Download Print this page

JVC drvn KS-AX3101D Instructions Manual

Power amplifier.
Hide thumbs
   

Advertisement

KS-AX3104
KS-AX3102
KS-AX3101D
POWER AMPLIFIER: INSTRUCTIONS
LVT2205-001A
[K/US]
УСИЛИТЕЛЬ МОЩНОСТИ: ИНСТРУКЦИИ ПО ЭКСПЛУАТАЦИИ
ENGLISH
Thank you for purchasing a JVC product.
If you have any questions or require information regarding installation kits, consult your "JVC IN-
CAR ENTERTAINMENT" or a company supplying the kits.
For safety....
• Stop the car before performing any complicated operations.
CAUTIONS AND NOTES
This unit is designed to operate on 12 V DC, NEGATIVE ground electrical systems.
JVC recommends consulting a qualifi ed technician for installation.
• This unit uses BTL (Balanced Transformerless) amplifi er circuitry, i.e., fl oating ground system,
so comply with the following:
– Do not connect the "·" terminals of the speakers to each other.
– Do not connect the "·" terminals of the speakers to the metal body or chassis.
• Cover the unused leads with insulating tape to prevent them from short circuiting.
• When an extension lead is used, it should be as thick and short as possible; connect it fi rmly
with insulating tape.
• Be sure to leave an appropriate space between the antenna (aerial) and the wires of this unit.
• If the fuse blows, fi rst make sure the wires aren't touching to cause a short circuit then replace
the old fuse with one with the same rating.
• Do not let pebbles, sand or metallic objects get inside the unit.
• To keep the heat dissipation mechanism running effectively, wipe the accumulated dust off
periodically.
• Listening to the tape, radio, CD or digital audio player, etc. with the volume set at a high level
for a long period of time will exhaust the battery, while the engine is turned off or while the
engine is idling.
• This unit becomes very hot. Be careful not to touch the unit not only when using but after using.
DO NOT disassemble the unit since there are no user serviceable parts inside.
INSTALLATION
The following illustration shows a typical installation. However, you should make adjustments
corresponding to your specifi c car.
Å
Location of the unit
Onto the trunk floor
Under the front seat
ı
Install the unit
Provided screw
φ 4 × 20 mm (
13
/
in.)
16
Drilled hole
SAFETY INSTRUCTIONS
"SOME DOS AND DON'TS ON THE SAFE USE OF EQUIPMENT"
This equipment has been designed and manufactured to meet international safety standards but, like any electrical
equipment, care must be taken if you are to obtain the best results and safety is to be assured.
DO read the operating instructions before you attempt to use the equipment.
DO ensure that all electrical connections (including the mains plug, extension leads and interconnections between
pieces of equipment) are properly made and in accordance with the manufacturer's instructions. Switch off and
withdraw the mains plug when making or changing connections.
DO consult your dealer if you are ever in doubt about the installation, operation or safety of your equipment.
DO be careful with glass panels or doors on equipment.
DON'T continue to operate the equipment if you are in any doubt about it working normally, or if it is damaged in any
way–switch off, withdraw the mains plug and consult your dealer.
DON'T remove any fixed cover as this may expose dangerous voltages.
DON'T leave equipment switched on when it is unattended unless it is specifically stated that it is designed for
unattended operation or has a standby mode. Switch off using the switch on the equipment and make sure that your
family know how to do this. Special arrangements may need to be made for infirm or handicapped people.
DON'T use equipment such as personal stereos or radios so that you are distracted from the requirements of traffic
safety. It is illegal to watch television whilst driving.
DON'T listen to headphones at high volume as such use can permanently damage your hearing.
DON'T obstruct the ventilation of the equipment, for example with curtains or soft furnishings. Overheating will cause
damage and shorten the life of the equipment.
DON'T use makeshift stands and NEVER fix legs with wood screws–to ensure complete safety always fit the
manufacturer's approved stand or legs with the fixings provided according to the instructions.
DON'T allow electrical equipment to be exposed to rain or moisture.
ABOVE ALL
— NEVER let anyone, especially children, push anything into holes, slots or any other opening in the case — this could
result in a fatal electrical shock.
— NEVER guess or take chances with electrical equipment of any kind–it is better to be safe than sorry!
• Mount this unit on a firm surface, such as in the
trunk or under the front seat.
• Since heat is generated in the unit, do not
mount it near inflammable objects. In addition,
mount it in an area that will not prevent the unit
from dissipating the heat.
• Do not mount the unit in the places subject to
heat: near a radiator, in a glove compartment or
in insulated areas such as under a car mat that
will prevent the unit from dissipating heat.
• When mounting the unit under the front seat,
make sure that adjusting the seat position will
not catch any wire of the unit.
• When mounting this unit, be sure to use the
provided screws.
• If any other screws are used, there is a risk of
loosening the unit or damaging the parts under
the car floor.
• Before drilling holes in the trunk to install the
unit, make sure that there is a sufficient space
under the trunk so that you do not drill holes in
the fuel tank, etc.
POWER SUPPLY
KS-AX3104
KS-AX3102
KS-AX3101D
Fuse*
Car battery
Caution
To prevent short circuits while making connections, keep the battery's negative terminal
disconnected.
• When using a power cord (purchased separately), be sure to place the fuse near the battery as
shown.
• Connect the lead wire (power cord) through which power is supplied directly to the battery's
"ª" terminal only after all the other connections have been made.
The proper lead wire connected to each POWER terminal is as follows.
• + B and GND: AWG 8 to AWG 4 (The cross section is about 8 mm
• REM: AWG 18 to AWG 8 (The cross section is about 0.8 mm
a When you use JVC car receiver with a remote lead, connect to the REM terminal on this unit.
b When you connect a unit without a remote lead, connect to the accessory circuit of the car
which is activated by the ignition switch. In this case, noise may occur when the car receiver
is turned on or off. To avoid this noise, do not turn on or off the car receiver itself. You can
turn on or off the car receiver along with the on/off operation of the ignition switch.
TERMINAL CONNECTIONS
When making terminal connections, properly fi x each terminal with the provided screw by turning
it as illustrated.
• Use ring terminals (not provided) for secure connection.
Notes
• Make sure the screw is fixed in place to prevent disconnections.
• Avoid over-tightening as it may cause the damage to the screw or its
head slot.
SPEAKER SYSTEMS
Notes
• Be sure not to connect the "·" terminals of the speakers to a common point.
• If the same lead is used for both left/right or front/rear speaker wirings, this unit cannot be used.
Always use the independent leads for each speaker. In this case, redo the wirings.
• Use the speakers with an impedance of 2 Ω to 8 Ω (4 Ω to 8 Ω: when used in Bridge Mode).
• Use the speakers which have sufficient capacity to the unit.
The proper lead connected to each SPEAKER OUTPUT terminal is as follows.
KS-AX3104/KS-AX3102: AWG 18 to AWG 12 (The cross section is about 0.8 mm
KS-AX3101D: AWG 18 to AWG 8 (The cross section is about 0.8 mm
Dear Customer,
This apparatus is in conformance with the valid European directives and
standards regarding electromagnetic compatibility and electrical safety.
European representative of Victor Company of Japan, Limited is:
JVC Technical Services Europe GmbH
Postfach 10 05 04
61145 Friedberg
Germany
Information for Users on Disposal of Old Equipment and Batteries
[European Union only]
These symbols indicate that the product and the battery with this symbol should
not be disposed as general household waste at its end-of-life.
If you wish to dispose of this product and the battery, please do so in accordance
with applicable national legislation or other rules in your country and municipality.
Products
By disposing of this product correctly, you will help to conserve natural resources
and will help prevent potential negative effects on the environment and human
health.
Notice:
The sign Pb below the symbol for batteries indicates that this battery contains lead.
Battery
E43486-340B
1
For Customer Use:
Enter below the Model No. and Serial No. which
are located on the top or bottom of the cabinet.
Retain this information for future reference.
Model No.
Serial No.
1110NYMMDWTKK
EN, RU
© 2011 Victor Company of Japan, Limited
To metallic body or chassis
(To an accessory terminal)
Remote turn-on line
Ignition switch
2
to 8 mm
* Not Supplied
JVC car receiver, etc.
2
to 21 mm
2
.)
2
.)
2
to 3.3 mm
2
).
2
to 8 mm
2
).

Advertisement

   Also See for JVC drvn KS-AX3101D

   Related Manuals for JVC drvn KS-AX3101D

   Summary of Contents for JVC drvn KS-AX3101D

  • Page 1

    • REM: AWG 18 to AWG 8 (The cross section is about 0.8 mm to 8 mm a When you use JVC car receiver with a remote lead, connect to the REM terminal on this unit. INSTALLATION b When you connect a unit without a remote lead, connect to the accessory circuit of the car The following illustration shows a typical installation.

  • Page 2: Speaker Connections

    • Use the speakers with an impedance of 2 Ω to 8 Ω. Notes Å JVC car receiver, etc. • Securely connect all the parts. If the connections are loose, due to contact resistance etc., heat ı Speaker input connector.

  • Page 3: Troubleshooting

    KS-AX3104 • Use the speakers with an impedance of 2 Ω to 8 Ω. • Incoming signals from INPUT jacks are emitted through the PRE OUT jacks. Å INPUT JVC car receiver, etc. CROSSOVER HIGH INPUT HIGH INPUT CROSSOVER MONO...

  • Page 4

    В целях безопасности…. · · Внимание ª Å Примечания ı Примечания · φ Ω Ω Ω Ω...

  • Page 5

    Ω Ω Примечания Å ı Å ı CROSSOVER INPUT HIGH INPUT LEVEL MONO Ω Ω Пример: Å RECEIVER ı Ω Ω CROSSOVER INPUT HIGH INPUT Å LEVEL FRONT MONO REAR Ω Ω Å ı INPUT CROSSOVER HIGH INPUT HIGH INPUT CROSSOVER MONO MONO...

  • Page 6

    Ω Ω Å INPUT CROSSOVER HIGH INPUT HIGH INPUT CROSSOVER MONO MONO LEVEL LEVEL POWER ı PRE OUT INPUT HIGH INPUT CROSSOVER MONO LEVEL LEVEL BASS BOOST POWER POWER 50Hz 200Hz PRE OUT INPUT HIGH INPUT Å MONO ı Ω Ω...

This manual also for:

Drvn ks-ax3104, Drvn ks-ax3102

Comments to this Manuals

Symbols: 0
Latest comments: