +(2) ADT7476/ W83627HG-AW Monitors voltage for CPU, memory, chipset &...
  • Page 17 Contains Manual (1) User's manual / (1) Quick Ref. Guide Installation CD (1) TYAN installation CD CPU CEK (4) CPU backplates Chassis Unit (1) CCHA-0360, TN68-LE 2U chassis Peripheral (1) CDVD-0060, slim type DVD-ROM (1) CCCV-0160, Front Top cover for TN68 chassis...

  • Page 18: Standard Parts List

    The product should arrive packaged as illustrated below. 1.4.1 Box Contents Component Description 2U chassis,(8) hot swap HDDbays ® TYAN Thunder S4989 system board PCI holder (B4989T68W8HR-LE SKU) 1 x slim ODD drive (pre-installed) Air Duct M1003：...
  • Page 19 Component Description M1229-PT HDD Backplane M1022 Fan BD (8) System fans (60mm x 60mm x 38mm) (1) PCI-E fan (60mm x 60mm x 38mm) (3) 700W power supply modules (1)PCI-Ex16 to (2)PCI-Ex8 2U Riser Card (B4989T68W8HR-LE SKU) PCI-Ex16 to PCI-Ex16 1U Riser Card (B4989T68W8HR-LE SKU) Chapter 1: Overview...

  • Page 20: Accessories

    If any items are missing or appear damaged, contract your retailer ® or browse to TYAN ’s website for service: http://www.tyan.com. ® The Web site also provides information on other TYAN products, plus FAQs, compatibility lists, BIOS settings, and more. ® 1 x TYAN...

  • Page 21: Optional Parts

    Rail Kit Rail with Bracket x 2 Screw Sack 1.5 Optional Parts Model Item Picture Quantity Description Number HDD Tray CHDT-0111 Internal 2.5" HDD Tray DVD Dummy TN68 DVD Dummy Cover CMPT-0170 Cover (B4989T68W8HR SKU) Internal 2.5" HDD Power Cable Set CCBL-1070 Cable,100mm (B4989T68W8HR SKU)

  • Page 22: About The Product

    1.6 About the Product The following views show you the product. 1.6.1 System Front View LED control board DVD-Rom drive Hot Swap HDD bays (from HDD1 to HDD8) USB ports ID button Reset button Power button. NMI button 1.6.2 System Rear View B4989T68W8HR-SI: Redundant Power supply Expansion slots...
  • Page 23 B4989T68W8HR-LE Redundant Power Supply Expansion slots Stacked PS/2 mouse & keyboard ports USB ports ID LED USB ports RJ-45 LAN ports Chapter 1: Overview...

  • Page 24: Led Definitions

    1.6.3 LED Definitions Front Panel State Color Description Green System is turned on Power Amber System is turned off Power off Green HDD power on Blinking Green HDD active Amber HDD error HDD LED Blinking Amber HDD rebuild Green/ Random HDD locate Amber Blinking...

  • Page 25: Motherboard (S4989) Layout

    1.6.4 Motherboard (S4989WG2NR-SI) Layout The diagram is representative of the latest board revision available at the time of publishing. The board you receive may not look exactly like the above diagram. Chapter 1: Overview...

  • Page 26: Jumpers & Connectors

    1.6.5 Jumpers & Connectors Jumper/Connector Function J1/J3/J4/J5/J6/J7/J32/J34/J36/J37 Fan connector PSMI header Front Panel header for Barebone System LCM header Front Panel header J20/J21 USB 2.0 header PCI-X Speed Selection BBU Fan connector Clear COMS PCI-E configuration selection XG21 VGA Enable/Disable Jumper IPMB Pin header PCI-X clock frequency 133/100 MHz JP22...

  • Page 27: System Block Diagram

    1.6.6 System Block Diagram Chapter 1: Overview...

  • Page 28: Internal View

    1.6.7 Internal View B4989T68W8HR-SI: ⑧ ⑤ ① ⑥ ② ③ ⑦ ④ System Fan ①/⑥ Air Duct ② M1029 Power backplane ③ Power Cage ④ M1229-PT HDD backplane ⑤ Expansion slots ⑦ HDD Cage ⑧ Chapter 1: Overview...
  • Page 29 B4989T68W8HR-LE: ⑧ ⑤ ① ⑥ ② ③ ⑦ ④ System Fan ①/⑥ Air Duct ② M1029 Power backplane ③ Power Cage ④ M1229-PT HDD backplane ⑤ PCI Holder ⑦ HDD Cage ⑧ Chapter 1: Overview...
  • Page 30 Chapter 1: Overview...

  • Page 31: Chapter 2: Setting Up

    Chapter 2: Setting Up 2.0.1 Before you Begin This chapter explains how to install the CPUs, CPU heatsinks, memory modules, and hard drives. Instructions on inserting add on cards are also given. 2.0.2 Work Area Make sure you have a stable, clean working environment. Dust and dirt can get into components and cause malfunctions.

  • Page 32: Precautions

    2.0.4 Precautions Components and electronic circuit boards can be damaged by discharges of static electricity. Working on a system that is connected to a power supply can be extremely dangerous. Follow the guidelines below to avoid damage to the Transport TN68-B4989 or injury to yourself.

  • Page 33: Installing Motherboard Components

    2.1 Installing Motherboard Components This section describes how to install components on to the motherboa- -rd, including CPUs, memory modules and add on cards. 2.1.1 Removing the Chassis Cover Follow these instructions to remove the Transport TN68 chassis cover. Thumb two screws on the back side as shown in the small diagram.

  • Page 34: Installing The Cpu And Heatsink

    2.1.2 Installing the CPU and Heatsink Follow the steps below on installing CPUs and CPU heatsinks. 1. Pull out the three power supplies: press the button on top of the power supply and pull out the supply in the direction the arrow shows you.
  • Page 35 3. Lift the rack of the power cage and bend it back to an angle of about ° 4. Pull out the pre-installed air duct so you will locate the CPU sockets, the following images show in details. Chapter 2: Setting Up...
  • Page 36 Note: The system supports up to four CPUs, CPU0 must be installed first follow by CPU1, CPU2 and CPU3. For CPU sequence please refer to Chapter 1.5.3. 5. Take off the CPU protection cap; 6. Lift up the CPU lever to unlock the socket, Open the socket cover as the arrow shows;...
  • Page 37 Place the CPU in the socket, ensuring that pin1 is correctly located; 8. Closer the socket cover and press the CPU lever down to secure the CPU; 9. Place the heatsink on top of the CPU and screw it as below; Chapter 2: Setting Up...

  • Page 38: Installing The Memory

    2.1.3 Installing the Memory Follow these instructions to install the memory modules on the motherboard. Your TN68-B4989 boasts up to 32 DIMM sockets. Press the memory slot locking levers in the direction of the arrows as shown in the following illustration. Align the memory module with the slot.
  • Page 39 Single Dual Four DIMM (CPU0) (CPU0 and1) (CPU0,1,2 and3) Quantity of memory installed CPU0_DIMM0 √ √ √ √ √ √ CPU0_DIMM1 CPU0_DIMM2 √ √ √ √ √ √ CPU0_DIMM3 √ √ √ √ √ √ CPU0_DIMM4 √ √ √ √ √...

  • Page 40: Installing Expansion Cards

    2.1.4 Installing Expansion Cards 2.1.4.1 B4989T68W8HR-SI B4989T68W8HR-SI has six expansion slots: 2 × PCI-E×16 slots 2 × PCI-E×4 slots 2 × PCI-X 133MHz slots Follow these instructions to install any of the above kinds of expansion cards. 1. Locate the expansion slot on the motherboard, unscrew the bracket from the slot you want to use.
  • Page 41 Chapter 2: Setting Up...
  • Page 42 2.1.4.2 B4989T68W8HR-LE 1．Unscrew the PCI holder and lift the holder up from the chassis. 2． Turn over the PCI holder and unscrew the bracket from the holder. Insert the PCI-E card into the slot and secure it to the holder. Replace the PCI holder to the chassis, make sure that the holder is correctly inserted into the socket as the images shows you.
  • Page 43 Secure the holder to the chassis follow the above steps in reverse. Chapter 2: Setting Up...

  • Page 44: Installing Hard Drives

    2.1.5 Installing Hard Drives The TN68-B4989 supports eight 3.5” hard drives. Follow these instructions to install a hard drive. Press the locking lever latch and pull the locking lever open. Slide the HDD tray out. Place a hard drive into the HDD tray. Chapter 2: Setting Up...
  • Page 45 Turn over the HDD unit and secure the HDD using 4 HDD screws. Reinsert the HDD tray into the chassis and press the locking lever to secure the tray. Chapter 2: Setting Up...

  • Page 46: Rack Mounting

    2.2 Rack Mounting After installing the necessary components, the Transport TN68-B49 -89 can be mounted in a rack using the supplied rack mounting kit. Rack mounting kit Rail with Bracket x 2 Mounting Ears x 2 Screw Sack x 1 2.2.1 Installing the Server in a Rack Follow these instructions to mount the TN68-B4989 into an industry standard 19”...

  • Page 47: Installing The Inner Rails To The Chassis

    2.2.2 Installing the inner Rails to the Chassis Screw the mounting ear to each side of TN68 as shown using 2 screws from the supplied screws kit. Push the latch key and draw out the inner rails from sliding rails. Install inner rails to left and right sides of chassis using 3 M4 x 5 x P0.7 (A) screws for each side.

  • Page 48: Installing The Outer Rails To The Rack

    2.2.3 Installing the Outer Rails to the Rack Secure the outer rail to the rack using the rail and 4 M4 x 5 x P0.7 (A) screws for each side (A). Secure the mounting brackets from inside, not outside, of the rack (B). 2.2.4 Rack mounting the Server 1.
  • Page 49 3. Push the chassis in and pull the latch key (A). Then push the whole system into the rack (B). 4. Secure the mounting ears of chassis to the rack with 2 M6 x 13 (B) screws. Note: To avoid injury, it is strongly recommended that two people lift the TN68-B4989 into the place while a third person screws it to the rack.
  • Page 50 Chapter 2: Setting Up...

  • Page 51: Chapter 3: Replacing Preinstalled Components

    Chapter 3: Replacing Pre-Installed Components Introduction This chapter explains how to replace the pre-installed components, including the Motherboard, M1003 LED control board, M1229-PT HDD backplane, M1022 FAN board, System fan, ODD drive, Power supply unit etc.. Disassembly Flowchart The following flowchart outlines the disassembly procedure. Rear Components Chassis rear cover DIMMs...
  • Page 52 Front Components Chassis rear cover PCBs M1003 M1229-PT HDD M1029 power M1022 Backplane Control Board board FAN Board Chapter 3: Replacing Preinstalled Components...

  • Page 53: Removing The Cover

    Removing the Cover Before replacing any parts you must remove the chassis cover. Follow Chapter 2.1.1 to remove the cover of the Transport TN68- -B4989. Replacing Motherboard Components Follow these instructions to replace motherboard components, including the motherboard. 3.4.1 Disconnecting All Motherboard Cables Before replacing the motherboard or certain components, remove cables connected to the motherboard.
  • Page 54 Chapter 3: Replacing Preinstalled Components...

  • Page 55: Removing The Motherboard

    3.4.2 Removing the Motherboard After removing all of the aforementioned cables, follow these instructions to remove the motherboard from the chassis. Remove the heatsinks and processors if installed. Remove the eleven screws securing the motherboard to the chassis. Note: You may need to unscrew the front three screws through the holes in the bracket.
  • Page 56 Carefully lift the motherboard from the chassis as the image shows you. Note: The motherboard is too large to lift straight out .Lift the front edge of the board to an angle of about 45 then slides the whole board out. Chapter 3: Replacing Preinstalled Components...

  • Page 57: Replacing The Slim Dvd-Rom

    Replacing the Slim DVD-ROM Follow these instructions to replace the DVD-ROM. Remove the cables from the HDD backplane. Push the stopper in the direction as the arrow shows. Push the DVD through the front of the TN68-B4989. Chapter 3: Replacing Preinstalled Components...
  • Page 58 4. Replace the DVD. 5. Connect the DVD to the backplane follow the above steps in reverse. Chapter 3: Replacing Preinstalled Components...

  • Page 59: Replacing The Led Control Board

    Replacing the LED Control Board Follow these instructions to replace the M1003 LED control board. Remove the two screws securing the LED control board unit to the chassis. Unplug the cables from the connectors on the HDD backplane. Push the LED control board unit out. (Note: You may need a screwdriver to push the board at the rear side.) Chapter 3: Replacing Preinstalled Components...
  • Page 60 4. Remove three screws securing the LED control board to the bracket. 5. Lift the LED control board free from the chassis. After replacem- -ent, insert the unit into the chassis following the above proced- -ures in reverse. Chapter 3: Replacing Preinstalled Components...

  • Page 61: M1003 Led Control Board Features

    3.6.1 M1003 LED Control Board Features 3.6.2 M1003 LED Control Board Connector Pin Definition J2 Front Panel Connector: Definition Definition HDLED+ HDLED- RESET+ RESET- PW_LED+ PW_LED- WLED+ WLED- OCJ_SMBDAT ICH_SMBCLK EXT_INT VOLTAGE5 V5SB INTRU# PWR_SW+ PWR_SW- LAN1_LED+ LAN1_LED- LAN2_LED+ LAN2_LED- Reserve Reserve ID_LED+...
  • Page 62 J1 USB Connector: Definition Definition VCC5 VCC5 USB1- USB0- USB1+ USB0+ KEY PIN Chapter 3: Replacing Preinstalled Components...

  • Page 63: Replacing The System Fan

    3.7 Replacing the System Fan Press the button in the arrow direction and lift out the fan needing replacing. Remove two screws on one side (A) and one screw on the other side of the fan bracket (B). Open the fan bracket and move the connector of the fan in the arrow’s direction.
  • Page 64 Install a new fan into the bracket. Place the FAN unit into the FAN holder Reinsert the fan holder into the chassis and fix it with four screws. Chapter 3: Replacing Preinstalled Components...

  • Page 65: Replacing The M1022 Fan Board

    Replacing the M1022 Fan Board Disconnect all cables connected to the Fan board. Remove screws to release the system fan holder. And lift the system fan holder out. Release all system fans from the fan holder (Refer to 3.7.1) 4. Turn over the system fan holder to remove fourteen screws securing the M1022 Fan Board.
  • Page 66 5. Secure a new M1022 Fan Board to the fan holder and install the whole unit into the chassis following the above steps in reverse. Chapter 3: Replacing Preinstalled Components...

  • Page 67: M1022 Fan Board Features

    3.8.1 M1022 Fan Board Features J1: Fan 8 Connector J2: Fan 4 Connector Fan Tach. Header J10: Power Connector J3: Fan 7 Connector J4: Fan 3 Connector J5: Fan 6 Connector J6: Fan 2 Connector J8: Fan 1 Connector J7: Fan 5 Connector Chapter 3: Replacing Preinstalled Components...

  • Page 68: M1022 Fan Board Connector Pin Definition

    3.8.2 M1022 Fan Board Connector Pin Definition J1~J8: Hot-swapped Fan Connectors (2Pin x 2) Definition Definition POWER FAN_PWM FAN_TACH J9: Fan Tach.Header (9Pin x 2) Definition Definition FAN1_TACH FAN6_TACH FAN2_TACH FAN7_TACH FAN2_TACH FAN8_TACH FAN4_TACH FAN_PWM5 FAN5_TACH FAN_PWM4 KEY PIN FAN_PWM3 HWM_SMBUSC_2 HWM_INT_1 HWM_SMBUSD_2...

  • Page 69: Replacing The M1229-Pt Hdd Backplane

    Replacing the M1229-PT HDD Backplane Step 1: Disconnect all cables connected to M1229-PT HDD backplane. ①. ②. ③. ④. Chapter 3: Replacing Preinstalled Components...
  • Page 70 Step 2: Remove the two screws securing M1229-PT HDD backplane to the chassis base. Step 3: Lift the M1229-PT HDD backplane kit from the chassis. Step 4: Replace a new M1229-PT HDD Backplane and reinstall it into the chassis following the above steps in reverse. Chapter 3: Replacing Preinstalled Components...

  • Page 71: M1229-Pt Hdd Backplane Features

    3.9.1 M1229-PT HDD Backplane Features Front View: J3: Mini SAS J8: Mini SAS Chapter 3: Replacing Preinstalled Components...
  • Page 72 Rear View: Chapter 3: Replacing Preinstalled Components...

  • Page 73: M1229-Pt Hdd Backplane Connector Pin Definitions

    3.9.2 M1229-PT HDD Backplane Connector Pin Definitions Input Power Connectors: PW3: SIGNAL SIGNAL +12V +12V +12V +3.3V PW1: SIGNAL SIGNAL +12V +12V J18: 4P DVD-ROM: SIGNAL +12V J41: CPLD Header: SIGNAL SIGNAL CPLD_JTAG_TCK CPLD_JTAG_TDO NULL VCC- CPLD_JTAG_TDI CPLD_JTAG_YMS J12/J13: USB Header: SIGNAL SIGNAL VDD_5_RUN...
  • Page 74 J11: Front panel Header: SIGNAL SIGNAL ID_SW- GND ID_SW+ ID_LED- ID_LED+ LAN2_LED- LAN2_LED+ LAN1_LED- LAN1_LED+ PWR_SW- PWR_SW+ VOLTAGE5 EXT_INT WLED- WLED+ PW_LED- PW_LED+ RESET- RESET+ HDLED- HDLED+ JP1: Default; SAS\SATA port0 connect Pin_ 3 Pin_1 with mini sas connector SAS\SATA port0 connect with sata Pin_3 Pin_1 port of motherboard...

  • Page 75: Replacing The Power Supply

    3.10 Replacing the Power Supply 3.10.1 Replace the power supply To replace the power supply follow these instructions. Press the tab as shown in the diagram and pull out the power. Free the power from the power socket. You can refer to Chapter 2.1.2 for the above steps. Replace a new single power (FRU NO.: CPSU-0350) and reinsert it into the power socket following the above steps in reverse.
  • Page 76 2. Remove the 9 screws securing M1029 power board to the chassis base. 3. Renew the M1029 and fix it to the chassis following the steps in reverse. Chapter 3: Replacing Preinstalled Components...

  • Page 77: M1029 Power Board Features

    3.10.3 M1029 power board Features PW10 PW12 PW11 Chapter 3: Replacing Preinstalled Components...
  • Page 78 M1029 power board Connector Pin Definitions: PW4: SIGNAL SIGNAL +3.3V +3.3V +3.3V ﹣12V PS_ON PWRGD Reserve 5VSB +12V +12V +3.3V PW7 / PW8: SIGNAL SIGNAL +12V +12V +12V +12V PW 6 / 9 / 10 /12: SIGNAL SIGNAL +12V +12V PW11: SIGNAL SIGNAL...

  • Page 79: Appendix I: Bios Differences

    Appendix I: BIOS Differences The BIOS of B4989 is similar to S4989 while there are some differences in menus. The following table displays those differences in details. For a complete view of S4989 BIOS, please refer to the motherboard manual. BIOS Version information S4989: BIOS Setup Utility...
  • Page 80 B4989: BIOS Setup Utility Main Advanced PCI/PnP Boot Security Chipset Exit System Overview Use [ENTER], [TAB] or [SHIFT-TAB] to select AMIBIOS a field Version : VX.XX.B20 Build Date : DD/MM/YY Use [+] or [-] to : 0AAAA000 configure system time. Processor Quad-Core AMD Optero(tm) Processor XXXX Speed...
  • Page 81 B4989: BIOS Setup Utility Main Advanced PCI/PnP Boot Security Chipset Exit Fan Configuration FAN1 XXXX RPM FAN2 XXXX RPM FAN3 XXXX RPM ← → Select Screen FAN4 XXXX RPM ↑↓ Select Item FAN5 XXXX RPM Change Option FAN6 XXXX RPM Select Field FAN7 XXXX RPM...
  • Page 82 B4989: BIOS Setup Utility Main Advanced PCI/PnP Boot Security Chipset Exit Power Management/APM [Enabled] Enable or Disable APM Power Button Mode [On/Off] Video Power Down Mode [Enabled] Green PC Monitor Power State [Standby] Hard Disk Power Down Mode [Enabled] Hard Disk Time Out (Minute) [Disabled] Force Throttle [Disabled]...

  • Page 83: Appendix Ii: Installing The Internal 2.5"Hdd

    Appendix II: Installing the Internal 2.5”HDD Considering for a multiple choice, the slim DVD-ROM could be replaced by an internal 2.5” SATA HDD in your TN68-B4989. You can choose flexibly in practical application. The internal 2.5”HDD from SATA port has no interference with the other eight 3.5”HDDs from SAS port.
  • Page 84 Step 3: Fix the 2.5”HDD bay onto the chassis using two screws; Step 4: Put the hard disk onto the HDD tray and then place them into the 2.5”HDD bay; Appendix II: Installing the Internal 2.5" HDD...
  • Page 85 Step 5: Screw the HDD onto the HDD tray as the following image shows you; Appendix II: Installing the Internal 2.5" HDD...
  • Page 86 Step 6: Connect the data cables. Appendix II: Installing the Internal 2.5" HDD...
  • Page 87 Appendix III: Replace Pre-installed PCI-E Riser Card Step 1: Unscrew the PCI holder and lift it up from the chassis. Step 2: Turn over the PCI holder and unscrew the M2089 riser card from the holder. Appendix III: Replace Pre-installed PCI-E Riser Card...
  • Page 88 Step 3: B4989T68W8HR-LE supports two types of riser cards, choose the riser card you need and replace it follow the above steps in reverse. M2089 PCI-E Riser Card M2090 PCI-E Riser Card Appendix III: Replace Pre-installed PCI-E Riser Card...

  • Page 89: Appendix Iii: Cable Connection Tables

    Appendix IV: Cable Connection Tables SATA Cables Table 1: M1229-PT HDD Backplane to Motherboard M1229-PT Connect to Motherboard → J21 SATA Connector J14 SATA0 → J15 SATA Connector J15 SATA1 SAS Cables Table 2: M1229-PT HDD Backplane to Motherboard M1229-PT Connect to Motherboard →...
  • Page 90 Power Supply Cables Table 5: M1029 to Motherboard M1029 Connect to Motherboard → PW4 Power Connector PW1 Power Connector → PW7 Power Connector PW3 Power Connector → PW8 Power Connector PW2 Power Connector J2 Power Connector → PW6 Power Connector Table 6: M1029 to M1022 Fan Board M1029 Connect to...
  • Page 91 Other Cables Table 8: M1003 Front Panel LED Board Related Cable M1003 Connect to M1229-PT → J2 Front Panel connector J11 Front Panel connector → J1 USB Header J12 USB Header Table 9: M1229-PT HDD Backplane Related Cables Motherboard M1229-PT Connect to →...
  • Page 92 Appendix IV: Cable Connection Tables...
  • Page 93 Appendix V: FRU Parts Table TN68-B4989 FRU Parts Item Model Number Part Number Picture Quantity Description (4) AMD Opteron™ Rev. F S4989WG2NR 8000/8300 series dual-core/ quad-core processors support (B4989T68W8HR-SI SKU) Motherboard (4) AMD Opteron™ Rev. F S4989WG3NR 8000/8300 series dual-core/ quad-core processors support (B4989T68W9HR-LE SKU) TN68 2U Chassis...
  • Page 94 Item Model Number Part Number Picture Quantity Description 60*60*38mm Fan, 12000rpm, CFAN-0330 336252012309 4-pin 60*60*38mm Fan, 12000rpm, CFAN-0094 336252012297 4-pin Heat Sink & Cooler CHSK-0310 343771000012 CPU Heat Sink Air Duct CADT-0270 340775400006 Air Duct M1003-ID-RS 541174620001 Front Control Board M1022 Fan Adaptor Board M1029...
  • Page 95 A/C Power Cord, US Type, CCBL-0310 332810000280 2440mm A/C Power Cord, EU Type, CCBL-0300 332810000281 1800mm Note: The table is subject to change without notice. Please visit our Web site at http://www.tyan.com for latest update. Appendix V: FRU Parts Table...
  • Page 96 Appendix V: FRU Parts Table...
  • Page 97 's tech support is some of the most impressive we've seen, with great response time and exceptional organization in general.” — Anandtech.com Please feel free to contact us directly for this service at tech-support@tyan.com Help Resources: 1. See the beep codes section of this manual.
  • Page 98 -mber. The RMA number should be prominently displayed on the outside of the shipping carton and the package should be mailed prepaid. ® TYAN will pay to have the board shipped back to you. ® TYAN Transport TN68-B4989 User’s Manual v2.00 Document part No.:...

This manual is also suitable for:

B4989

Table of Contents