Zenith L26W56SA Installation And Operating Manual page 46

(Continued from previous page)
The value range is 0 to 63, with 63 as the default, which gives the
user the full range of volume control if item 008 MIN VOLUMEis
also set at O. Change values with ADJ Left/Right arrow keys. It may
be best to set the same value on every L26W56XA.
*Note: The maximum volume level cannot have a value setting lower
than the MIN VOLUMElevel (described previously).
O10 - MUTE DISABLE
EnabLesor disables sound mute function. If set to I, sound cannot
be muted, mute is disabled. If set to 0, sound can be muted.
01:1 - KEY DEFEAT(Keyboard Defeat)
If set to i, key defeat prevents the end user from accessing the on-
screen menus with the display front paneL--MENU, SELECT,and Left /
Right arrow keys and TV/AV do not function. If set to 0, those keys
do function.
*Note; The menus can always be accessed by pressing MENU on the
renlote.
015 - SLEEPTIMER
If set to 1, the SLEEPTIMER feature may be used. If set to 0, the
SLeep Timer is not available.
016 - EN TIMER (EnabLe On/Off Timers)
If set to 1, Timer function is avaiLabLe to user. Set to 0 to disable
On/Off limer functions. (CLock must be set in order to use limers.)
017 - ALARM
Gives the instaLLerthe option of making the ALarm function avaiLabLe
to the end user. If set to I, ALarm function is avaiLabLe to end user.
Set to 0 to disable the ALarm function.
*Note: Clock must be set before the Alarm function will work.
021 - V-CHIP (Parental Control)
Set to 1 to activate V-Chip (Parental ControL); have it available to
end user to filter and control or otherwise restrict programming
content that can appear. Set to 0 to turn V-Chip feature Off, not
avaiLabLe to user; no programming restrictions can be set.
022 - MAX BLK HRS (Maximum Block Hours)
Sets hours from 0 to 99 for the maximum V-Chip (Parental ControL)
block hours. Default setting is for 12 blocking hours.
023 - CAPTION LOCK
Set to 1 to restore previous caption Oni0FF state after turn OFF. If set
to 0, captions are always Off at turn On.
028 - CH. OVERIDE (Channel Override)
If set to 1, the user can select channeLs with either Channel
up/down or by direct keypad entry. If set to 0, only those channels
that are added on the channel List can be selected.
029 - OLD OCV (On Command Video
TM)
Set to i for operation with systems from On Command Corporation.
030 - ACK MASK
M.P.I. Communication Parameter. Leave at default setting unless
changed by Pay-Per-View provider. When set to 1, changes M.P.I. for
some 0CV boxes.
031 - POLL RATE
M.P.I. Communication Parameter. SeLects PoLLRate for M.P.I. Leave at
default setting unless changed by Pay-Per-View provider. Step size of
16 ms.
032 - TIMING PULSE
M.P.[. Communication Parameter. Leave at default setting unless
changed by Pay-Per-View provider. Sets baud rate. Step size of 4.3
uS.
034 - CAMPORTEN. (Camera Port Enable)
Set to 1 to enable Video 2 input on display paneL. If set to O, Video
2 input on display panel is not functionaL.
035 - COMPPORTEN. (Computer Port Enable)
Enable/disables display panel HDMI input jack. Set to 0 to disable,
set to 1 to enable.
*Note: The setting above is ignored if Installer item 093 RJP
AVAIL ABLE, is set to 1.
038 - YPrPb EN. (Rear Component Video Enable)
Set to 1 to enable display panel rear Component Video i input.
Set to 0 to disable display panel rear Component Video 1 input.
039 - REAR AUX EN. (Rear Aux Enable)
Set to I to enable display panel rear AUX (Video i) input.
Set to 0 to disable display panel rear AUX (Video I) input.
040 - AUTO CAMPORT
Set to 1 to automaticaLLy switch to Camport when equipment is
connected to front Video input.
Set to 0 to disable front Video automatic source selection.
*Note: This item must be set to 0 in order to enable item 093 RJP
AVAILABLE to be set to 1.
046 - STRT AUX SRCE (Start Aux Source)
Sets the starting AUX source.
Start source if start channel -0
1 = Videol 4 = RGB1 7 = Video 3 / S-Video
2 = Video2 5 = Component 2 255 = Last Aux
3 = HL)Mt i 6 = Component 1
047 - AUX STATUS
Set to 1 for M.P.I. AUX source to be reported as a channel number
instead of channel 0. Set to 0 to disable AUX identification change.
ControLs M.P.I. status channel response for AUX inputs.
PAG E 46