Subscribe to Our Youtube Channel
Related Manuals for Altinex MULTI-TASKER MT105-108
Summary of Contents for Altinex MULTI-TASKER MT105-108
- Page 1 MULTI-TASKER™ MANUAL PART NUMBER: 400-0218-003 MT105-108 6X2; 4X4; 2X6 VGA - QXGA MATRIX SWITCHER (15 Pin HD IN/OUT) FOR MULTI-TASKER USER’S GUIDE 400-0218-003...
-
Page 2: Table Of Contents
RS-232 CONTROL ..........7 DESCRIPTION OF COMMANDS.......7 SUMMARY OF COMMANDS ......15 MENU MODE...........16 TROUBLESHOOTING GUIDE ......20 LED IS NOT LIT ..........20 CARD IS NOT RECOGNIZED ......20 LED IS BLINKING RED........20 NO DISPLAY ...........21 ALTINEX POLICY ..........21 LIMITED WARRANTY/RETURN POLICY..21 CONTACT INFORMATION ......21 400-0218-003... -
Page 3: Precautions / Safety Warnings
These limits are designed to provide reasonable future reference. These safety instructions are to protection against harmful interference when ensure the long life of your MT105-108 and to the equipment is operated in a commercial prevent fire and shock hazard. Please read them environment. -
Page 4: About Your Multi-Tasker
Impedance 22 ohms Signal Level 4.5 Volts TTL A special feature of the MT105-108 is Sync Delay Table 3. MT105-108 Electrical to eliminate the appearance of video signals before the display device is able to process the sync signals and properly format the video image. -
Page 5: Product Description
MULTI-TASKER™ PRODUCT DESCRIPTION DEDICATED OUTPUTS RE-CONFIGURABLE I/O PORTS DEDICATED INPUTS 400-0218-003... -
Page 6: Application Diagrams
MULTI-TASKER™ APPLICATION DIAGRAMS DIAGRAM 1 - TYPICAL CONFIGURATION DIAGRAM 2 - INTERNAL VIEW EXP 1 POWER CONTROL OUTPUT OUTPUT 1 INPUT 1 OUTPUT 2 INPUT 2 MATRIX SWITCHER INPUT 6 IN 6/OUT 3 INPUT 5 IN 5/OUT 4 INPUT 4 IN 4/OUT 5 INPUT 3 IN 3/OUT 6... -
Page 7: Diagram 3 - Jumper Locations
MULTI-TASKER™ DIAGRAM 3 - JUMPER LOCATIONS 1-800-ALTINEX www.altinex.com 285-0388-001 LED1 R110 R117 R103 R111 R118 R104 R112 R119 R105 R113 R120 R107 R100 R114 R121 R106 R116 R123 R109 R102 R115 R122 R101 R108 Connect the ribbon cable jumpers as indicated for the desired Matrix configuration. -
Page 8: Installing Your Multi-Tasker
]” are part of the is a 10-pin ribbon cable assembly. command. Step 3. Slide the MT105-108 into an available 2. Use uppercase letters for all commands. slot in the Multi-Tasker™ Enclosure in order to connect to the bus. Make sure After processing a command, an OK or ER will that the MT105-108 card fits into place. - Page 9 [VERC4], and the Multi-Tasker™ Enclosure will return the following feedback: Example: MT105-108 690-0170-003 There is an MT105-108 in slot #4. Input 1 is connected to all outputs, but only outputs 1 MT105-108 = the card model through 3 are ON. The feedback after sending...
- Page 10 Example: [690-0122-015 690-0123-004 690-0124-018] There is an MT105-108 in slot #4. Send the command [SDLC4] and feedback similar to the Check the last three digits against the numbers following: above to determine if the MENU MODE option is available.
- Page 11 MT105-108. The default at power Example: on or reset is STA0, OFF. There is an MT105-108 card in slot #5. All of Command Format [STA1] = ON the outputs on the card are OFF. Command Format [STA0] = OFF...
- Page 12 This command disables output "m" for each Example: card in group "k" of unit "i". There are two MT105-108 cards in slots 6 and = Card output (m = # from 1-7) 7. Enable Output 1 of card 6 and Output 3 of card 7 simultaneously.
- Page 13 [OFF3C7P] [SW] Example: 14. [IO] There is an MT105-108 in slot #4. Currently, Input 1 is connected to all outputs and all This command will connect a single input with outputs are ON. The PATH command has been one or all outputs. It will not effect the ON/OFF used to set Input 2 to Output 1 and turn OFF status of the output.
- Page 14 Command Format: [HELPCnUi] Cn = Card ID (n = # from 1 to max slots) An MT105-108 is in slot #4 Connect Input 1 to all outputs by sending the command [I1O[C4]. Ui = Unit ID (i = # from 0 to 9)
- Page 15 MULTI-TASKER™ Example: 19. [RMC] Group 1 consists of cards 1 and 2. Group 2 This command may be used to remove one or consists of cards 1, 2, 3, 4 and 5. Delete all the more group members from a group. groups by sending the command [RMG[].
-
Page 16: Summary Of Commands
MULTI-TASKER™ Example: 7.3 SUMMARY OF COMMANDS 1) To clear group 1 of Unit ID 0, send the Card Commands [CLRG1] command. This command clears Receives software version [VER] the members for the specified group only. Receives status of the card 2) To clear all groups of Unit ID 1, send the [CLRG[U1] command. -
Page 17: Menu Mode
"4" will force the system back to the original Setup prompt. Sync Delay [SDL], [SDLm] Group [WR], [RM], [CLM] 7. After selecting the MT105-108 as described Status [VER], [C] above, the system will prompt for selections Help [HELP] specific to that card. - Page 18 7.4.4 MT105-108 MENUS 3: STATUS 4: HELP Following are the menus available to the ESC: GO BACK MT105-108. The first menu is the Main Menu only. The second listing is an expansion of all KEY= the menu items. MT105-108 EXPANDED MENUS...
- Page 19 MULTI-TASKER™ 2: SAVE (Card Settings) In1-Out1 ON 2: SETUP In1-Out2 ON 1: SET GROUP ID In1-Out3 ON CURRENT GROUP ID: NONE In1-Out4 ON 1: ASSIGN GROUP ID In1-Out5 ON ASSIGN GROUP ID: ENTER NUMBER In1-Out6 ON In1-Out7 ON 1: Group 1 SAVE THIS SETTING? 2: Group 2 3: Group 3...
- Page 20 3. Set Sync Delay for Output 1 to 2 seconds. MT105-108 is installed in slot #4. Start by clicking the mouse in the Terminal window. Starting from the Main Menu, set the Sync Press ENTER and a list of available cards will Delay for Output 1 to 2 seconds.
-
Page 21: Troubleshooting Guide
Cause 2. We have carefully tested and have found no Cause 2: Card is not plugged in all the way. problems in the supplied MT105-108; however, we Solution: Push the card in all the way. Reset would like to offer suggestions for the following: the system and send the [C] 8.1 LED IS NOT LIT... -
Page 22: No Display
592 Apollo Street Solution 2: Turn the system OFF and then ON Brea, CA 92821 USA again. If there is still an error, call TEL: 714 990-2300 ALTINEX at (714) 990-2300. TOLL FREE: 1-800-ALTINEX 8.4 NO DISPLAY WEB: www.altinex.com Cause 1: The source has a problem.
Need help?
Do you have a question about the MULTI-TASKER MT105-108 and is the answer not in the manual?
Questions and answers