Page of 15

Advertising

Owner'sManual
Power-Mat_
Power Nozzle
Model, Modelo, Mod61e
KC50XBZRZU01
KC50XBZTZU01
KC50XCMWZU01
CAUTION:
Read and follow all
safety and operating
instructionsbefore first
use of this product.
Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.
www.sears.com
Sears Canada, Inc.,Toronto, M5B 2B8
www.sears.ca
Part No. C_1ZCNTI3(30QO-KCI_1ZCNTZQ(_O
Printed in U.S.A.

   Also See for Kenmore Power-Mate KC50XBZRZU01

   Related Manuals for Kenmore Power-Mate KC50XBZRZU01

   Summary of Contents for Kenmore Power-Mate KC50XBZRZU01

  • Page 1

    Owner'sManual Power-Mat_ Power Nozzle Model, Modelo, Mod61e KC50XBZRZU01 KC50XBZTZU01 KC50XCMWZU01 CAUTION: Read and follow all safety and operating instructionsbefore first use of this product. Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A. www.sears.com Sears Canada, Inc.,Toronto, M5B 2B8 www.sears.ca Printed in U.S.A.

  • Page 2

    Attachment Use Chart ....Performance Features ....Please read this guide. It will help you assemble and operate your new Kenmore vacuum in the safest and most effective way, For more information about vacuum cleaner care and operation, call your nearest Sears store, You will need the complete model and serial numbers when requesting information.

  • Page 3

    Your safety is important to us. To reduce the risk of fire electr ca shock injury to persons or damage when usinq your vacuum cleaner, follow bas c safely precautions including the following: Read all intstructionsin this manual before Turn off all controls before unplugging. assembling or using your vacuum cleaner.

  • Page 4

    It is important to know your vacuum cleaner's parts and features to ensure its proper and safe use. Review these before using your cleaner. Item Part No. Part No. In U.S. In Canada : Headlight Bulb 20-5240 596181 Belt 20-5218 20-5218C Belt Wand Quick...

  • Page 5

    To remove: Step on Electrical Shock Hazard wand quick DO NOT plug into electrical supply release until assembly is complete, Failure pedal, then to do so could result in electrical pull up on shock or injury. wands. Release 1, Insert wand(s) into Power-Mate_ untilthe wand buttons snap into place, CAUTION Indicator...

  • Page 6

    Suggested sweeping pattern. CAUTION For best cleaning action, the Power-Mate ® should be pushed straight away from you Product Damage Hazard and pulled straight back. At the end of each Use care if the Power-Mate ® and pull stroke, the direction of the Power-Mate ® wand is left in the upright position as should be changed to point into the next it may tip over easily.

  • Page 7

    2. Press wand quick CAUTION Wand release pedal with foot ,Quick DO NOT attach or remove handle or and pull the wands Release wands while cleaner is ON. This straight ul Pedal Power-Mate s. could cause sparking and damage the electrical contacts.

  • Page 8

    EDGE CLEANER DIRT SENSOR (SOME MODELS) Active brush edge cleaners are on both The dirt sensor light system is mounted on sides of the Power- the Power-Mate" nozzle near the reset but- Mate ® . Guide either ton. It consists of a series of two red lights side of the Power- and two green lights.

  • Page 9

    2. As indicated by the illustration, the two dirt Although the dirt sensor feature in your sensor elements are located on the inside of Kenmore Power-Mate ®is designed for years the swivel, approximately 31,_inches/90 mm of trouble free use, the passage of dirt...

  • Page 10

    TO CLEAN AGITATOR: TO REMOVE BELT NOTE: In order to keep cleaning efficiency 1. Turn Power- high and to prevent damage to your vacu- Mate ® upside um, the aaitator must be cleaned every time down. the belt is changed. 2.

  • Page 11

    TO REPLACE BELT 4. NOTE: On dirt sensor models be sure that the board is upright and the wires are tucked back as shown. 1. Install new belt over motor drive, then over Motor Drive brush sprocket. Sprocket Agitator End Cap NOTE: See PARTS AND FEATURES for belt number.

  • Page 12

    TO REPLACE AGITATOR ASSEMBLY 1. Remove Power-Mate ®cover, belt and Electrical Shock Or Personal Injury agitator assembly. See =To Remove Belt" in Hazard BELT CHANGING AND AGITATOR Disconnect electrical supply before CLEANING. servicing or cleaning the unit. Failure to do so could result in elec- 2.

  • Page 13

    Review this chart to find do-it-yourself solutions for minor performance problems. service needed, other than those described in this owner's manual, should be performed by an authorized service representative. 1. Pawer-Mate"o0rmedinns Power-Mate" will not 1. Rug kl firmly. run when attached. unplugged.

  • Page 15

    Your Home For repair - in your home - of all major brand appliances, lawn and garden equipment, or heating and coolingsystems, no matter who made it, no maRer who sold it! For the replacement parts, accessories and owner's manuals that you need to do-it-yourself. For Sears professional installationof home appliances and items like garage door openers and water heaters.

Comments to this Manuals

Symbols: 0
Latest comments: