Subscribe to Our Youtube Channel
Related Manuals for Altinex 400-0226-003
Summary of Contents for Altinex 400-0226-003
- Page 1 MULTI-TASKER MANUAL PART NUMBER: 400-0226-003 MT105-110/MT105-111 8/16-IN, 8-OUT SYNC MATRIX SWITCHER CARDS FOR MULTI-TASKER USER’S GUIDE...
-
Page 2: Table Of Contents
FCC / CE NOTICE...3 ABOUT YOUR MT105-110/111...4 TECHNICAL SPECIFICATIONS...4 DESCRIPTION OF MT105-110/111 ...5 APPLICATION DIAGRAM ...6 INSTALLING YOUR MT105-110/111 ...8 OPERATION ...8 RS-232 CONTROL...8 DESCRIPTION OF COMMANDS ...8 SUMMARY OF COMMANDS..13 TROUBLESHOOTING GUIDE ...13 ALTINEX POLICY ...14 MULTI-TASKER Page... -
Page 3: Precautions / Safety Warnings
MT105-110/111 and to prevent fire and shock hazard. Please read them carefully and heed all warnings. 1.1 GENERAL Qualified ALTINEX service personnel, or their authorized representatives must perform all service. 1.2 INSTALLATION To prevent fire or shock, do not expose this unit to rain or moisture. -
Page 4: About Your Mt105-110/111
RGBHV signal (HSync and VSync. When using these cards to switch RGBHV format signals, it is possible to adapt the 5 BNC connectors to a VGA-type, 15-pin HD connector using ALTINEX adapter cables, such as part # MS8102CA MULTI-TASKER TECHNICAL SPECIFICATIONS... -
Page 5: Description Of Mt105-110/111
MULTI-TASKER DESCRIPTION OF MT105-110/111... -
Page 6: Application Diagram
MULTI-TASKER APPLICATION DIAGRAM... - Page 7 MULTI-TASKER Block Diagrams: Internal View of MT105-110/111...
-
Page 8: Installing Your Mt105-110/111
INSTALLING YOUR MT105-110/111 Step 1. Slide the MT105-110/111 into an available slot in the Multi-Tasker™ Enclosure in order to connect to the bus. Make sure that the MT105-110/111 card fits into place. Secure the card to the Multi- Tasker™ tightening screws located on the top and bottom of the MT105-110/111 card. -
Page 9: Error Codes
Example: If one MT105-110/111 card is in slot #2 of unit When sending command [VERC2U3], Tasker™ Enclosure will return feedback as MT105-111 690-0126-011 2. [C] This command displays the status of the card and connections of the Matrix Switcher. Command Format: [CnUi] Cn = card ID (n = a slot # from 1 to 19) (1 to 8 for MT100-101 or 1 to 4 for MT100-106) Ui = unit id (i = 0 to 9) (refer to the MT100-100... - Page 10 Ix = select input x (x is # from 1 to 16) Oy = connect to output y (y is # from 1 to 8) Cn = card ID number (n is # from 1 to 19) (1 to 8 for MT100-101 or 1 to 4 for MT100-106) Ui = unit ID, i is # from 0 to 9).
- Page 11 [ON…..F]: feedback After processing a command, an OK or ER will be returned as feedback if "F" is included at the end of a command string or if the unit ID is zero. Example: [ON1C2U3F]: if path is not set [ON1C2U3PF]: if path is set 5.
- Page 12 Example: [OFF1C2U3F]: if path is not set [OFF1C2U3PF]: if path is set 6. [SW] – Switch The switch command immediately connects inputs and outputs, which were previously set with the path command on this card or any other cards in the MT100-100. Example: [ON12C6U3P] [ON34C7U3P]...
-
Page 13: Summary Of Commands
If there is still no display present, see Cause Cause 4: The display has a problem. Solution 1: Make sure that the display is powered. If there is still no display, call ALTINEX at (714) 990-2300. MT105-110/(111);... -
Page 14: Altinex Policy
ALTINEX POLICY 9.0 LIMITED WARRANTY / RETURN POLICY Please see the Altinex website at for details on warranty and return policy. 9.1 CONTACT INFORMATION ALTINEX, INC. 592 Apollo Street Brea, CA 92821 USA TEL: 714-990-2300 TOLL FREE: 1-800-ALTINEX WEB: www.altinex.com E-MAIL: solutions@altinex.com...
Need help?
Do you have a question about the 400-0226-003 and is the answer not in the manual?
Questions and answers