Related Manuals for Altinex MULTI-TASKER MT105-106
Summary of Contents for Altinex MULTI-TASKER MT105-106
- Page 1 MULTI-TASKER MT105-106/109 is shown above. MANUAL PART NUMBER: 400-0223-002 MT105-106/MT105-107/MT105-109 6X2; 4X4; 2X6 VIDEO/SYNC MATRIX SWITCHER (BNC IN/OUT) FOR MULTI-TASKER USER’S GUIDE...
-
Page 2: Table Of Contents
PRODUCT DESCRIPTION……………………… 5 APPLICATION DIAGRAM……………………….. 6 SETTING INPUTS AND OUTPUTS……………. 6 BLOCK DIAGRAM……………………………….. 7 INSTALLING YOUR MULTI-TASKER™……….. 7 OPERATION……………………………………… 7 RS-232 CONTROL…………………………….. 7 RS-232 INTERFACE…………………………... 7 DESCRIPTION OF COMMANDS…………….. 8 SUMMARY OF COMMANDS…………………. 12 TROUBLESHOOTING GUIDE………………….. 13 ALTINEX POLICY………………………………… 13... -
Page 3: Precautions / Safety Warnings
These safety instructions are to interference when the equipment is operated ensure the long life of your MT105-106/107/109 in a commercial environment. This equipment and to prevent fire and shock hazard. Please read generates, uses, and can radiate radio them carefully and heed all warnings. -
Page 4: About Your Multi-Tasker
T° Operating 10°C-50°C T° Maximum 75°C Humidity 90% non-condensing Multiple MT105-106 cards can be installed in the MTBF (calc.) 50,000 hrs enclosure to provide additional functionality. For example, three cards to handle Component Video. Table 2. MT105-106/109 Mechanical If you need to switch signals use MT105-107. -
Page 5: Product Description
Impedance 75 Ohms 10 KOhms Analog 1.5V p-p max. TTL/Analog Output Signals Impedance 75 Ohms 22 Ohms Gain 1.05 Bandwidth 220 MHz @ -3dB MT105-106 100 MHz @ -3dB MT105-109 Table 3. MT105-106/107/109 Electrical MT105-106/107 Back Pannel MT105-109 Back Pannel... -
Page 6: Application Diagram
MULTI-TASKER APPLICATION DIAGRAM SETTING INPUTS AND OUTPUTS Location of configuration jumpers... -
Page 7: Block Diagram
MULTI-TASKER BLOCK DIAGRAM INSTALLING YOUR MULTI-TASKER™ OPERATION Step 1. Slide the MT105-106/107/109 into an 9.1 RS-232 CONTROL available slot in the Multi-Tasker™ When used in the Multi-Tasker™ Enclosure, the Enclosure in order to connect to the MT105-106/107/109 has many advanced remote bus. -
Page 8: Description Of Commands
Commands such as [ON], [OFF], and [IO] that Example: end in "S" will be saved into memory. If one MT105-106/107/109 card is in slot #2 of Commands not ending in "S" will still be unit 3. When sending command [VERC2U3], executed but will not be restored when the Multi- Tasker™... - Page 9 Card 2 of Unit 0. Example: 6. [ON] If one MT105-106/107/109 card is in slot #2 of This command enables one or more outputs of a unit 3 with output 1, 2 and 3 ON: single card or group of cards.
- Page 10 MULTI-TASKER [ONmGkUiS]: for a group of cards Example: This command enables output "m" for each card [ON1C2U3F]: if path is not set in group "k" of unit "i". [ON1C2U3PF]: if path is set m = card output (m = # from 1-6) 7.
- Page 11 MULTI-TASKER [OFFG5U1]: Turns OFF all outputs for each Example: card in group 5 of unit 1. [ON12C6U3P] [OFF…..P]: sets path [ON34C7U3P] [SW] This command will set the path for the output, but it is not active until the switch command is The system will return feedback as OK if the unit executed ( [SW] ).
-
Page 12: Summary Of Commands
MULTI-TASKER k = group number (k = # from 1-9) k = group number (k = # from 1-9) i = unit number (i = # from 0-9) i = unit number (i = # from 0-9) Example: member = C1 - C19 (card 1 to 19) (1 to 8 for MT100-101 or 1 to 4 for MT100-106) To group card #1, 2 and 3 as group 5 of unit #1, send the [WRC1C2C3G5U1] command. -
Page 13: Troubleshooting Guide
592 Apollo street Brea, CA 92821 USA TROUBLESHOOTING GUIDE TEL: 714 990-2300 We have carefully tested and have found no TOLL FREE: 1-800-ALTINEX problems in the supplied MT105-106/107/109; WEB: www.altinex.com however, we would like to offer suggestions for the E-MAIL: solutions@altinex.com...
Need help?
Do you have a question about the MULTI-TASKER MT105-106 and is the answer not in the manual?
Questions and answers