Vehicle security system with seperate lock/unlock buttons (28 pages)
Summary of Contents for Scytek electronic Galaxy 2000RS-2W-DBP
Page 1
GALAXY 5000RS/2000RS SERIES-DBP D A T A B U S P O R T VEHICLE SECURITY SYSTEM WITH REMOTE START PRODUCT MANUAL...
Page 2
Limited Lifetime Warranty This vehicle security system is warranted to the original purchaser, to be free from defects in material and workmanship. The manufacturer will repair or replace at its option, and free of charge for the first twelve (12) months, any part that proves defective in material or workmanship under normal installation, use, and service, provided the product is returned to the manufacturer freight prepaid.
About Your System The ScyTek Galaxy 5000RS-DBP Series is a Combination Vehicle Security and Remote Starting System , Galaxy 2000RS-DBP Series is a Remote Starting with keyless entry. featuring a built-in "ScyNet Network Port" that allows direct connection of optional accessory modules and a PC interface offering expanded system operation.
Remote Transmitters Standard Remote Transmitter Description Button 2 Button 1 Button 1 Button 2 Button 5 Button 3 Button 3 Button 4 Button 4 Button 5 T5-SP Depending on the model chosen, the Galaxy 5000RS-DBP Series will be supplied with one or two T5 or T5-SP 5-button Remote Transmitters that are used to control the system’s operations.
Adding/Replacing Standard Remote Transmitters To replace lost or stolen transmitters or to add additional transmitters into the system, have all desired transmitters ready and follow the steps below. Note: Up to 4 one-way transmitters can be programmed to operate the system. Any previously stored transmitter will be erased if it is not programed within the following sequence To program the transmitter(s): 1.
2-way LCD Remote Transmitter Description Button 1 Button 2 Button 3 Button 4 Button 5 Depending on the model chosen, the Galaxy 5000RS-DBP-2W Series will be supplied with one or two 2-way LCD Remote Transmitters, offering increased range and confirmation of any activated features. Page 1 Button 1 Arms and Locks the system and when held for 5 seconds, activates the system’s Panic feature.
3. Press and release Button 1 on the first transmitter then on the second transmitter. · The siren/horn will chirp/honk once for every transmitter learned. 4. Turn off the ignition key. 5. The siren/horn will chirp/honk 3 times to indicate the system has exited programming mode. LCD Transmitter Battery Replacement Your Galaxy Remote Transmitter uses a 1.5 volt AAA alkaline battery, which will require replacement in time.
To set the daily start feature: 1. Press and hold Buttons 2 and 3 until the remote beeps four times. · The fan and clock will be shown indicating daily start mode is entered. 2. Press Button 2 until the desired hour is displayed. 3.
Page 11
CHP Set the siren/horn confirmation chirps/honks ON or OFF: 1. Press and hold Button 5 until the display shows CHP. ·The transmitter will beep three times. 2. Release Button 5. · The transmitter will beep once. · The LCD panel will show a siren if the chirps*/honks are enabled or "off" if the chirps*/honks are disabled.
Page 13
time date/engine run timer 11/16 3:10P Button 3 Button 4 Button 5 wakeup Button 1 Battery autostart alarm Button 2 status enabled enabled Optional 2-way Color remote transmitter is offering increased range and confirmation of any activated feature. Page 1 Button 1 Arms and Locks* the system and when held for 3 seconds, activates the system’s Panic feature.
Page 14
PAGER PARAMETERS SETTING Press and hold Buttons 2 and 3 until pager program features are displayed. Select pager setting by pressing buttons 1 or 2 to highlight the pager. Press button 3 to select the pager. Setting Date & Time Select Time Date setting by pressing buttons 1 or 2 to highlight the feature.
Page 15
Use buttons 1 & 2 to highlight the time parameter you wish to change, use buttons 3 & 4 to scroll up or down to chage the time. Save the changes by pressing button 5. START SET AUTO ST ON TIME: 08:00A Setting Alarm Clock Select Alarm setting by pressing buttons 1 or 2 to highlight the feature.
Page 16
Return to Previous Screen Select Previous Screen by pressing buttons 1 or 2 to highlight the feature. Press button 3 to select it. TIME DATE START TIME ALARM CLOCK SOUND ON BACK Press and hold Buttons 2 and 3 until pager program features are displayed. Select system setting by pressing buttons 1 or 2 to highlight the pager.
Page 17
Setting AutoStart Cold Temperature Threshold Select Cold Temp start setting by pressing buttons 1 or 2 to highlight the feature. Press button 3 to select SIREN CHIRP PASSIVE ARM COLD TEMP HOT TEMP BACK Use buttons 3 & 4 to scroll up or down to chage the temperature threshold. Save the changes by pressing button 5.
Page 18
Synchronize System and Pager Clocks Select Clock Sync setting by pressing buttons 1 or 2 to highlight the pager. Press button 3 to select the pager. Pager Clock Sync This feature synchronizes the pager clock to the security system time of a day clock. Select Pager Clock Sync by pressing buttons 1 or 2 to highlight the feature.
Page 19
START 1 SET SET TIME TIME: 8:00A Use buttons 1 & 2 to highlight Set Time press button 3. AUTOSTART 1 TIME: 8:00A The security system responce. Start Time 2 This feature sets the system Autostart 2 time. Select Sytem Clock Sync by pressing buttons 1 or 2 to highlight the feature. Press button 3 to select it. PGR CLK SYNC SYS CLK SYNC START 1 TIME...
Page 20
Pressing and holding transmitter button 5 will scroll through several transmitter programmable options - TEMPERATURE, ENABLE COLD START, ENABLE HOT START, VALET MODE, ENABLE AUTOSTART 1, ENABLE AUTOSTART 2. TEMPERATURE Check the temperature inside the vehicle 1. Press and hold Button 5 until the display shows TEMPERATURE 2.
Page 21
ADDITIONAL FUNCTION Transmitter Lockout Press and hold buttons 2 & 4 simultanously for 3 seconds to lockout the transmitter against accidental transmission. Release Transmitter Lockout Press and hold buttons 2 & 4 simultanously for 3 seconds to release the transmitter from Lockout. Out of Range Report pager report if no responce from the unit.
Page 22
Time: time of day clock Date/Engine Run Timer: date, or engine run minute timer if remote start activated (20 min max). Battery Status: displays remaining battery life. Wakeup Alarm: displays Wakeup alarm enabled Autostart: Remote Start Autostart enabled Transmit: Pager transmission in progress time date/engine run timer 11/16...
System Operation Remote Arming/Locking The system monitors 5 independent areas ( zones ) while armed: doors, hood/ trunk, shock sensor, optional sensor input, and the network port for future expansion. To Arm and Lock the System: 1. Turn off the ignition. 2.
Tamper Alert If the system was triggered while away, the LED will flash to indicate which zone triggered the system after disarming and turning the ignition ON. The LED indication will repeat 8 times. LED Flashes (60 seconds): 1 flash optional sensor 2 flashes shock sensor...
Panic Mode In the event of an emergency, the transmitter’s remote Panic feature can be used to instantly trigger the alarm/panic feature. To activate the Panic Mode: 1. Press and hold Button 1 for five seconds. · The alarm will sound. ·...
3. Press the valet switch 4 times. · The siren will chirp each time the valet switch is pressed. 4. Within 5 seconds, press Button 3 on the transmitter. · The siren will chirp 3 times. 5. Press the valet switch the number of times equal to the desired code (from 1-15). 6.
Remote Start Features Remote Starting To Remote Start the System: 1. Be sure the system is not in Valet Mode. 2. Press and hold Button 4 for three seconds. · The parking lights will flash 4 times and turn on. ·...
Automatic Start Mode Automatic Start feature has three modes that will start the vehicle every one or two hours within a 24 hour period. 1. Timer Only Mode (factory default) The Automatic Start feature starts the vehicle automatically every one or two hours and runs for the preset Run Time.
Page 29
Manual Transmission Remote Start Features Model: Galaxy 5000RS-DBP-M 1- Tach wire must be connected , The system must learn RPM. 2- Hand brake must be connected. 3- Door trigger must be connected 4- Clutch override installed NOTE: MUST USE RELAY, SEE PAGE 26. Remote Starting With engine running and Hand-brake engaged put the vehicle transmission in neutral and remove the foot from the brake pedal, press the remote start button on your transmitter, parking lights will flash twice...
Extended Features Ignition Door Locking For added safety, the Ignition Door Locking feature allows vehicles equipped with power door lock systems to automatically lock the doors when the ignition is turned on. If a door is open when the ignition is turned on, the Ignition Door Locking feature is disabled to protect against locking the keys inside the vehicle.
System Installation 1. Thoroughly read and become familiar with the installation instructions before beginning the installation. 2. Review system contents: Main Unit 1 or 2 One-way 5 Button Remote Transmitters (varies by model) 1 or 2 Two-way 5 Button LCD Remote Transmitters (varies by model) Siren Shock Sensor Harnesses...
Mounting the Control Unit The control unit must only be mounted in the interior of the vehicle. Do not mount the main unit in the engine compartment. Choose a mounting location that will not be easily accessible to a thief, and will not interfere with the operation of any vehicle components such as foot pedals, steering column, air vents, seat rails, etc.
System Wiring 6-Pin Starter Harness Pin 1 RED WIRE A: Main Power Input A (+). Connect to the battery or constant power wire at the ignition switch with a minimum 25 Amp supply. Remove the fuse until the installation is complete and all wiring is checked.
Pin 11 VIOLET WIRE: Positive Door Input (+). Connect to the door switch circuit wire that shows +12V when the door is open. This type of door circuit is usually found on Ford vehicles. Pin 12 GREEN WIRE: Negative Door Input (-). Connect to the door switch circuit wire that shows ground when the door is open.
2-Pin White Connector: Located on the side of the main module. · Green WIRE - Parking Brake Input (-) For Manual Transmission and/or vehicles equipped with a turbo charged engine. Must be connected if using the Turbo Timer feature and/or Manual Transmission remote start feature. ·...
System Programming Entering System Programming This system is compatible with both the LCD two way transmitter or the standard transmitter, all system programming can be performed using either one. To enter System Programming: 1. Turn the ignition switch to the ON position. 2.
Page 37
Programming Branch Table Branch Feature Button 1 (default) Button 2 Button 3 1. Arm Mode Manual Arming Passive Arming 2. Auto Rearming Mode Disabled Enabled 3. Arming Chirps Siren Chirps On Siren & Horn Chirps On Silent 4. Ignition Door Locking Set Override Code 5.
Page 38
by programming the system for double unlock pulse. 7. Door Lock Pulse Length. Selects between a 1, 3 or 0.1 seconds output for door locking and unlocking. Program to 3 seconds for vehicles equipped with vacuum door locking systems. 8. Passive Door Locking. Selects whether or not the system will automatically lock the doors during Passive Arming and Auto Rearming mode.
Page 39
16. Auxiliary 3 Output Mode. Selects between Channel 3, Factory Rearm output, or third Ignition ouput. 17. Lock After Start. When selected, the doors will automatically lock after remote starting. Using button 3 disabled Mp Siren Mode. 18. Lock After Shutdown. When selected, the doors will automatically lock after remote shutdown. 19.
Page 40
28. Siren Mode. Selects standard siren (defualt) or MP Player Siren. 29. Turbo Timer. When enabled, if the emergency brake has been applied Ignition power will be kept On for a predetermined time (2 minutes Factory Default) from the application of the emergency brake. 30.
Door Lock Diagrams Follow the diagrams below for connecting basic door lock systems. For Two Stage door lock systems (separately unlocks driver and passenger doors) see following pages. Negative Trigger Positive Trigger blue green Reverse Polarity Vacuum Adding Actuators Page 38 - Galaxy 5000RS-DBP...
Two Stage Door Lock Diagrams The Galaxy 5000RS-DBP Series is equipped with a dedicated Passenger Unlock output allowing Two Stage Door Lock operation. When connected as shown below, disarming the system will unlock only the driver’s door. Pressing the disarm button again will unlock all doors. Two Stage Negative Trigger Two Stage Positive Trigger Door Lock Inverter Green Wire...
Page 44
Two Stage Door Lock Diagrams cont’d Two Stage Reverse Polarity Two Stage Adding Actuators Page 40 - Galaxy 5000RS-DBP...
Technical Information FCC ID: OARRXAM2000 This device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions: 1) This device may not cause harmful interference. 2) This device must accept any interference received, including interference that may cause undesired operation Built-in LED Light/Override/Valet/Call Switch into Antenna...
Page 46
Starter Diagnostics Starter doesn’t start and parking lights flash: 3 Times - Engine RPM not detected (check tach wire and/or perform tach learn procedure) Hood Trigger is active (hood is open, wire is shorted to ground or pin switch is defective) 4 Times - Brake Trigger is active ( Brake switch input is shorted to ground or incorrect) 5 Times - Unit is in Valet (service) mode, and start is disabled.
Wiring Diagram Galaxy 5000RS-DBP Series Green Lock output (-) 500mA Blue Unlock output (-) 500mA Shock Sensor Port Green/White Brake Input(+) Black/Gray Tachometer Input White/Red Auxiliary 2 Output (-)500mA LED Port Black/White Dome Light output (-)500mA (must use relay) Valet Switch Port Yellow Ignition Input (+) ( Must Be connected Blue/Yellow...