Sears Craftsman 113.213850 Owner's Manual
  1. Manuals
  2. Brands
  3. Sears Manuals
  4. Power Tool
  5. Craftsman 113.213850
  6. Owner's manual
Sears Craftsman 113.213850 Owner's Manual

Sears Craftsman 113.213850 Owner's Manual

Motorized 15" floor model drill press
Hide thumbs
Table of Contents

Advertisement

Quick Links

SAVE THiS MANUAL
FOR FUTURE REFERENCE
MODEL NO.
113.213850
DRILL PRESS WiTH
112 HP MOTOR
Serial
Number
Model and serial
number
may be found
at the rear of the head.
You should
record both
model and serial number
in a safe place for
future use.
CAUTION:
Read GENERAL
and ADDiTiONAL
SAFETY
iNSTRUCTiONS
carefully
FLOOR
MOTORIZED
15 INCH
MODEL DRILL
• assembly
e operating
= repair parts
Sold by SEARS,
ROEBUCK
AND
CO., Chicago,
IL. 60684
U.S.A.
Part No. 71329
Form No. SP4738
PRESS
2/84

Advertisement

Table of Contents
loading

Related Manuals for Sears Craftsman 113.213850

Summary of Contents for Sears Craftsman 113.213850

  • Page 1 SAVE THiS MANUAL FOR FUTURE REFERENCE MODEL NO. 113.213850 DRILL PRESS WiTH 112 HP MOTOR Serial Number Model and serial number may be found at the rear of the head. MOTORIZED You should record both 15 INCH model and serial number in a safe place for FLOOR MODEL DRILL...
  • Page 2 FULL ONE YEAR WARRANTY ON CRAFTSMAN DRILL PRESS If within one year from the date of purchase, this Craftsman Drill Press fails due to a defect in material or workmanship, Sears will repair it, free of charge. WARRANTY SERVICE IS AVAILABLE BY SIMPLY CONTACTING...

  • Page 3: For Drill Presses

    other 2t. DIRECTION OF FEED part that is damaged should be careful- ly checked to ensure that it will operate pro- Feed work into a blade or cutter against perly perform intended function. direction of rotation of the blade or cutter Check for alignment of moving parts, binding only.
  • Page 4 additional safety instructions for dril! presses fixtures unusual operations 12.This Drill Press has 12 speeds listed adequately hold, guide and position work- below: piece for best quality and minimum hazard. 300 RPM 1450 RPM Never climb on the drill press Table. 375 RPM 1530 RPM Turn...
  • Page 5 TOOLS NEEDED UNPACKDNG AND CHECKnNG CONTENTS Model 113.213850 is shipped complete carton includes 1725 COIVlS_NA_ motor. Separate parts from packing materials check each one with "Table of Loose Parts" COMBINATION SQUARE MUST BE TRUE make certain items accounted for, STRAIGHT EDGE OF DRAW LIGHT BOARD 3/4"...
  • Page 6 motor specifications and electrical requirements MOTOR SPECIFICATIONS This power tool is equipped with a 3-conductor cord grounding type plug which This drill press is designed to use a 1725 RPM grounding prong, approved Underwriters' Laboratories and the Canadian Standards Associ- motor only.

  • Page 7: Set Screw Wrench

    assemb0y WARNING: FOR YOUR OWN SAFETY, NEVER COLUMN CONNECT PLUG TO POWER SOURCE OUTLET UNTIL ALL ASSEMBLY STEPS ARE COMPLET- SUPPORT ASSEMBLY OF COLUMN AND TABLE HARDWARE Position base on floor. Remove protective covering and discard. Remove protective sleeve from column tube and discard.
  • Page 8 assembly TABLE i i _ii_ !i_iii_i_ _ _i:i i Remove protective covering from table discard. Place table in support and tighten table lock (located under table) by hand. SUPPORT "J1 INSTALLING THE HEAD CAUTION: HEAD ASSEMBLY WEIGHS ABOUT 60 POUNDS. CAREFULLY LiFT HEAD.
  • Page 9 LEVER _HAFT Locate one (t) tension rod and one (1) knob among loose parts. BELT Screw the knob on the rod, then screw ENSION rod into the lever shaft. HANDLE POINTER Locate one (1) 10-32x3/8 pan hd. screw one (1) pointer among loose parts bag.
  • Page 10 assembly 3/16" ROD OR DRILL Insert a piece of 114" dia. STEEL ROD in to LOCKING one of the holes in the chuck body. ;OLLAR CHUCK Insert 3/]6" dia. rod or drill into one of the ° SLEEVE holes in the collar...TURN IN THE DIRECTION...
  • Page 11 Apply tension to belt by turning Belt Tension Handle counter clockwise until belt has mod- erate tension on pulleys. Tighten Belt Tension Lock Handles. Belt should deflect approximately 1/2 inch thumb pressure at center of belt. Close belt guard. belt slips while drilling,...

  • Page 12: Getting To Know Your Drill Press

    assembly TABL SCALE POINTER ADJUSTING POINTER With the table squared to the head, the table bevel pointer should be adjusted. Loosen screw in pointer with screwdriver. and move pointer to "0" position on scale. SCREW Retighten screw. getting to know your drill press DEPTH SCALE DRILL "ON-OFF"...
  • Page 13 This Drill Press has 12 speeds as listed below: ® SPINDLE SPEEDS iN R.P.M. ¢_ 300RPM 1450RPM 375RPM 1530RPM 525RPM 2000RPM 1450 1530 ,,,._, 560RPM 2200RPM 700RPM 3400RPM 2000 2200 3400 4600 860RPM 4600RPM ¢ Seeright side of Headfor specificplacement of beltson pulleys.
  • Page 14 getting to know your drill press DRILL "ON.OFF" SWITCH... locking THIS FEATURE IS INTENDED PREVENT UNAUTHORIZED AND POSSIBLE HAZARDOUS CHILDREN insert KEY into switch. NOTE: Key is made of yellow plastic. To turn drill ON.. Insert finger under switch lever and pull. To turn drill OFF..

  • Page 15: Removing The Chuck

    3116" ROD OR DRILL REMOVING THECHUCK LOCKING Insert a piece of 1/4 in. dia. steel rod in one CHUCK of the holes in the chuck body. SLEEVE Insert 3/16 in. dia. rod or drill into one of the holes in the collar.., turn it in the direction of arrow until...

  • Page 16: Installing Drills

    basic drill press operation CHUCK INSTALLING DRILLS Insert drill into chuck far enough to obtain maxi- GRIPPING o{ the CHUCK JAWS...the jaws are approx. 1 in. long. When using a small drill do not insert it so far that the jaws touch the flutes (spiral grooves) of the drill.

  • Page 17: Hole Location

    Before turning switch bring When drilling with the table tilted, ALWAYS CLAMP WORKPIECE AND BACK-UP MATERIAL down to the workpiece lining it up with the ho location. SECURELY TABLE before operating Drill Press. FEEDING To return table to original position: !oosen screw and bevel...

  • Page 18: Maintenance

    maintenance WARNING:, FOR YOUR SAFETY, TURN SWITCH REMOVE PLUG FROM POWER SOURCE OUTLET BEFORE MAINTAIN- ING OR LUBRICATING YOUR DRILL PRESS. Frequently blow out any dust that may accumu- late inside the motor. A coat of automobile-type wax applied to the table and column will help to keep the surfaces clean.

  • Page 19: Quill Return Spring

    trouble shooting WARNING: FOR YOUR OWN SAFETY, TURN SWITCH "OFF" AND ALWAYS REMOVE PLUG FROM POWER SOURCE OUTLET BEFORE TROUBLE SHOOTING. ® CONSULT YOUR LOCAL SEARS SERVICE CENTER IF FOR ANY REASON MOTOR WILL NOT RUN. REMEDY TROUBLE PROBABLE CAUSE 1.
  • Page 20 39 38 •Any attempt to repair this motor may create a HAZARD unless repatr is done by a qualified service technician. Repair service is available at your nearest Sea.rs Store,...
  • Page 21 PARTS LIST FOR CRAFTSMAN 15" DRILL PRESS MODEL NO. 113.213850 Part Part Description Description STD 303240 *Belt "V" 3t8X24 27 71368 60522 Ring, Retaining 28 71340 Knob 60510 Ring, Retaining 29 STD 503705 *Screw, Soc. Set 3!8-16Xl!2 STD 315225 *Bearing,...
  • Page 22 PARTS LIST FOR ..CRAFTSMAN DRILL PRESS MODEL NO. 113.213850 Part Part Description Description 71385 Tube, Column 71373 Spacer 71320 Collar, Rack 71332 Gear, Helical STD 502503 *Screw, Soc. Set 114-20X318 71386 Worm, Elevation 71392 Handle Asm. Table Support...
  • Page 23 PARTS LiST FOR CRAFTSMAN 15" DRILL PRESS MODEL NO, 113.213850 FiG. 1 Part Description 60509 Ring, Retaining 21132 STD315235 *Bearing, Ball 17MM 71384 Tube, Quill 60503 Bearing, Thrust STD315255 *Bearing, Ball 25MM 71374 Spindle 71318 Chuck STD 541150 *Nut, Hex 1/2-20...

  • Page 24: Repair Parts

    i iii.,.i.. Sears MOTORIZED 15 INCH owners FLOOR MODEL manuel DRILL PRESS SERVnCE Now that you have purchased your 15 inch drill press should a need ever exist for repair parts or service, simply contact any Sears Service Center and most Sears, Roebuck and Co.

Table of Contents