Craftsman 917.28626 Operator's Manual page 18

BATTERY
Your tractor has a battery charging system
which is sufficient for normal use, However,
periodic charging of the battery with an au-
tomotive charger will extend its life.
• Keep battery and terminals ctean_
• Keep battery bolts tight.
• Keep small vent holes open.
• Recharge at 6-!0 amperes for 1 hour.
NOTE: The original equipment battery on
your tractor is maintenance free. Do not
attempt to open or remove caps or covers°
Adding or checking level of electrolyte is
not necessary_
TO CLEAN BATTERY AND TERMINALS
Corrosion and dirton the battery and terminals
can cause the battery to "leak" power.
1. Disconnect BLACK battery cable first
then RED battery cable and remove
battery from tractor°
2. Rinse the battery with plain water and dry.
3, Clean terminals and battery cable ends
with wire brush until bright.
4_ Coat terminals with grease or petroleum
jelly_
5. Reinstall battery (See "REPLACING
BATTERY" in the SERVICE AND AD-
JUSTMENTS section of this manual).
TRANSAXLE COOLING
The transmission fan and cooling fins should
be kept clean to ensure proper cooling.
Do not attempt to clean fan or transmission
while engine is running or while the trans-
mission is hot° To prevent possible damage
to seals, do not use high pressure water or
steam to clean transaxle.
• Inspect cooling fan to be sure fan blades
are intact and clean.
• inspectcoolingfinsfordirt, grassclippings
and other materials. To prevent damage to
seals, do not use compressed air or high
pressure sprayer to clean cooling fins.
TRANSAXLE PUMP FLUID
The transaxle was sealed at the factory and
fluid maintenance is not required for the life
of the transaxleo Should the transaxle ever
leak or require servici ng, contact your nearest
Sears or other qualified service center.
Check V-belts for deterioration and wear after
100 hours of operation and replace if neces-
sary. The belts are not adjustable. Replace
belts if they begin to slip from wear,
ENGINE
LUBRICATION
Only use high quality detergent oil rated with
API service classification SG-SL, Selectthe
oil's SAE viscosity grade according to your
expected operating temperature.
18
NOTE: Although multi-viscosity oils (5W30,
10W30 etc,) improve starting in cold weather,
they will result in increased oil consumption
when used above 32°E Check your engine
oil level more frequently to avoid possible
engine damage from running low on oil
Changethe oil after every 50 hours of opera-
tion or at least once a year if the tractor is
not used for 50 hours in one yearn
Checkthe crankcase oil level before starting
the engine and after each eight (8) hours of
operation. Tighten oil fill cap/dipstick se-
curely each time you check the oil level.
TO CHANGE ENGINE OIL
Determine temperature range expected
before oil change,, All oil must meet API
service classification SG-SL
• Be sure tractor is on level surface.
• Oil will drain more freely when warm.
. Catch oil in a suitable container.
I. Remove oil fill cap/dipstick. Be careful
not to allow dirt to enter the engine when
changing oilo
2. Removeyellowcapfrom endofdrainvalve
and install the drain tube onto the fitting.
Oil Drain Valve
Drain
Tube
3, Unlock drain valve by pushing inward
slightly and turning counterclockwise.
4. To open, pull out on the drain valve.
5. After oil has drained completely, close and
lock the drain valve by pushing inward
and turning clockwise until the pin is in
the locked position as shown,
6. Remove the drain tube and replace the
cap onto the end of the drain valve.
7, Refill engine with oilthrough oil fill dipstick
tube. Pour slowly_ Do not overfili, For
approximate capacity see "PRODUCT
SPECIFICATIONS"sectionofthis manual.
8o Use gauge on oil fill cap/dipstick for
checking level. For accurate reading,
insert dipstick into the tube and push
down firmly into place before removing,
Keep oil up to, but not over, the "FULL_
line on dipstick° Push dipstick down firmly
into the tube when finished,