Operating Heater - Desa Comfort Glow CGB3930NRA Owner's Operation And Installation Manual

OWNER'S MANUAL
INSTALLATION
Continued
Piece (#5)
Figure 29 - Installing Log Piece (#5)
OPERATING
HEATER
FOR YOUR SAFETY l
READ BEFORE
LIGHTING
WARNING: If you do not fol-
low these instructions exactly, a
fire or explosion may result caus-
ing property damage, personal
Injury or loss of life.
A. This appliance has a pilot which must
be lighted by hand. When lighting the
pilot, follow these instructions exactly.
B. BEFORE LIGHTING smell all
around the appliance area for gas. Be
sure to smell next to the Boor because
some gas is heavier than air and will
settle on the floor.
WHAT TO DO IF YOU SMELL
GAS
• Do not try to light any appliance.
• Do not touch any electric switch; do
not use any phone in your buildin_
• Immediately call your gas supplier
from a neighbor's phone. Follow
the gas supplier's instructions.
• If you cannot reach your gas sup-
plier, call the tire department.
C. Use only your hand to push in or turn
the gas control knob. Never use tools.
If the knob will not push in or turn
by hand, don't try to repair it, call a
qualified service technician or gas
supplier. Force or attempted repair
may result in a fire or explosion.
D. Do not use this appliance if any part
has been under water. Immediately
call a qualified service technician to
inspect the appliance and to replace
any part of the control system and
any gas control which has been un-
der water.
LIGHTING
INSTRUCTIONS
WARNING:
• If fireplace has glass doors,
never operate this heater with
glass doors closed. If you oper-
ate heater with doors closed,
heat buildup inside fireplacewlll
cause glass to burst. Also if
fireplace opening has vents at
the bottom, you must open the
vents before operating heater.
• You must operate this heater
with a fireplace screen in place.
Make sure fireplace screen is
closed before running heater.
NOTICE: During initial operation
of new heater, burning logs will
give off s paper-burning smell.
Orange flame will also be presenL
Open damper or window to vent
smell This willonlylast a fewhours.
Note: Home owners generally prefer to
operate their heater with the chimney
damper closed. This will put all the heat
into the room. However, there may be
times you will desire the full flames of the
Hi heat setting but will Fundthe heat output
excessive. You can open the chimney
damper (if you have one) fully or partially
to release some of the heat.
I _ WARNING: Damper handle
will be hot If heater has been
running.
1. STOP! Read the safety information
in column 1.
2. Make sure manual shutoff valve is
fully open.
3. Set selector switch in the OFF position.
_k WARNING: Burnerswill come
on automatically within one
minute when the remote selector
switch is In the ON position after
the pilot is lit.
4.
5.
6.
Press in and turn control knob clock-
wise _ to the OFF position.
Wait five (5) minutes to clear out any
gas. Then smell for gas, including
near the floor. If you smell gas,
STOP! Follow "B" in the safety in-
formation, column 1. If you don't
smell gas, go to the next step.
Press in and turn control knob coun-
terclockwise _ to the PILOT
position. Press in control knob for
five (5) seconds (see Figure 30).
Note: You may be running this
heater for the first time after hook-
ing up to gas supply. If so, the con-
trol knob may need to be pressed in
for 30 seconds or more. This will al-
low air to bleed from the gas system.
IgnitorButton
Flame AdjustmentKnob
/l!I
SelectorSwitch in OFF Position
ControlKnob
A
Figure 30 - Control Knob and Ignitor Button Location
Continued
to_,6 _ 15