Table of Contents
Advertisement
Patent Pending
Model No. 831.159720
Serial No.
The serial number is found in the
location shown below. Write the
serial number in the space above.
Serial
Number
Decal
EXERCISE
EQ
u
t P
M
F---.NT
Jell
JR
I|
I
|el
_.
HELPLINE!
/-800-736-6879
USER'S MANUAL
SEARS, ROEBUCK AND CO.
HOFFMAN ESTATES, IL 60179
www.weid,.,rfitness.com
new products,
prizes,
fitness tips, and much more!
Advertisement
Table of Contents
Related Manuals for Weider PRO 9930
Summary of Contents for Weider PRO 9930
- Page 1 Patent Pending Model No. 831.159720 USER'S MANUAL Serial No. The serial number is found in the location shown below. Write the serial number in the space above. Serial Number Decal EXERCISE F---.NT Jell HELPLINE! /-800-736-6879 SEARS, ROEBUCK AND CO. HOFFMAN ESTATES, IL 60179 www.weid,.,rfitness.com new products, prizes,...
- Page 2 important Precautions ..............Before You Begin ..............Assembly ................Cable Diagrams ..............Adjustment ................Trouble-shooting and Maintenance ............Weight Resistance Chart .."............Ordering Replacement Parts ............Back Cover Full 90-day Warranty ............Back Cover Note: A PART LIST/EXPLODED DRAWING and a PART IDENTIFICATION CHART are attached in the center of this manual.
-
Page 4: Overview & Dimensions
HELPLINE at 1-800-736-6879, Monday through Thank you for selecting the innovative and versatile Saturday, 7 a.m. until 7 p.m. Central Time (excluding WELDER ° PRO 9930 Home Gym. The WELDER ° PRO holidays). To help us assist you, please note the prod- 9930 offers a unique selection of weight stations uct model number and serial number before calling. - Page 5 Note: This introduction will save you more time Identifying Parts than it takes to read itt To help you identify the small parts used in assem- bly, we have included a PART IDENTIFICATION CHART located in the center of this manual. Place the chart on the floor or work table and use it to quickly identify different parts for each step.
-
Page 6: Frame Assembly
Before beginning, make sure that you have read and understood the information on page 5. Locate and open the parts bag labeled "FRAME ASSEMBLY." Press a 2" Square Inner Cap (38) into the Butterfly Base (61). Press two 2" Square inner Caps (38) into the Press Base (60). - Page 7 " "3.-'Place _vo'_/e!ghi Burn'pers (8_ over'the indicated -" holes in the Butterfly Base (61). Slide the Weight Guides (58) into the indicated holes. Attach the Weight Guides (58) to the Butt_;iy Base (61) with two 3/8" x 2 1/2" Bolts (6), four 3/8" Flat Washers (17), and two 3/8"...
- Page 8 _._ Hold-the Butteflly -Top Frame-(64) and the Press Top Fr._r:ne(63)-on the indicated brab'kets on" the Uprights (59, 62) and the Weight Guides (58)• Note: Before attaching the Top Frames to the Uprights, make sure that both Weight Guides (58) are positioned inside of the indicated holes.
- Page 9 Locate and open the pg,,Is bag labeled "ARM ASSEMBLY." Lubricate See the inset drawing. Orient the Press Frame (53) as shown. Lubricate a 3/8" x 8" Bolt (30). Attach the Press Frame to the Press Base (60) with the 3/8" x 8" Bolt, two 1"...
- Page 10 _12. PreS's-two.1 1/2_' SqeaFe Irme_ Caps-(79) into the Eeg _ " Le_,er (49), - Insert a Bumper (33) between the brackets on the Leg Lever (49). Secure the Bumper to the Leg Lever with a #10 x 1" Screw (32). Slide the bracket on the Leg Lever (49) onto the Press Seat Frame (52).
- Page 11 15. Wrap the Short Cable over a "V" Pulley'(21) as _-, shown. Attach the "V" Pulley and a Long Cable Trap (14) to one side of the welded bracket on the Butterfly Upright (62) with a 3/8" x 2 1/2" Bolt (6) and a 3/8" Nylon Locknut (4).
- Page 12 _19. Wra{:):the Mediur_Cable (72)-over a 4 1/2" Pulley -. (34) in the c]irection shown. Atta'¢h the Pulley to the Butterfly Top Frame (64) with a 3/8" x 1 3/4" Bolt (22) and a 3/8" Nylon Locknut (4). 20. Attach the threaded shaft on the Medium Cable (72) to the Small "U"-Bracket (43) with a 1/4"...
- Page 13 -22._Wrap the'Long(_able'i73)'aro_nd a 3 t/2" Pulley (5) ..in the direction shown. Attach the Pulley and a Cable Trap (39) to the Butterfly Upright (62) with a 3/8" x 3 3/4" Bolt (7), a 3/8" Flat Washer (17) and a 3/8" Nylon Locknut (4).
- Page 14 *25. Notd:.For.clarity,:thisand_he following drawings 25 - ""~:" sh_w someparts removed, "; Remove the lower 3 1/2" Pulley (5) from the Double "U" Bracket (36). Then, wrap the Long Cable (73) over the Pulley (5) in the direction shown. Attach the Pulley to the Double "U"...
- Page 15 " 29-.'" wrap tl_e"Lon_) Cable" (73") around a:=V"-Pulley_21) ..in the direction shown. Attach the "V"-Pulley and a Large Cable Trap (14) to the small tube on the Press Seat Frame (52) with a 3/8" x 3 1/4" Bolt (28), a 3/8"...
- Page 16 ......o atA semb,y ......,#:_ ..........: ......m: m ............i!iiiiiiii!iiiiiiiiiiiiiii!ili::!ili!!iii_iiii!ii!i_iiii!iiiiiiiil iii!: ii!i_!ili:iriiii!i!iiiiiiiii!ili_ili_i!iii_i:_i_iii!ii;ili:i!ii!!iiiilililill 33. Locateandopenthepa:tsbaglabeled"SEAT ASSEMBLY." Insert a 1/4" x 2" Carriage Bolt (85) through the cen- ter hole in a Seat Plate (42). Attach the Seat Plate to a Seat (51) with two 1/4"...
- Page 17 " "36__nsert a :1/_, ';"x 1-1/2" (_'arfiage'Bolt (82) "througlTthe_ "-" center hole in a Seat Plate (42). Attach the Seat Plate to a Seat (51) with two 1/4" x 3/4" Screws (13). Insert the 1/4" x 1 1/2" Carriage Bolt (82) into the indi- cated hole in the Seat Bar (74) and secure it with a 1/4"...
- Page 18 1_9. Appl_,.{he WELDER PRO 992,0 decal in the location- 39" shown. "; WELDER PRO 9930 40. Make sure that all parts have been properly tightened. The use of the remaining parts will be explained in ADJUSTMENT, beginning on page 21 of this manual. Before using the home gym, pull each cable a few times to make sure that the cables move smoothly over the pulleys.
- Page 19 The Cable Diagrams below and on the next page show the proper routing of the Short Cable (71), the Medium Cable (72), and the Long Cable (73). The numbers show the correct route for each Cable. Make sure that the Cables are routed correctly, that the Pulleys move smoothly, and that the Cable Traps do not touch or...
- Page 20 ,--4 Long Cable; (73)
-
Page 21: Changing Weight Setting
The instructions below describe how each part of the home gym can be adjusted. Refer to the exercise poster accompanying this manual to see how the home gym should be set up for each exercise. IMPORTANT: When using an attachment, make sure it is in the correct starting position for the exercise to be performed. -
Page 22: Troubleshooting And Maintenance
Inspect and tighten all parts each time you use the home gym. Replace any worn parts immediately. home gym can be cleaned using a damp cloth and mild non-abrasive detergent. Do not use solvents. Tightening the Cables If a cable slips off the pulleys often, the cable may have become twisted. Remove the cable and re-install it. -
Page 23: Weight Resistance Chart
The threaded shaft on the Med urn'Cab e (72) attached to-. (3./ the Weights (8) can also be used to tighten the cables. _ - --72 To tighten the Medium Cable (72), remove the Small "U"- _i,-..---- Bracket (43) by removing the 5/16" Nylon Locknut (2) and the 5/16"... - Page 25 Key No. Qty. Description Key No. Qty. Description 5/16" x 2 1/2" Carriage Bolt Leg Lever 5116" Nylon Locknut Lat Bar 5/16" x 2 112" Bolt Seat 3/8" Nylon Locknut Press Seat Frame 3 1/2" Pulley Press Frame 3/8" x 2 1/2" Bolt Press Arm 3/8"...
- Page 26 -41--e ._- 40...
- Page 27 Thischartis provided tohelpyouidentifythesmall p artsusedin assembly. Thenumber i n parenthesis b elow eachpart refers to the key number of the part. Important: Some parts may have been pre-assembled shipping purposes. If you cannot find a part in the parts bags, check to see if it has been pre-assemblecl. Note: Assembly is divided into four stages: 1) frame assembly;...
- Page 28 1/4" Flat Washer (11) 5/16" x 1 3/4" Bolt (9) 5/16" x 2 1/2" Bolt (3) 5/16" Flat Washer (19) 5/16" x 2 3/4" Bolt (20) '1 3/8" Flat Washer (17) 114" Nylon Locknut (I 6) 1/4" x 2" Bolt (86) 5/16"...
- Page 29 _\\\\\\\\\\\_ _\\\\\\\\\\\\_ 1/4" x 1 1/2" Screw (88) 1/4" x 1 1/2" Carriage Bolt (82) 3/8" x 1" Belt (15) "V" Pulley (21) (Not shown to scale) 3/8" x 1 3/4" Bolt (22) 3 1/2" Pulley (5) (Not shown to scale) 3/8"...
- Page 30 3/4" Round Inner Cap (40) 1" x 7/8" Plastic Bushing (29) 1" Round Cap (26) 1" Round Inner Cap (41) 1" Inner Cap (80) 1 3/4" Square Inner Cap (37) 1 1/2" Square Inner Cap (79) 2" Square Inner Cap (38)
- Page 31 SmARs- The model number and senat number of your WELDER ® PRO Model No. 831.159720 9930 Home Gym are hsted on a decal attached to the frame See the front cover of th_s manual to find the Iocatron of the decal QUESTIONS? A_I replacement parts are ava=lable for tmmed_ate purchase or special order when you visit your nearest SEARS Service Center,...