Related Manuals for Altinex MT110-104
Summary of Contents for Altinex MT110-104
- Page 1 ™ MULTITASKER MANUAL PART NUMBER: 400-0347-001 MT110-104 16 X 16 BALANCED STEREO AUDIO MATRIX SWITCHER CARD ™ FOR MULTITASKER...
-
Page 2: Table Of Contents
PRECAUTIONS / SAFETY WARNINGS ....1 GENERAL ............2 INSTALLATION..........2 CLEANING............2 FCC / CE NOTICE..........2 ABOUT YOUR MT110-104........3 TECHNICAL SPECIFICATIONS......3 FRONT PANEL DIAGRAM OF MT110-104...4 APPLICATION DIAGRAM ........5 APPLICATION EXAMPLE ........5 BLOCK DIAGRAM..........6 INSTALLING YOUR MT110-104 ......7 OPERATION ............7 RS-232 CONTROL..........7 RS-232 COMMANDS .........7 DESCRIPTION OF COMMANDS .......7... -
Page 3: Precautions / Safety Warnings
These safety instructions are to ensure interference when the equipment is operated the long life of your MT110-104 and to prevent fire in a commercial environment. This equipment and shock hazard. Please read them carefully and generates, uses, and can radiate radio heed all warnings. -
Page 4: About Your Mt110-104
40,000 hrs blocks. Table 2. MT110-104 Mechanical Although designated as a 16x16 matrix switcher, the ELECTRICAL MT110-104 can be used in a variety of ways to Input Signals provide different capabilities. For example, one Max Level 0dBu MT110-104 can be used to create two 8x8 stereo... - Page 5 ™ MULTITASKER...
-
Page 6: Front Panel Diagram Of Mt110-104
™ MULTITASKER FRONT PANEL DIAGRAM OF MT110-104 TOP RETAINER SCREWS BOTTOM RETAINER SCREWS 16 BALANCED 16 BALANCED STEREO OUTPUTS STEREO INPUTS... -
Page 7: Application Diagram
™ MULTITASKER APPLICATION DIAGRAM APPLICATION EXAMPLE: AMPLIFIERS / SPEAKERS STEREO CONNECTS TO CONNECTS TO INPUTS 9-16 INPUTS 1-8... -
Page 8: Block Diagram
™ MULTITASKER BLOCK DIAGRAM: OUTPUT ON/OFF CONTROL TERMINAL BLOCKS TERMINAL BLOCKS IN 1 OUT 1 GAIN IN 2 OUT 2 GAIN MATRIX IN 3 OUT 3 GAIN SWITCHER IN 4 OUT 4 GAIN IN 5 OUT 5 GAIN IN 6 OUT 6 GAIN OUT 7... -
Page 9: Installing Your Mt110-104
™ MULTITASKER INSTALLING YOUR MT110-104 7.3. DESCRIPTION OF COMMANDS Step 1. Slide the MT110-104 into an available slot Each command consists of three parts: in the MultiTasker™ enclosure in order to function, card ID, and an optional unit ID. connect to the bus. Make sure that the [Function, Card ID, Unit ID] MT110-104 card fits into place. - Page 10 Ci = card ID number (i = number from 4 to 19) Example: This command disables the selected output without affecting any other outputs. If one MT110-104 card is in slot #8 of unit #3: Command Format: [OFFnCi] Send command [VERC8U3 n = Output number from 1 to 16 MultiTasker™...
- Page 11 ™ MULTITASKER Command Format: [OSImCi] the MT110-104 Matrix Switcher as 16x16, 8x8, 4x4 or 2x2 m = offset value from 0 to 128 Command Format: [MATmXnCi] Ci = card ID number (i = number from 4 to 19) mXn = matrix size: 16X16, 8X8, 4X4 or 2X2...
- Page 12 ™ MULTITASKER e.g. : [I1O2C5] will connect input1a to Input Output output2a, 1b to 2b, 1c to 2c, and 1d to 2d, 1e to 2e, 1f to 2f, 1g to 2g, and 1h to 2h. 7.3.12. [CLR] This command resets the card selected to the factory default configuration (Input 1 to all Outputs, all Outputs ON).
-
Page 13: Summary Of Commands
If "F" is included use the [OFFmCnUiPF] command or the [OFFmCnUiFP] command. We have carefully tested and have found no problems in the supplied MT110-104. However, we 7.3.16. [SW] would like to offer suggestions for the following: The switch command immediately connects 8.1. -
Page 14: Altinex Policy
Note: Test the system by removing the MT110- 104 card from between the source and the destination amplifier. If problem persists, call ALTINEX at (714) 990-2300 or 1-800- ALTINEX.
Need help?
Do you have a question about the MT110-104 and is the answer not in the manual?
Questions and answers