Table of Contents
Advertisement
20. NEVER
LEAVE TOOL RUNNING UNATTENDED.
TURN THE POWER OFF. Don't leave the tool until it
comes to a complete stop.
21. DON'T OVERREACH.
Keep proper footing and
balance at all times.
22. MAINTAIN TOOLS WITH CARE. Keep tools sharp
and clean for best and safest performance. Follow
instructions for lubricating and changing acoessories.
23. DO NOT use power tools in the presence of
flammable liquids or gases.
24. DO NOT operate the toot if you are under the
influence of any drugs, alcohol or medication that
could affect your ability to use the tool properly.
25. Dust generated from certain materials can be
hazardous to your health. Always operate the band
saw in a well-ventilated area and provide for proper
dust removal. Use dust collection systems whenever
possible.
SPECiFiC SAFETY INSTRUCTaONS
.
TO AVOID INJURY from unexpected movement, make
sure the saw is on a firm, level surface, properly
secured to prevent rocking. Make sure there is
adequate space for operating. Bolt the saw to a support
surface to prevent it from slipping, walking, or sliding
during operation.
2.
TURN the saw OFF and unplug the saw before
moving it.
3.
USE THE CORRECT size and style of blade.
4.
USE blades rated at 2700 FPM or greater.
5.
MAKE SURE the blade teeth point down and
towards the table.
6,
BLADE GUIDES, SUPPORT BEARINGS, AND
BLADE TENSION must be properly adjusted to avoid
accidental blade contact and to minimize blade
breakage. To maximize blade support, afways adjust
the upper blade guide and blade guard so that it is
1/8 inch above the workpiece.
7.
TABLE LOCK HANDLE should be tight.
8:
USE EXTRA CAUTION with large, very small or
awkward workpieces.
g_
USE EXTRA SUPPORTS to prevent workpieces
from sliding off the table top. Never use another person
in place of a table extension, or to provide additional
support for the workpiece,
10. WORKPIECES
must be secured so they don't twisL
rock, or slip while being cut.
1t. PLAN intricate and small work carefully to avoid
pinching the blade, Avoid awkward operation and
hand positions to prevent accidental contact with the
bJade.
12. SMALL PIECES should be secured with jigs or
fixtures. Do not hand hold pieces that are so small
your fingers are under the blade guard.
13. SUPPORT round work properly (with a V-block or
clamped to the miter gauge) to prevent it from rolling
and the blade from biting.
14. CUT only one workpiece at a time. Make sure the
table is clear of everything except the workpiece and
its guides before you turn the saw on.
15. ALWAYS WATCH the saw run before each use. If
there is excessive vibration or unusual noise, stop
immediately. Turn the saw off. Unplug it immediately.
Do not start the saw again until the problem has
been located and corrected.
16. TO FREE any jammed material, turn the switch OFR
Remove the switch key and unplug the saw. Wait for
all moving parts to stop before removing jammed
material.
17. DON'T LEAVE the work area until all moving parts
are stopped. To childproof the workshop, shut off the
power to master switches and remove the switch key
from the band saw. Store it in a safe place, away
from children.
For your own safety, read the entire instruction manual
before operating the band saw.
1. Wear eye protection.
2. Do not wear gtoves, necktie, or loose clothing.
3. Make sure the saw is on a firm level surface and
properly secured.
4. USE ONLY THE RECOMMENDED ACCESSORIES.
5. Use extra caution with very large, very small, or
awkward workpieces.
6. Keep hands away from the blade at all times to
prevent accidental injury.
ELECTRnCAL
REQUBREMENTS
POWER SUPPLY AND MOTOR SPECIFICATIONS
To avoid electrical hazards, fire hazards, or damage to the
tool, use proper circuit protection. Use a separate electrical
circuit for your tools.Your saw is wired at the factory for
120V operation. Connect to a 120V, t5 Amp circuit and use
a 15 Amp time delay fuse or circuit breaker. To avoid shock or
fire, if power cord is worn or cut, or damaged in any way,
have it replaced immediately.
SAVE THESE mNSTRUCTIONS
GROUNDING
INSTRUCTIONS
This tool must be grounded while in use to protect the
operator from electrical shock,
tN THE EVENT OF A MALFUNCTION OR BREAKDOWN,
grounding provides a path of least resistance for electric
current and reduces the risk of electric shock. This tool is
equipped with an electric cord that has an equipment
grounding conductor and a grounding plug. The plug
MUST be plugged into a matching receptacle that is
properly installed and grounded in accordance with ALL
local codes and ordinances.
DO NOT MODIFY'THE PLUG PROVIDED. If it wilt not fit the
receptacle, have the proper receptacle installed by a
qualified electrician.
IMPROPER CONNECTION
of the equipment grounding
conductor can result in risk of electric shock. The
conductor with the green insulation (with or without yellow
stripes) is the equipment grounding conductor. If repair or
replacement of the electric cord or plug is necessary, DO
NOT connect the equipment grounding conductor to a live
terminal.
CHECK with a qualified electrician or service person if you
do not completely understand the grounding instructions, or if
you are not sure the tool is properly grounded.
USE ONLY 3-wire extension
cords that have 3-prong
grounding
plugs and 3-pole receptacles
that accept the
tool's plug. Repair or replace damaged
or worn cord
immediately.
Use a separate electrical circuit for your tools. This circuit
must not be less than #12 wire and should be protected
with a 15 Amp time lag fuse. Before connecting the motor to
the power fine, make sure the switch is in the OFF
position and the electric current is rated the same as the
current stamped on the motor nameplate. Running at a
lower voltage will damage the motor.
Fig. A
3-Prong Plug
I__
Grounding
Prong
Properly Grounded
3-Prong Receptacle
GUIDEUNES
FOR EXTENSION
CORDS
USE PROPER EXTENSION CORD. Make sure your
extension cord is in good condition, When using an
extension cord, be sure to use one heavy enough to carry
the current your product will draw. An undersized cord will
result in a drop in line voltage and in loss of power which will
cause the tool to overheat. The table below shows the
correct size to use depending on cord length and
nameplate ampere rating. If in doubt, use the next heavier
gauge. The smaller the gauge number, the heavier the cord,
Be sure your extension
cord is properly
wired and in
good condition. Always replace a damaged extension cord
or have it repaired by a qualified person before using it.
Protect your extension cords from sharp objects, excessive
heat and damp or wet areas.
(when using 120 volts only)
Ampere Rating
mo_e
tha¢_
not
more
thaf_
0
6
6
10
10
12
12
16
Totallength
of cord in feet
25'
50'
100'
150'
18
16
16
14
18
16
14
12
16
16
14
12
14
12
Not recommended
This band saw is for indoor use only. Do not expose to rain
or use in damp locations.
This tool is intended for use on a circuit that has a
receptacle like the one illustrated in FIGURE A.
FIGURE A shows a 3-prong electrical plug and receptacle
that has a grounding conductor. If a properly grounded
receptacle is not available, an adapter (FIGURE B) can be
used to temporariIy connect this plug to a 2-contact
ungrounded receptacle. The temporary adapter shoutd be
used only until a properly grounded receptacle can be
installed by a qualified technician. The adapter (FIGURE B)
has a rigid lug extending from it that MUST be connected
to a permanent earth ground, such as a properly
grounded receptacle box. The Canadian Electrical Code
prohibits the use of adapters.
CAUTION: In all cases, make certain the receptacle is
properly grounded, If you are not sure have a qualified
electrician check the receptacle.
Fig. 13 Grounding Lug _-_
(_-_ /
_L
Make
Sure This
_[_-_F_.-T-_ i
is Connected to a
_ ',_,-
_"
"_"t,_ Known Ground
_-4_
_t_l _
_---.-
I]_" 2-Prong
j% 'f_-'_y_
-
_N '_--._
Receptacle
_<-"_--
Adapter
SAVE THESE
iNSTRUCTiONS
5
Hide quick links:
Advertisement
Table of Contents
