Related Manuals for Altinex MT107-103
Summary of Contents for Altinex MT107-103
- Page 1 MULTITASKER™ MANUAL PART NUMBER: 400-0367-004 MT107-103 64X64 AUDIO MATRIX SWITCHER FOR MULTITASKER™ USER’S GUIDE...
-
Page 2: Table Of Contents
TECHNICAL SPECIFICATIONS ......3 PRODUCT DESCRIPTION ........4 APPLICATION DIAGRAM ........5 DIAGRAM 1: TYPICAL CONFIGURATION ..5 DIAGRAM 2 INTERNAL VIEW ......6 INSTALLING YOUR MT107-103 ......7 OPERATION............... 7 RS-232 CONTROL..........7 DESCRIPTION OF COMMANDS .......7 SUMMARY OF COMMANDS ......22 MENU MODE ...........22 TROUBLESHOOTING GUIDE ...... -
Page 3: Precautions / Safety Warnings
MT107-103. Keep this manual handy for future These limits are designed to provide reasonable reference. These safety instructions are to ensure protection against harmful interference when the the long life of your MT107-103 and to prevent fire equipment operated commercial and shock hazard. -
Page 4: About Your Mt107-103
MT107-103 FEATURES/ MT107-103 DESCRIPTION 64 X 64 Audio Matrix Engine GENERAL The MT107-103 is a 64X64 Matrix Engine used for 8 (2 per Term. Block) Inputs connecting balanced audio signals. The Matrix Input Connectors 5-pin Term. Block Engine has 8 balanced audio inputs and 8 Outputs 8 (2 per Term. -
Page 5: Product Description
MULTITASKER™ PRODUCT DESCRIPTION 400-0367-004... -
Page 6: Application Diagram
MULTITASKER™ APPLICATION DIAGRAM DIAGRAM 1: TYPICAL CONFIGURATION MT107-103 400-0367-004... -
Page 7: Diagram 2 Internal View
MULTITASKER™ DIAGRAM 2 INTERNAL VIEW MT107-103, 64X64 Audio Matrix Engine OUT1 OUT2 OUT3 OUT4 64X64 MATRIX IN61 OUT61 IN62 OUT62 IN63 OUT63 IN64 OUT64 MAIN POWER SUPPLY 400-0367-004... -
Page 8: Installing Your Mt107-103
MULTITASKER™ 7.1.1 RS-232 INTERFACE INSTALLING YOUR MT107-103 The RS-232 commands, for the MT107-103 are Step 1. Determine the number of slots required in a simple ASCII character format. for the MT107-103, including the add-on cards. The base MT107-103 requires two Square brackets “[ ]”... - Page 9 Ui = Unit ID (i = # from 0 to 9) Example: Example: There is an MT107-103 in slot 5, sending the command, [C5], will return feedback similar to Clear the MT107-103 with Engine Card in slot 5. the following: To do this, send the command [CLRC5].
- Page 10 Ui = Unit ID (i = # from 0 to 9) power up. In order to change the power up default Example: without having to redefine the settings, There is an MT107-103 card is in slot 5. Send see the command [MjCnS]. the command the MultiTasker will [VERC5] and...
- Page 11 MULTITASKER™ Number of Outputs: Same as for Inputs. Default Configuration Input Offset: The offset defines where Input INPUT CARDS OUTPUT CARDS #1 will be in reference to Input #1 on the … … Input Connector Card. Typically, Input #1 Base Base would be Input #1 of the base card.
- Page 12 16a 12a 8a 8a 12a 16a Example: 16b 12b 8b 8b 12b 16b There is an MT107-103 in slot 5. Turn ON ALL 6. [MjCn] outputs by sending the command [ONC5]. This command selects the matrix to be active. 9. [OFFmmCn]...
- Page 13 Example 1: Cn = Card ID (n = slot # from 1 to max slots) There is an MT107-103 in slot 5. Input 1 is connected to Output 1. Send the command Ui = Unit ID (i = # from 0 to 9)
- Page 14 MULTITASKER™ Example: 15. […P] – Path This command will set the path for the output, The Engine Card is in slot 5. Adjust the volume on Input 2. The current volume level is set to 10. but it is not active until the switch command, [SW], is executed.
- Page 15 MULTITASKER™ Example: Example 1: Adjust Input 1 volume level for the card in slot 5. Check for a signal on Input 1 of the engine in The current input level is 10, but it is not the slot 5 by sending the command [SDI01C5]. If optimal value.
- Page 16 Example: [O07S0C05] [O08S0C05] In order to display the RS-232 commands … [O63S0C05] [O64S0C05] available for the MT107-103 in slot 5, send the 23. [MODE] command [HELPC5]. The commands along with This command sets the matrix switch mode to a brief description will be displayed.
- Page 17 = Input Volume 33-48 Example: (VD323232…32C05 ) = Input Volume 49-64 The MT107-103 in slot 5 has Input 1 connected = End Feedback to all outputs. Outputs 1-4 are on and 5-64 are NOTE: The VIS information applies to video off.
- Page 18 Firmware Version from the card and front panel. The command affects any card with auto-feedback capability, Input Selected not just the MT107-103 The default at power on Output Connections 01-16 or reset is STA0, OFF. Output Connections 17-32 Command Format: [STA0]...
- Page 19 MULTITASKER™ SAMPLE FEEDBACK MATRIX CONFIGURATION [(MT107-104C05)(VR690-0159-004C05) Matrix Number (ME1646400000100C05) Inputs (MA01010101010101010101010101010101C05) Outputs Input Offset (MB01010101010101010101010101010101C05) Output Offset (MC01010101010101010101010101010101C05) Channel Width (MD01010101010101010101010101010101C05) Channel Spacing (ON11110000000000000000000000000000C05) +ME1 646400000100 C05 (OL00000000000000000000000000000000C05) (VV0C05)(MM0C05) (VA32323232323232323232323232323232C05) (VB32323232323232323232323232323232C05) (VC32323232323232323232323232323232C05) (VD32323232323232323232323232323232C05)] MATRIX CONNECTIONS INPUT VOLUME SETTINGS Output 1 to Input 1 Input 1 Volume Output 2 to Input 1 Input 2 Volume...
- Page 20 MULTITASKER™ Command Format: [RSI] CARD ID COMMANDS The default Card ID is the same as the card slot Example: number. The next several commands allow the Send the command [RSI] to the system with user to change the Card ID to a value other than Unit ID 0.
- Page 21 MULTITASKER™ Example: Group 1 = Video Cards Group 2 = Audio Cards There are two, 20 slot enclosures to be Group 3 = Video and Audio Cards connected together during normal operation. The first unit will use the Card ID defaults which assigning group commands...
- Page 22 MULTITASKER™ Example: 39. [RMG] This command may be used to delete an entire The cards in slots 1, 2 and 19 are part of group 5. Read the member data for group 5, by group, or all groups. sending the command [RDG5]. The system will REMOVE A GROUP return feedback as follows: Remove all the members from the group,...
-
Page 23: Summary Of Commands
MULTITASKER™ Example: 20) [VOL] Set absolute volume level Group 5 of Unit ID 1 contains the cards in slots 21) [SDI] Input signal detect 1, 2 and 19. Read the member data for group 5 22) [SDO] Output signal detect of Unit ID 1. - Page 24 [SW] "08" will force the system back to the Signal Detect [SDImmCn], [SDOmmCn] original prompt. Version [VER] After selecting the MT107-103 as described Status [Cn] above, the system will prompt for selections HELP [HELP] specific to that card. Save Settings [CnS], [..S]...
- Page 25 7.4.4 MT107-103 MENUS ESC: GO BACK Following are the menus available to the KEY= MT107-103. The first menu is the Main Menu 5: SET OUTPUT OFFSET (00) only. The second listing is an expansion of all SET OUTPUT OFFSET (00-63) the menu items available.
- Page 26 1: ALL OUTPUTS ON MENU MODE examples assume 2: ALL OUTPUTS OFF MT107-103 is installed in slot 5. Start by clicking ESC: GO BACK the mouse in the Terminal window. Press KEY= ENTER and a list of available cards will be displayed.
-
Page 27: Troubleshooting Guide
4. Turn off all outputs. card’s LED lights in that slot. If it Starting from the MT107-103 Main Menu, set all lights, then the original card may be outputs off. Follow the keystrokes below. -
Page 28: No Sound
E-MAIL: solutions@altinex.com there is still no sound, see Cause 4. Cause 4: receiving device problem. Solution: Make sure the receiving device has power and is turned on. If there is still no sound, please call Altinex at (714) 990-2300. 400-0367-004...
Need help?
Do you have a question about the MT107-103 and is the answer not in the manual?
Questions and answers