Related Manuals for Altinex Dual Twisted Pair Receiver to Computer / Component Video + Audio MT115-111
Summary of Contents for Altinex Dual Twisted Pair Receiver to Computer / Component Video + Audio MT115-111
- Page 1 ® MULTITASKER MANUAL PART NUMBER: 400-0443-004 MT115-111 DUAL TWISTED PAIR RECEIVER TO COMPUTER/COMPONENT VIDEO + AUDIO, USER’S GUIDE...
-
Page 2: Table Of Contents
CARD CONTROL ...13 ID COMMANDS ...14 GROUP COMMANDS...15 SUMMARY OF COMMANDS ...16 MENU MODE ...17 TROUBLESHOOTING GUIDE... 19 ARE OFF ...19 DISPLAY IS TOO BRIGHT ...19 NO DISPLAY...20 ALTINEX POLICIES ... 20 LIMITED WARRANTY/RETURN POLICIES ...20 CONTACT INFORMATION ...20 400-0443-004 Page MULTITASKER... -
Page 3: Precautions / Safety Warnings
Any changes or modifications to the unit not expressly approved by ALTINEX, Inc. could void the user’s authority to operate the equipment. discharge (ESD). -
Page 4: About Your Mt115-111
The MT115-111 provides a means of receiving computer or component video and audio signals over Twisted Pair-type (CAT-5) cable when used together with an ALTINEX Twisted Pair Video Transmitter, such as the MT115-110 or TP115-110. The MT115-111 offers two 15-pin HD female outputs and two 3.5 mm audio outputs, one for... - Page 5 Video Resolutions 480p through 1080i Power (from enclosure) Total Power Consumption Table 3. MT115-111 Electrical 400-0443-004 MT115-111 ALTINEX Standard 0 dB +/- 0.5 dB 1.0 Vp-p max 1.0 Vp-p max 75 ohm TTL (+/-) 0.600 A (3.6 W) 0.350 A (2.1 W) 5.7 W max.
-
Page 6: Product Description
MULTITASKER PRODUCT DESCRIPTION 400-0443-004... -
Page 7: Application Diagrams
MULTITASKER APPLICATION DIAGRAMS DIAGRAM 1: TYPICAL SETUP MT115-111 TP115-110 TP115-110 400-0443-004... -
Page 8: Diagram 2: Internal View
DIAGRAM 2: INTERNAL VIEW PAIR 4 INPUT 1 PAIR 2 RJ-45 PAIR 3 PAIR 1 PAIR 4 INPUT 2 PAIR 2 RJ-45 PAIR 3 PAIR 1 400-0443-004 MT115-111 SYNC SEPARATOR SYNC SEPARATOR MULTITASKER SIGNAL POWER DETECT SIGNAL POWER DETECT R/Pr B/Pb 15-PIN HD R/Pr... -
Page 9: Diagram 3: Switch Settings
DIAGRAM 3: SWITCH SETTINGS GAIN2 CONTROL OUTPUT Video Gain Equalization Sync-on-Green 400-0443-004 GAIN1 CONTROL DESCRIPTION Set SW6 to SW for software or HW for a fixed gain = 1. Set SW8 to SW for software or HW for a fixed gain = 1. Set SW4 to SW for software or HW for hardware. -
Page 10: Installing Your Mt115-111
INSTALLING YOUR MT115-111 Step 1. Determine the appropriate switch settings using DIAGRAM 3 on page 8. Step 2. Turn off power to the MultiTasker system and disconnect from AC power. Step 3. Remove unused (MT200-101). Identify the slot number and note that it is for RS-232 control. -
Page 11: Description Of Commands
7.2 DESCRIPTION OF COMMANDS Each command consists Function, Card ID, and Unit ID. [ Function , Card ID , Unit ID ] Example: [VERC3U2] = Function = Card ID or Group ID = Unit ID (optional for Unit ID 0) For Function, see a detailed explanation under each command description. - Page 12 2. [C] This command receives the status of the card. Command Format: [Cn] Cn = Card ID (n = # from 1 to max slots) Example: There is one MT115-111 card in slot 4. Sending the command [C4] to the system will yield feedback similar to the following: INPUT#1 VIDEO GAIN 4 EQUALIZATION 32...
-
Page 13: Feedback Control
FEEDBACK CONTROL The next commands are a function of both the card and the front panel and allow flexibility over when and how card information is displayed. 8. [FBD] This command turns feedback delay on or off. It is necessary when installing some newer cards in older systems. -
Page 14: Card Control
Feedback Prefix Definitions: Card Model Number Firmware Revision Video Gain Levels Equalization Levels Example: Command = [EQ1=1C4] Feedback = (EQ0132C04) EQ = Equalization = Input 1 Equalization = Input 2 Equalization C04 = Card ID 12. [STA0] This command disables automatic feedback from the card and front panel. -
Page 15: Id Commands
16. [GAIN=] This command sets the gain level for an input to a value specified by the user. A gain setting of 4 is equivalent to unity gain. Command Format: [GAINm=xCn] = Input # (m = 1 or 2) = Gain level (m = # from 1 to 11, 4 = unity) Cn = Card ID (n = slot # from 1 to max slots) Example: Set the gain level for Input 2 of C4 to a value of... -
Page 16: Group Commands
20. [SID+] This command sets the card ID of all cards in a system to their slot number plus the offset value. Command Format: [SID+n] n = Offset amount (n = # from 0 to 99) The maximum card ID is 99, so subtract the highest slot number from 99 to find the maximum offset. -
Page 17: Summary Of Commands
24. [RMG] This command deletes one or all groups. Command Format: [RMGk] Gk = Group ID (k = # from 1-8, * for all) Example: Remove all cards from G52 by sending [RMG5]. The system will return the following feedback: [G5=0] Example 2: Remove all cards from all groups, effectively... -
Page 18: Using Menu Mode
7.4 MENU MODE Menu Mode commands allow virtually the same functionality as programming commands. the programming commands in the previous sections, menu commands prompt the user to select from a list of available options. The system then responds based upon selections made by the user. - Page 19 7.4.4 MT115-111 MENUS Following are the menus available to the MT115-111. The first menu is the Main Menu only. The second listing is an expanded view of the card’s sub-menus. The expanded menu contains values that indicate the current setting or value of a parameter.
-
Page 20: Troubleshooting Guide
LED is still not on, see Cause 2. The card is not initialized. back on again. If one of the LEDs is still not on, please call ALTINEX at (714) 990-2300. The software gain is too high. Set the gain control to 4 using the RS-232 commands in Section 7.2. -
Page 21: No Display
Solution 2: Bypass the MT115-111 and TP transmitter and connect the output of the source directly to the monitor. If the display is good, then call ALTINEX at (714) 990-2300. If there is still no display, see Cause 3. Cause 3: Cable connections are incorrect.
Need help?
Do you have a question about the Dual Twisted Pair Receiver to Computer / Component Video + Audio MT115-111 and is the answer not in the manual?
Questions and answers