Operating A Cable Box Or Dbs Receiver - Sony KP-41T65C Service Manual

MDP manufacturer code numbers
Manufacturer Code number
Sony 701
Kenwood 707
Magnavox 703
Maranz 702
Mitsubishi 702
Panasonic 704
Philips 703
Pioneer 702
RCA 702
Sanyo 706
Sharp 705
Yamaha 703
Notes
• If more than one code number is listed, try entering them one
by one, until you come to the correct code for your equipment.
• In some rare cases, you may not be able to operate your non-
Sony video equipment with the supplied remote control. This
is because your equipment may use a code that is not included
with this remote control. In this case, please use the
equipment's own remote control unit.
• The code numbers for Sony equipment are assigned at the
factory as follows:
VHS VCR 301 (preset code for the supplied
remote control)
8 mm VCR 302
Beta, ED Beta VCRs 303
• Whenever you remove the batteries — to replace them, for
example — if too much time is taken, the code number may
revert to the factory setting and must be reset.
36 -EN Operations
Operating video equipment
VTR (POWER)
VTR (FUNCTION)
Video operating
buttons
1 2 3
0 – 9 buttons
4 5 6
7 8 9
0 ENTER
CH +/–
Use the video operating buttons on the remote
control to operate the video equipment.
Press VTR (FUNCTION) before operating the
video equipment.
Operating a VCR Buttons on the remote control
To turn on or off Press VTR (POWER).
To select a channel Press the 0 – 9 buttons.
directly
To change channels Press CH +/–.
Press ( while pressing r. First release
To record
(, then release r.
To play Press (.
To stop Press p.
Press ).
To fast forward
Press 0.
To rewind the tape
Press P.
To pause
To resume normal playback, press again.
To search the picture Press ) or 0 during playback.
forward or backward To resume normal playback, release the
button.
To change input mode Press TV/VTR.
Operating an MDP Buttons on the remote control
To turn on or off Press VTR (POWER).
To play Press (.
Press p.
To stop
Press P.
To pause
To resume normal playback, press again.
To search the picture Keep pressing ) or 0 during
forward or backward playback.
To resume normal playback, release the
button.
To search the chapter Press CH +/–.
forward and backward
Note
• If the video equipment does not have a certain function, the
corresponding button on this remote control will not operate.
Operating a cable
box or DBS receiver
You can program the supplied remote control to
operate a cable box or DBS receiver. Follow the
procedures below to set the manufacturer's code
number in the remote control.
DBS/CABLE (POWER)
DBS/CABLE
(FUNCTION)
DISPLAY*
1 2 3
0 – 9 buttons
4 5 6
7 8 9
JUMP 0 ENTER
TV/DBS* GUIDE*
V/v/B/b/ *
MENU*
CH +/–
CODE SET
* The TV/DBS, GUIDE, DISPLAY, V/v/B/b/ , and MENU
buttons can be used only with a DBS receiver.
1
Turn off the equipment you want to set up,
and press DBS/CABLE (FUNCTION).
FUNCTION
DBS/CABLE
2
Press the CODE SET, DBS/CABLE (FUNCTION),
and 0 – 9 buttons to enter the
manufacturer's code number (see the chart
on the right column), then press ENTER. For
example, to program your remote control
to operate a Sony DBS receiver, press CODE
SET, DBS/CABLE (FUNCTION), 8, 0, 1, and
ENTER.
FUNCTION
ENTER
CODE SET DBS/CABLE
8 0 1
3
Press DBS/CABLE (POWER) to turn on the
cable box or DBS receiver.
DBS/CABLE
4
Use the cable box/DBS control buttons to
check if the code number works.
For example, to operate a cable box or DBS receiver,
you can use the DBS/CABLE (POWER), JUMP, CH
+/–, 0 – 9 and ENTER buttons.
Note
• If the cable box or DBS receiver does not have a certain
function, the corresponding button on this remote control will
not operate.
To operate the projection TV
Press TV (FUNCTION). Then use the projection TV
control buttons to control the projection TV.
For more details on operating the cable box or
DBS receiver
Refer to the operating instructions that come with the
equipment.
If the remote control doesn't work
• First, try repeating the setup procedures using the other codes
listed for your equipment.
Manufacturer code numbers (cable box)
Manufacturer Code number
Hamlin/Regal 222, 223, 224, 225, 226
201, 202, 203, 204, 205, 206, 207, 208,
Jerrold/G. I.
218
Oak 227, 228, 229
219, 220, 221
Panasonic
Pioneer 214, 215
209, 210, 211
Scientific Atlanta
Tocom 216, 217
Zenith 212, 213
Manufacturer code numbers (DBS receiver)
Manufacturer Code number
Sony 801 (preset code for the supplied
remote control)
RCA 802
Notes
• If more than one code number is listed, try entering them one
by one until you come to the correct code for your equipment.
• If you enter a new code number, the code number you
previously entered at that setting is erased.
• In some rare cases, your equipment may use a code that is not
provided with this remote control and you may not be able to
operate your equipment with the supplied remote control. In
this case, use the equipment's own remote control unit.
• Whenever you remove the batteries — to replace them, for
example — if too much time is taken, the code numbers may
revert to the factory setting and must be reset.
37 -EN
Operations
EN