Electrical Requirements; Electrical Connection - KitchenAid KECC051HBL2 Installation Instructions Manual

Electrical
requirements
If codes permit and a separate
ground wire is used, it is
recommended that a qualified
electrician determine that the ground
path and wire gauge are in
accordance with local codes.
Do Not ground to a gas pipe.
Check with a qualified electrician if
you are not sure the cooktop is
properly grounded.
Do Not have a fuse in the neutral or
ground circuit.
This cooktop must be connected to
a metal permanent wiring system.
IMPORTANT:
Save Installation Instructions for
electrical inspector's use.
A.
A three-wire or four-wire, single
phase, 240-volt, 60-Hz, AC-only
electrical supply is required on a
separate, 40-ampere circuit (note: the
KECC051 series requires a 20 ampere
circuit), fused on both sides of the line.
A time-delay fuse or circuit breaker is
recommended. The fuse size must not
exceed the circuit rating of the
appliance specified on the model/serial
rating plate located on the bottom of
the cooktop.
B.
Wire sizes and connections
must conform to the requirements of
the National Electrical Code
ANSI/NFPA 70 – latest edition*, or CSA
Standards C22.1-94, Canadian
Electrical Code, Part 1 and C22.2 No.
0-M91 - latest edition** and all local
codes and ordinances.
C.
The cooktop should be
connected directly to the fused
disconnect or circuit breaker box
through flexible, armored or non-
metallic sheathed, copper cable. The
flexible, armored cable extending from
the fuse box or circuit breaker box
should be connected directly to the
junction box.
4
D.
Locate the junction box to allow
as much slack as possible between the
junction box and the cooktop so that the
cooktop can be moved if servicing is
ever necessary. Do Not cut the conduit.
E.
A U.L.- or CSA-listed conduit
connector must be provided at each
end of the power supply cable (at the
cooktop and at the junction box.)
F.
If the house has aluminum wiring,
follow the procedure below:
a.) Connect the aluminum wiring to the
copper wire by using special
connectors designed and
Underwriters Laboritories-listed for
joining copper to aluminum. Follow
the electrical connector
manufacturer's recommended
procedure.
b.) Aluminum/copper connection must
conform with local codes and
industry-accepted wiring practices.
Copies of the standards listed above may be
obtained from:
* National Fire Protection Association
Batterymarch Park
Quincy, Massachusetts 02269
** CSA International
8501 East Pleasant Valley Road
Cleveland, Ohio 44131-5575
Electrical
connection
For model KECC051 series
only:
WARNING
Electrical Shock Hazard
Turn power supply off before
connecting wires.
Use 12-gauge solid copper wire.
Electrically ground cooktop.
Failure to follow these instructions
can result in death, fire, or
electrical shock.
For all models except
KECC051 series:
WARNING
Electrical Shock Hazard
Turn power supply off before
connecting wires.
Use 8-gauge solid copper wire.
Electrically ground cooktop.
Failure to follow these instructions
can result in death, fire, or
electrical shock.
This cooktop must be connected to
a grounded, metallic permanent
wiring system or a ground connector
should be connected to the ground
terminal or wire lead on the cooktop.
This cooktop is manufactured with a
frame connected, green or bare ground
wire. Connect the cooktop cable to the
junction box through the U.L.- or CSA-
listed conduit connector. Complete
electrical connection according to local
codes and ordinances.
For all cooktop models with
three-wire cable from the
cooktop:
A.
Where local codes Do Not
permit connecting the frame-ground
conductor to the neutral (white)
junction box wire. (Used for
Canadian installations):
4-wire cable from power supply
red wires
bare or green
wires
U.L.- or CSA- listed
conduit connector
3-wire cable
from cooktop
Ungrounded neutral
Figure 1
1. Disconnect power supply.
junction box
white wire
twist-on
connector
black wires