Download Print this page

Troubleshooting - Craftsman 113.228162 Owner's Manual

12-inch wooo-turning lathe
Hide thumbs

Advertisement

Sears recommends the following
accessories
ITEM
CAT.
NO.
ITEM
CAT,
NO.
Work Bench ..........................................
See Catalog
Motor Pulley (Four Step) 1/2" Bore ......... See Catalog
Motor Pulley (Four Step) 5/8" Bore .......... See Catalog
Drill Chuck 1/2" Capacity with
No. 1 MT. Shank ..............................
See Catalog
Screw Center with No. 1 M.T. Shank ....... See Catalog
Ball Bearing Center with
No. 1 M.T. Shank ...............................
See Catalog
60° Center with No. 1 M.T. Shank ........... See Catalog
Face Plate, 4" Dia. with 3/4"-!6 Thread
9 holes ......................................................
9-2489
9" Dia. Sanding Disc only with 3/4"-16
Thread ....................................................
9-24906
Sanding Table .............................................
9-24922
Turning Tools ........................................
See Catalog
Draw Bolt with 1/4"-20 Threads ...............
See Catalog
Power Tool Know How Handbook ................. 9-29117
Bowl Turning Tool Rest ................................
9-24903
Face Plate 6" with 3/4"-16 Thread
6 holes ....................................................
9-24904
Copy Crafter ................................................
9-24907
Speed Reducer .....................................
See Catalog
Face Plate 4" dia. with 3/4"-16 Thread
Cast Iron, 6 holes ...............................
See Catalog
Diameter Sizing Gauge .................................
9-24909
Sears may recommend other accessories not listed in
the manual.
See your nearest Sears store or catalog
department for other accessories.
Do not use any
accessory unless you have received and read com-
plete instructions for its use.
trouble
shooting
WARNING:
FOR YOUR
OWN SAFETY,
TURN SWITCH
"'OFF"
AND
REMOVE
PLUG FROM
POWER
SOURCE
OUTLET
BE-
FORE TROUBLE
SHOOTING.
TROUBLESHOOTING
CHART
TROUBLE
Motor
will not run.
PROBABLE
CAUSE
1. Defective
On-Off
switch,
Defective
switch
cord.
Defective
switch
box receptacle.
2, Motor
protector
Open,
(only
if your
motor
is
equipped
with
an
overload
protector).
3, Burned
out motor
REMEDY
1, Replace defective
parts before
using Lathe
again.
2, Reset protector
when motor
has cooled,
3. Consult
Sears Service.
Any attempt
to repair this
motor
may create
a HAZARD
unless repair
is
done
by a qualified
service technician.
Repair
service
is available
at your
nearest Sears Store,
Lathe slows
down
1, V-belt
too loose
1. Adjust
belt tension,
see Assembly
Section.
when turning
Tailstock
rocks
I, Brass adjusting
screw is too
I. Adjust
screw. See Section,
"Getting
To Know
back and forth
loose.
Your
Lathe".
excessively.
Headstock
loose
1. Setscrew
not tight,
l, Tighten
setscrew.
See Section,
"Getting
To
on bed,
Know
Your
Lathe",
Wood burns
at
1, Cup center
too tight
or not
!. Back off tailstock
ran, and iubricate
taiistock
end.
lubricated,
cup center.
See Basic Lathe
Operation
Section,
"Spindte
Turr_ing,"
31

Hide quick links:

Advertisement

loading

  Related Manuals for Craftsman 113.228162

  Related Content for Craftsman 113.228162