Parts List - Craftsman 103.23340 Operating Instructions And Parts List Manual

way the grain emerges on the surface of a piece of
wood. The direction of feed should be governed
accord:ngly; the grain should emerge on the lower
surface of the piece and should point toward the
front of the jolnter.
When surfacing thin stock (_ inch or less), a
push block should always be used.
Because of the cut-out in the lower edge of the
fence, designed for clearance at a maximum depth
of cut setting, a guide surface is not available beyond
the cutter head when surfacing stock less than
inch thick, It may be necessa_ to clamp an auxiliary
face to the fence if a guide is needed under the
above circumstance. This "'face piece"
should
be
attached after the front table position has begn estab-
lished, and should rest on the rear table surface,
The function of the fence in the beveling operation
has been described in the paragraph on controls.
The s_nging guard was incorporated for your
safetyuuse it to its best advantage.
To
be sure you
will
make a depth of cut as
planned, always lower the table beyond the depth
wanted and then crank the table up to the correct
depth.
An interesting booklet covering special opera-
tions which may be performed on your jointer is
available.
PARTS LIST
Part No.
18127
18133
18231
18437
18516
18620
18711
18713
18716
18922
29109
29110
29201
29202
29204
29212
29216
29220
29412
29413
29414
29416
29419
29421
29422
29423
29424
29425
29613
29615
29618
29622
29624
Pa_ Name
Part Na_
Pa_ Name
Cutter blades _ Purchase from nearest
Sears retail store or mail order house,-Ask
for Cat, No, 9-2291
Fence Slide Lock Handle
Ball
Bearing
Washer
Leveling Jack
Hand Wheel with Set Screw
Clevis
Pin
Bracket
Protractor Pointer
Cutterhead Ass*y Complete--_|ncludes
blades, wedges, and set screws
Swinging Guard
Cutter Head with Set Screws
Base with Depth of Cut Scale and Retain-
ing Rings No. 29722
Front Table
Rear Table
Fence Slide
Pulley with Set Screw _ Purchase from
nearest Sears retail store or mail order
house. 2 inch single groove V-pulley
inch bore. Ask for Cat:. No. 9-280t--1/_
inch bore.
Fence Angle Lock Nut
Spacer
Protractor
Swinging Guard Insert
Lower Slide
Upper Slide
Gib, R. H.
Gib, L H.
Fence
Fence Angle _ck Handle
Fence Slide Bar
Elevating Screw
Wedge
Stud
Arbor
29712
29715
29717
29718
29719
29722
29723
29724
29811
*XI09
_XI21
aXi62
*X174
aXI76
aX205
*X210
*X212
*X232
X330
_X420
_X516
X546
*X547
*X605
_X611
*X629
_XII01
*XI326
*X1403
*X2450
_X2951
Fibre Washer
Link
Depth of Cut Scale
Bracket
Depth of Cut Pointer
Retaining Ring
Spacer
Snap Ring
Spring
Set Screw--No. 10--24 x ¼ Slotted Hd.
Cup Point
Setf!crew_5i16--24 x _Socket Hd.
Dog Point
Set Screw_20 x 5_ Slotted Hd. Half
Dog Point
Set Screw 5/1_18 x _ Socket Hd, Cup
Point
Set Screw 5/16_24 x ½ Socket Hd. Cup
Point
Cap
Screw 5/16_18 x _ Hex Hd.
Cap Screw I/_20 x I Hex Hd.
Cap Screw 5/16_18 x 11/_ Hex Hd.
Cap Screw 5/16_ 18 x l _ Hex Hd.
Math. Screw _16 x I_ Phillips-Fil-
lister Hd.
Hex Nut 1_--20,
Math. Screw No. 8--32 x V4 Round Hd,
Math. Screw 1_20 x _ Fillister Hd.
Mach. Screw No. t0_24 x 1_ Round Hd.
Lock Washer 1A I.D. x _ O,D.
Lock Washer 5/16 i.D, x t/_ O,D,
Plain Washer 5/32 I,D. x 5/16 O,D.
Cotter Pin 1/16 x 1/2
Drive Screw No. 4 x 3/16
Allen Wrench 5/32
External Lock Washer No. I 0 I.D. x 13/32
O.D.
Mach. Screw No, 6_32 x 1_ Round Hd.
*Standard hardware items_may be purchased locally.
_is sheet is intended for instruction and repair pa_s only and is not a packing slip.
The parts shown and |istd may in¢lude aecesaories not necessarily part of this t_i,
5