Craftsman 146.669950 Owner's Manual
  1. Manuals
  2. Brands
  3. Craftsman Manuals
  4. Power Tool
  5. 146.669950
  6. Owner's manual

Craftsman 146.669950 Owner's Manual

Wet sharp machine
Hide thumbs

Advertisement

Table of Contents

2905A56
CAT. NO.
146,669950
CAUTION:
Read
Rules
for
Safe
Operation
and
Instructions
Carefully
•
Introduction
•
Operation
owner's manual
_/___/__ / CRAFTSMAN
WET SHARP
MACHINE
Sold by SEARS,
ROEBUCK
AND
CO., Chicago,
IL 60684
US.A.
2905A56

Advertisement

Table of Contents
loading

Related Manuals for Craftsman 146.669950

Summary of Contents for Craftsman 146.669950

  • Page 1 2905A56 owner's manual _/___/__ / CRAFTSMAN WET SHARP MACHINE CAT. NO. 146,669950 CAUTION: Read Rules Safe Operation Instructions Carefully • Introduction • Operation Sold by SEARS, ROEBUCK CO., Chicago, IL 60684 US.A. 2905A56...

  • Page 2: Rules For Safe Operation

    FULL YEAR WARRANTY ON CRAFTSMAN SHARP MACHINE If this Craftsman Wet Sharp Machine fails to give complete satisfaction within one year from the date of purchase, RETURN IT TO THE NEAREST SEARS STORE THROUGHOUT THE UNITED STATES Sears will repair it, free of charge.
  • Page 3 RULES FOR SAFE OPERA TION (Continued) DON'T ABUSE CORD. Never carry tool by cord or yank it to disconnect from ceptacle. Keep cord from heat, oil and sharp edges. SECURE WORK. Use clamps or avise to hold work. It's safer than using your...
  • Page 4 FEATURES AND ADJUSTMENTS HOUSING ON/OFF SCISSOR GUIDE _WER CORD GRINDING WHEEL HOUSING SCREWS ADJUSTABLE TOOL REST WATER RESE BOTTOM FELT WIPER HOUSING SCISSOR BLADE RELIEF ANGLE SELECTOR tOOL REST KNOB GUIDE Fig. 1 RETAINING This unique design Sharp Fig. Machine incorporates features most...
  • Page 5 FILLING COOLING SYSTEM: Loosen tool rest knobs and allow tool rest to hang down as shown in Fig. 4. Re- move wiper as shown in Fig. 3, and soak with water. Replace wiper. Take some water in a container and pour it "SLOWLY,"...
  • Page 6 GENERAL SHARPENING 1/16" CLEARANCE ,...jL..,__(__ Refer to Fig.8. Make sure machine is turned • • ..,,.,.,,,.. ,.,, "OFF" while making adjustments. Loosen both tool rest knobs (1). Slide tool rest (2) along the slot (3) until tip of angle selector arrow (4) is just touching the dot (5) of the angle...
  • Page 7 HINTS 1. Check: While in "OFF" position, use the "visual check" procedure as described on page 6 for proper sharpening angle. 2. Practice: While still in "OFF" position practice procedures as described in the following structions. 3. Deburr: After you are finished sharpening there may be a fine burr on the cutting...
  • Page 8 If blade is curved at the end, rotate knife handle toward when approaching knife's tip as shown in Fig. 14. Sharpen the other side of the blade the same as described above except hold knife as shown in Fig. 15 & 16. Deburr as described on page 7.

  • Page 9: Maintenance

    Fig. 20 You will only need to grind in both angles cutting edge becomes badly damaged. (Fig. 20) BADLY DAMAGED CUTTING EDGE REQUIRING BOTH PRIMARY SECONDARY ANGLES TO BE GROUND. Move the tool back and forth across grinding wheel to avoid wearing down the wheel unevenly.
  • Page 10 NOTES...

  • Page 11: Parts List

    EXPLODED VIEW PARTS LIST Model 146. 669950 DESCRIPTION PART NO. Screw 953A17-1 Housing - Top 2905E2 2905A12 Switch 2901A14 Bearing - Intermediate 500A18 Washer Intermediate Gear & 2905A9 Shaft Ass'y 96A63 Spring Washer 2901A52 Grommet 2901A36 Spherical Bearing Grinding Wheel &...

  • Page 12: Part Description

    owner's manual _/AVR8 _q°'__/PJR_ / CR RFT$ M RN OWNER'S WET SHARP MANUAL MACHINE SERVICE that have purchased your Sharp Machine should a need ever exist for repair parts or service, simply contact Sears Service Center and most Sears, Roebuck and Co.

Table of Contents